• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.55 no.8
• /
• pp.389-395
• /
• 2006

In the single-phase switched reluctance motor (SRM) drive, the required DC source is generally supplied by the circuit consisting of bridge rectifier with diodes and many filter capacitances connected with AC source. Although the peak torque ripple of SRM is small because of large capacity of the capacitance, the charge and discharge time swhich the AC source acts on the capacitance are small and the peak current will pass on the side of source, so power factor and system efficiency decrease. Therefore a novel SRM drive system is presented in this paper, which includes drive circuit realizing reduction of torque ripple and improvement of power factor and switching topology. The proposed drive circuit consists of one switching part and diodes which can separate the output of AC/DC rectifier from the large capacitance and supply power to SRM alternately in order to realize reduction of torque ripple and improvement of power factor through the turn on and turn off of switching part. In addition, the validity of method is tested by simulation and experiment.

• Fashion & Textile Research Journal
• /
• v.12 no.4
• /
• pp.450-458
• /
• 2010

The purpose of this study was to investigate the effect of shopping orientation on price perception and the effect of shopping orientation and price perception on purchase satisfaction. This study administered a questionnaire survey to adults in their 20s and 30s who had once purchased fashion products in surrogate internet shopping malls. Among 327 questionnaires, 263 were collected through convenience sampling and 94 were collected from six internet communities. Data were analyzed by factor analyses and regression analyses. The results of this study are as follows. First, factor analysis of price perception revealed that two factors such as price reasonability and price reduction were extracted and the mean of price reduction was higher than one of price reasonability. Second, factor analysis of purchase satisfaction extracted four factors such as service quality, shopping convenience, product scarcity and product variety/price satisfaction. Mean comparisons showed that the mean of product scarcity was the highest among four factors. Third, regression analyses that recreational, economic, and convenience shopping orientation affected price reduction, a factor of price perception. Fourth, regression analyses showed that shopping orientations and the price perception had significant effects on the purchase satisfaction.

• Journal of Trauma and Injury
• /
• v.25 no.1
• /
• pp.7-16
• /
• 2012

Purpose: Cervical dislocations with locked facets account for more than 50% of all cervical injuries. Thus, investigating a suitable management of cervical locked facets is important. This study examined factors of close reduction failure in traumatically locked facets of the subaxial cervical spine patients to determine suitable surgical management. Methods: We retrospectively analyzed of the case histories of 28 patients with unilateral/bilateral cervical locked facets from Nov. 2004 to Dec. 2010. Based on MRI evaluation of disc status at the injury level, we found unilateral dislocations in 9 cases, and bilateral dislocations in 19 cases, The patients were investigated for neurologic recovery, closed reduction rate, factors of the close reduction barrier, fusion rate and period, spinal alignment, and complications. Results: The closed reduction failed in 23(82%) patients. Disc herniation was an obstacle to closed reduction (p=0.015) and was more frequent in cases involving a unilateral dislocation (p=0.041). The pedicle or facet fracture was another factor, although some patients showed aggravation of neurologic symptoms, most patients had improved by the last follow up. The kyphotic angle were statistically significant (p=0.043). Sixs patient underwent anterior decompression/fusion, and 15 patients underwent circumferential fusion, and 7 patients underwent posterior fusion. All patients were fused at 3 months after surgery. The complications were 1 case of CSF leakage and 1 case of esphageal fistula, 1 case of infection. Conclusion: We recommend closed reduction be performed as soon as possible after injury to maximize the potential for neurological recovery. Patients fot whom closed reduction of the cervical locked facets have a higher incidence of anatomic obstacles to reduction, including facet fractures and disc herniation. Immediate direct open anterior reduction or circumferential fixation/fusion of locked cervical facets is recommended as a treatment of choice for traumatic locked cervical facet patients after closed reduction failure.

• Journal of environmental and Sanitary engineering
• /
• v.18 no.2
• /
• pp.27-33
• /
• 2003

This survey was performed to investigate the NOx emission factors at 3 Municipal Solid Waste Incinerators(MSWI) and 5 Power generation boilers in Seoul. The NOx concentrations were measured before and after control systems. The results were as follows. 1) The NOx reduction efficiencies of Selective Catalytic Reduction (SCR) using ammonia as reducing agent ranged from 53.7% to 89.9%. The NOx reduction efficiencies of SCR using methanol as reducing agent, Non- Selective Catalytic Reduction (NSCR) using ethanol as reducing agent and low-NOx burner were 20.8%, 29.1% and 24.7%, respectively. 2) The NOx emission factors at A-1, A-2 and A-3 facilities of MSWI were 0.786, 0.127 and 0.594 kg Nox/ton fuel, respectively. The factors of A-1 and A-3 facilities were higher than the average value of Korea. 3) The NOx emission factors at B-1, B-2, B-3, B-4 and B-5 facilities of Power generation boiler were 2.109, 0.726, 4.106, 8.378 and 5.168 kg Nox/ton fuel, respectively. The factors of B-4 and B-5 facilities were higher than the average value of Korea.

