• Journal of Biomedical Engineering Research
• /
• v.19 no.2
• /
• pp.119-128
• /
• 1998

This paper describes a filtering algorithm which employs apriori information of SPECT lesion detectability potential for the filtering of degraded projection images prior to the backprojection reconstruction. In this algorithm, we determined m minimum detectable lesion sized(MDLSs) by assuming m object contrasts uniformly-chosen in the range of 0.0-1.0, based on a signal/noise model which provides the capability potential of SPECT in terms of physical factors. A best estimate of given projection image is attempted as a weighted combination of the subimages from m optimal filters whose design is focused on maximizing the local S/N ratios for the MDLS-lesions. These subimages show relatively larger resolution recovery effect and relatively smaller noise reduction effect with the decreased MDLS, and the weighting on each subimage was controlled by the difference between the subimage and the maximum-resolution-recovered projection image. The proposed filtering algoritym was tested on SPECT image reconstruction problems, and produced good results. Especially, this algorithm showed the adaptive effect that approximately averages the filter outputs in homogeneous areas and sensitively depends on each filter strength on contrast preserving/enhancing in textured lesion areas of the reconstructed image.

• Journal of Korea Technology Innovation Society
• /
• v.11 no.2
• /
• pp.264-286
• /
• 2008

In 2006, the share of energy in Korea amounted to 28% from the total import, 97% from overseas dependency, and 83% for the national Greenhouse Gas (GHG) emission in 2004. Thus, from the aspects of economical and environmental policies, an energy analysis is very important, for the industry to cope with the imminent pressure for climate change. However, the estimation of GHG gas emissions due to an energy use is still done in a primitive way, whereby each industry's usage is multiplied by coefficients recommended from international organizations in Korea. At this level, it is impossible to formulate the prevailing logic and policies in face of a new paradigm that seeks to force participation of developing countries through so called post-Kyoto Protocol. In this study, a hybrid energy input-output (E-IO) analysis is conducted on the basis of the input-output(IO) table of 2000 issued by the Bank of Korea in 2003. Furthermore, according to economic sectors, emission of the GHG relative to an energy use is characterized. The analysis is accomplished from four points of view as follows: 1) estimating the GHG emission intensity by 96 sectors, 2) measuring the contribution ratio to GHG emissions by 14 energy sources, 3) calculating the emission factor of 3 GHG compounds, and 4) estimating the total amount of national GHG emission. The total amount estimated in this study is compared with a national official statistical number. The approach could be an appropriate model for the recently spreading concept of a Life Cycle Analysis as it analyzes not only a direct GHG emission from a direct energy use but also an associated emission from an indirect use. We expect this model can provide a form for the basis of a future GHG reduction policy making.

• Nutrition Research and Practice
• /
• v.12 no.2
• /
• pp.129-134
• /
• 2018

BACKGROUND/OBJECTIVES: Although several recent studies have reported the anti-cancer effects of extracts or components of Citrus unshiu peel, which has been used for various purposes in traditional medicine, the molecular mechanisms for their effects remain unclear. In the present study, the anti-cancer activity of a water-soluble extract of C. unshiu peel (WECU) in MDA-MB-231 human breast carcinoma cells at the level of apoptosis induction was investigated. MATERIALS/METHODS: Cytotoxicity was evaluated using the MTT assay. Apoptosis was detected using DAPI staining and flow cytometry analyses. Mitochondrial membrane potential, reactive oxygen species (ROS) assay, caspase activity and Western blotting were used to confirm the basis of apoptosis. RESULTS: The results indicated that WECU-induced apoptosis was related to the activation of caspase-8, and -9, representative initiator caspases of extrinsic and intrinsic apoptosis pathways, respectively, and caspase-3 accompanied by proteolytic degradation of poly(ADP-ribose) polymerase and down-regulation of the inhibitors of apoptosis protein family members. WECU also increased the pro-apoptotic BAX to anti-apoptotic BCL-2 ratio, loss of mitochondrial membrane potential and cytochrome c release from mitochondria to cytoplasm. Furthermore, WECU provoked the generation of ROS, but the reduction of cell viability and induction of apoptosis by WECU were prevented when ROS production was blocked by antioxidant N-acetyl cysteine. CONCLUSIONS: These results suggest that WECU suppressed proliferation of MDA-MB-231 cells by activating extrinsic and intrinsic apoptosis pathways in a ROS-dependent manner.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.36 no.1
• /
• pp.49-54
• /
• 2003

