• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.22 no.1
• /
• pp.21-29
• /
• 1997

This paper describes implementation contents contents of manual/automatic complex redundancy control mothod for control of a modulation system of a Paging earth station in redundancy stracture. The existed redundancy control method usually is a automatic local control method in which the redundancy switching, including display or alarm beeping through operation of display devices or audio devices, is performed by the co-action of components or modules when the abnormal status is occurred in a modulation system. However, this method introduced in here is designed to enable use of three control modes;1) Manual mode by an operator, 2) Auto-remote mode by the Network Maagement System, through implementation of the redundancy control system composed of the redundancy control board and the redundancy switching circuit.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.26 no.4
• /
• pp.138-144
• /
• 1989

In this paper, a new method is proposed to remove the logical redundancy for the gate-level circuit optimization. In this method, only the fanout-branch signals in the circuits, not all the signals, are examined for redundancy. When a signal is determined to be nonredundant, other nonredundant signals are found out by the efficient procedure, using only the informations which are generated in the course of the redundancy-check. In order to avoid the re-examination of a signal for redudancy, a heuristic method is proposed to determine the redundancy-checking order of signals. The proposed method is heuristic, based on the VLSI test theory. It is much faster than other methods, since it does not reexamine a signal for redundancy.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.33A no.4
• /
• pp.11-17
• /
• 1996

In the case of redundancy control performed by a netowrk management system, it can not be ignored some delay of control time and break of control by failure of the system. This paper proposed a new method to improve the performacne of a redundancy control system interfaced to the network management system. At first, it produced the modelling of the total system and analyzed the functional relation of reliability and failure rate for a transmission system having an one-to-one active redundancy structure controlled by itself. After describing the loss rate of transmission data and the time required for the redundancy control process of the network management system when a failure is occurred, it proposed the new redundancy method of complex system control mode as an effective redundancy control method to improve reliability of a redundancy control system. Finally, it proved the effect by comparing the new result to the previous result.

• Proceedings of the IEEK Conference
• /
• 1998.10a
• /
• pp.711-714
• /
• 1998

본 논문에서는 wide data-width DRAM을 위한 flexible column redundancy scheme을 제안하였다. 구현된 redundancy scheme은 DB line shift method를 사용하여 wide data-width를 갖는 고집적 DRAM에 적용할 때 기존 redundancy scheme보다 더 작은 redundancy cell 면적과 fuse개수를 가지면서 더 큰 flexibility를 가지게 되었다.

• Journal of Korean Society of Steel Construction
• /
• v.21 no.5
• /
• pp.493-503
• /
• 2009

Bridge redundancy is defined as the capability of a bridge to sustain loads after one of its main members incurs damage. It is affected by many parameters, including the number of girders, span length, girder height, internal supports, and secondary members. The present AASHTO and Korean Bridge design codes, however, define bridge redundancy only as the number of girders, and neither the evaluation method nor the required level of redundancy is given. This study presented a redundancy evaluation method for plate girder bridges with severe fatigue damage based on the reliability method,by considering the essential parameters. A required level of redundancy was also proposed as a target system reliability index from the load capacity analysis and reliability analysis of the basis bridge designed by LRFD. Finally, the level of redundancy of simple and continuous plate girder bridges with a variable number of girders designed by ASD was evaluated and presented.

• Journal of Institute of Control, Robotics and Systems
• /
• v.14 no.11
• /
• pp.1180-1188
• /
• 2008

As many systems depend on electronics, concern for fault tolerance is growing rapidly in the safety critical system such as intelligent vehicle. In order to make system fault tolerant, there has been a body of research mainly from aerospace field including predictive hybrid redundancy by Lee. Although the predictive hybrid redundancy has the fault tolerant mechanism to satisfy the fault tolerant requirement of safety crucial system such as x-by-wire system, it suffers form the variability of prediction performance according to the input feature of system. As an alternative to the prediction method of predictive hybrid redundancy for robust fault tolerant, Kalman prediction has attracted some attention because of its well-known and often-used with its structure called Kalman hybrid redundancy. In addition, several numerical simulation results are given where the Kalman hybrid redundancy outperforms with predictive smoothing voter.

• ETRI Journal
• /
• v.31 no.3
• /
• pp.339-341
• /
• 2009

Built-in redundancy analysis (BIRA) is widely used to enhance the yield of embedded memories. In this letter, a new BIRA method for both high repair efficiency and small hardware overhead is presented. The proposed method performs redundancy analysis operations using the spare mapping registers with a covered fault list. Experimental results demonstrate the superiority of the proposed method compared to previous works.

• Journal of Institute of Control, Robotics and Systems
• /
• v.17 no.11
• /
• pp.1132-1137
• /
• 2011

Critical systems with high reliability feature fault tolerant redundancy. Conventional analytical reliability analysis methods that use the Reliability Block Diagram do not adequately reflect characteristics of the redundancy management system and are not suitable for this applications. This paper uses Monte-Carlo method to calculate the reliability of complicated redundant systems. The method was first validated for cases with analytical solutions. Then, the tool was successfully applied to analyze reliability of the flight control systems with a voter as redundancy management system.

• Journal of Institute of Control, Robotics and Systems
• /
• v.15 no.3
• /
• pp.337-345
• /
• 2009

The dependence of numerous systems on electronic devices is causing rapidly increasing concern over fault tolerance because of safety issues of safety critical system. As an example, a vehicle with electronics-controlled system such as x-by-wire systems, which are replacing rigid mechanical components with dynamically configurable electronic elements, should be fault￢tolerant because a devastating failure could arise without warning. Fault-tolerant systems have been studied in detail, mainly in the field of aeronautics. As an alternative to solve these problems, this paper presents the fuzzy hybrid redundancy system that can remove most erroneous faults with fuzzy fault detection algorithm. In addition, several numerical simulation results are given where the fuzzy hybrid redundancy outperforms with general voting method.

• Journal of Korean Society for Quality Management
• /
• v.32 no.4
• /
• pp.125-139
• /
• 2004

Generally, parallel redundancy is used to improve reliability in many systems. However, redundancy increases system cost, weight, volume, power, etc. Due to limited availability of these resources, the system designer has to maximize reliability subject to various constraints or minimize resources while satisfying the minimum requirement of system reliability. This paper presents GAs (Genetic Algorithms) to solve redundancy allocation in series-parallel systems. To apply the GAs to this problem, we propose a genetic representation, the method for initial population construction, evaluation and genetic operators. Especially, to improve the performance of GAs, we develop heuristic operators (heuristic crossover, heuristic mutation) using the reliability-resource information of the chromosome. Experiments are carried out to evaluate the performance of the proposed algorithm. The performance comparison between the proposed algorithm and a pervious method shows that our approach is more efficient.