This study was conducted to evaluate characteristics of particle composition and organic matter distribution for tidal flat sediments in the Saemankeum area. The tidal flat sediments consist of predominantly sand and a little of silt, whereas the content of clay was very low. The analyzed values of particles of tidal flat sediments were in the range of $4.60\~10.90\;{\phi}$ for mean size and $-0.1\~1.75\;{\phi}$ for sorting and $-1.0\~0.92\;{\phi}$ for skewness and $0.27\~6.75\;{\phi}$ for kurtosis. The tidal flat sediments are interpreted as representing significant effect of the environmental change due to the construction of Saemankeum embankment. The ORP was in the range of -133$\~$200 (mean 73) mV. But 24 stations of the total stations showed reduction condition, The concentration of CODs was in the range of 17.54$\~$6,176.3 mg/kg. The ratio of C/S was 0.02$\~$0.45 (mean 0.24). And the Saemankeum tidal flat sediment was a little effected by input organic pollutants from upper site area. Conclusively, conservation of the Saemankeum tidal flat sediment was requested because it is for the growing fishery and low organic matter.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.9 no.3
• /
• pp.257-265
• /
• 2016

In this study, an optimal design for motor-driven track type traveling system applied into high clearance working machineries in orchard is proposed. Tractive performance and hill climbing ability were predicted and evaluated for the optimal motor traveling system by taking into account of soil characteristics in orchard utilizing the high clearance working machineries. Design criteria for tractive performance were based on the traction force calculated from tractive effort subtracted by motion resistance, while hill climbing ability had its design criteria that fulfill the climbing 20% slope ground at a speed of 3km/h. Based on the evaluation results of traction and climbing ability, two DC48V, 4500rpm, 1.6kW AC motors were independently applied to both left and right side of orbits; each motor is designed to transmit power on driving sprocket of track type traveling system via 50:1 reduction gear ratio. The motor-driven track type traveling system developed in the study found to have 396 kgf of tractive force, which is 12.5% higher than climbing resistance at orchard soil having 20% slope ground (352 kgf), demonstrating sufficient tractive performance and hill climbing ability.

• Journal of KIISE:Databases
• /
• v.33 no.6
• /
• pp.620-630
• /
• 2006

Event-detection is an important application of sensor networks. Join operations can facilitate event-detection with a condition table predefined by a user. When join operations are used for event-detection, it is desirable, if possible, to do in-network join processing to reduce communication costs. In this paper, we propose an energy-efficient in-network join algorithm, called PBA. In PBA, each partition of a condition table is stored along the path from each node to the base station, and then in-network joins are performed on the path. Since each node can identify the parts to store in its storage by its level, PBA reduces the cost of disseminating a condition table considerably Moreover, while the existing method does not work well when the ratio of the size of the condition table to the density of the network is a little bit large, our proposed method PBA does not have such a restriction and works efficiently in most cases. The results of experiments show that PBA is efficient usually and especially provides significant cost reduction over existing one when a condition table is relatively large in comparison with the density of the network, or the routing tree of the network is high.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.20 no.2
• /
• pp.94-101
• /
• 2016

This paper presents an investigation into the durability alkali-activated materials(AAM) mortar and paste samples manufactured using fly-ash(FA) and ground granulated blast furnace slag(GGBFS) exposed to a sulfate environment with different GGBFS replace ratios(0, 30, 50 and 100%), sodium silicate modules($Ms[SiO_2/Na_2O]$ 1.0, 1.5 and 2.0) and initial curing temperatures($23^{\circ}C$ and $70^{\circ}C$). The tests involved immersions for a period of 6 months into 10% solutions of sodium sulfate and magnesium sulfate. The evolution of compressive strength, weight, length expansion and microstructural observation such as x-ray diffraction were studied. As a results, as higher GGBFS replace ratio or Ms shown higher compressive strengths on 28 days. In case of immersed in 10% sodium sulfate solution, the samples shows increase in long-term strength. However, for samples immersed in magnesium sulfate solutions, the general observation was that the compressive strength decreased after immersion. The most drastic reduction of compressive strength and expansion of weight and length occurred when GGBFS or Ms ratios were higher. Also, the XRD analysis of samples immersed in magnesium sulfate indicated that expansion of AAM caused by gypsum($CaSO_4{\cdot}2H_2O$); the gypsum increased up to 6 months continuously.

• Resources Recycling
• /
• v.18 no.2
• /
• pp.39-50
• /
• 2009

Portland cement production is under critical review due to high amount of $CO_2$ gas released to the atmosphere. Attempts to increase the utilization of fly ash, a by-products from thermal power plant to partially replace the cement in concrete are gathering momentum. But most of fly ash is currently dumped in landfills, thus creating a threat to the environment. Many researches on alkali-activated concrete that does not need the presence of cement as a binder have been carried out recently. Instead, the source of material such as fly ash, that are rich in Silicon(Si) and Aluminium(Al), are activated by alkaline liquids to produce the binder. Hence concrete with no cement is effective in the reduction of $CO_2$ gas. In this study, we investigated the influence of the compressive strength of mortar on alkaline activator and curing condition in order to develop cementless fly ash based alkali-activated concrete. In view of the results, we found out that it was possible for us to make alkali-activated mortar with 70MPa at the age of 28days by using alkaline activator manufactured as 1:1 the mass ratio of 9M NaOH and sodium silicate and applying the atmospheric curing after high temperature at $60^{\circ}C$ for 48hours.

• Journal of Soil and Groundwater Environment
• /
• v.8 no.1
• /
• pp.17-26
• /
• 2003

The sorption experiment of cobalt was performed after the TRIGA soil was intentionally contaminated with cobalt was found that the sorption equilibrium coeficiency of soil decontamination was high when the ratio of soil mass to the volume of citric acid becomes 1:5 The TRIGA soil contaminated with 0.01 M, 0.001 M, and 0.0001 M of cobalt solution were decontaiminated with 0.01 M citric acid. The cobalt concentrtion in the wastewater were measured to be correspondingly 36.0, 14.0, 1.5 ppm. The results of wastewater recycling experiment by chemical precipitation method revealed that corresponding cobalt removal efficiency were 97% 88%. It was shown that the removal efficiency decreases as the cobalt concentration in the wastewater decreases. During the decontamination experiment, a lot of NaOH had to be added, and the volume of final solid waste reached almost 10% of that of the contaminated soil. The result of wastewater recyling experiment by ion exchange resin meted rethod revealed that to more the strong acid resins are used, the higher the cobalt removal efficiency becomes and the cobalt removal efficiency becomes and the lower the pH of recycling wastewater become. In order to obtain more than 95% removal efficiency, more than 0.625 g of strong acid resin was necessary in each of 3 experiments. There was an unexpected problem that a lot of strong acid resin waste was produced which amounts to 9.2% (volume) of the contaminated soil.

• Journal of Korean Society of Steel Construction
• /
• v.25 no.2
• /
• pp.131-139
• /
• 2013

The object of this paper is to perform the experiments to investigate the relationship of the resistance forces and the failure temperatures on the failure behaviors of H-shaped steel compressive members. H-shaped members(SS400) were used for the test models and the tests for the elevated temperatures were performed by ISO 834 in FILK(Fire Insurers Laboratories of Korea). The local, overall buckling stresses and a yielding stresses for the failure temperatures were compared with the compressive stresses for the loading forces of test models, the yielding strength and elastic modulus reduction factor of the steel at a high temperature were based on the criteria of the EC3(Eurocode 3) Part1.2(1993). The slenderness ratio was fixed by 45.4 and the compressive forces corresponded with 50%, 70% and 80% of the yielding forces at the normal temperatures were chosen for the loading forces of the test models. The failure temperatures of the test models were investigated under three kinds of loading conditions. It was known that the resistance forces have come close to the yielding forces, not the elastic buckling loads evaluated by EC3 at the failure temperatures obtained from the tests which are related to the failure temperatures and the loading stresses.