• Proceedings of the Korean Fiber Society Conference
• /
• 2003.10a
• /
• pp.106-106
• /
• 2003

6 woven geotextiles for reinforcement were used to examine the effects of weatherability and reduction factor on the tensile properties. Decrease of tensile strength as the tool of these evaluations of woven geotextile was examined.

• Journal of the Korean Society of Industry Convergence
• /
• v.9 no.1
• /
• pp.79-86
• /
• 2006

In this study, we research and develope Intelligent Remote management controller. According to the load condition, we will apply various control techniques and plan high efficient Demand control. After development, According to the Demand Control, An electricity enterprisers will expect enlargement of equipment coefficient, elevation of back up load factor and reduction effect of equipment investment. On Customer side, They will expect reduction of electric fee, saving energy and variety of service choice.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.06a
• /
• pp.1410-1415
• /
• 2000

This paper introduces the experimental analysis of the resonator in the rolling piston type compressor for air conditioner. The resonator located between cylinder and bearing is a major factor in the noise reduction of the rotary compressor. Several shapes for the resonator which can be built in the space limitations are derived. Then optimal resonator type for the noise reduction is determined by noise tests. 6 design parameters of the type are found and optimal level for each design factor is deduced from Taguchi method.

• Journal of the Microelectronics and Packaging Society
• /
• v.15 no.3
• /
• pp.1-8
• /
• 2008

Effects of annealing process in a reduction ambient on thermoelectric properties of the $(Bi,Sb)_{2}Te_3$ thin films prepared by thermal evaporation have been investigated. With annealing at $300^{\circ}C$ for 2 hrs in a reduction ambient(50% $H_2$+50% Ar), the crystallinity of the $(Bi,Sb)_{2}Te_3$ thin films were substantially improved with remarkable increase in the grain size. Seebeck coefficients of the $(Bi,Sb)_{2}Te_3$ thin films increased from$\sim90{\mu}V/K$ to $\sim180{\mu}V/K$ with annealing in the reduction ambient due to decrease in the hole concentration. Power factors of the $(Bi,Sb)_{2}Te_3$ thin films were remarkably improved for $5\sim16$ times with annealing in the reduction atmosphere. After annealing in the reduction ambient, a $(Bi,Sb)_{2}Te_3$ evaporated film exhibited a maximum power factor of $18.6\times10^{-4}W/K^{2}-m$.

• Steel and Composite Structures
• /
• v.21 no.3
• /
• pp.629-659
• /
• 2016

In cold-formed stainless steel lipped channel-sections, web openings are becoming increasingly popular. Such openings, however, result in the sections becoming more susceptible to web crippling, especially under concentrated loads applied near the web opening. This paper presents the results of a finite element parametric study into the effect of circular web openings on the web crippling strength of cold-formed stainless steel lipped channel-sections for the interior-one-flange (IOF) loading condition. This involves a bearing load applied to the top flange of a length of member, away from the end supports. The cases of web openings located centred beneath the bearing load (i.e. beneath the bearing plate delivering the load) and offset to the bearing plate, are considered. Three grades of stainless steel are considered: duplex EN1.4462, austenitic EN1.4404 and ferretic EN1.4003. In total, 2218 finite element models were analyzed. From the results of the parametric study, strength reduction factors for load bearing capacity are determined, where these reduction factors are applied to the bearing capacity calculated for a web without openings, to take account the influence of the web openings. The strength reduction factors are first compared to equations recently proposed for cold-formed carbon steel lipped channel-sections. It is shown that for the case of the duplex grade, the strength reduction factor equations for cold-formed carbon steel are conservative but only by 2%. However, for the cases of the austentic and ferritic grades, the cold-formed carbon steel equations are around 9% conservative. New strength reduction factor equations are proposed for all three stainless steel grades.

• Journal of the Korean Geosynthetics Society
• /
• v.17 no.4
• /
• pp.213-224
• /
• 2018

In this study, a series of accelerated creep tests (SIM) was carried out on geosynthetic strip reinforcements with folding grooves having different tensile strengths (15 kN, 25 kN, 35 kN, 50 kN, 70 kN, and 90 kN) to analyze creep characteristics and to assess creep reduction factors. In particular, long-term creep tests were conducted on geosynthetic strip reinforcements with 25 kN tensile strength, which is widely used, to compare and analyze the accelerated creep test results. As a result, the creep reduction factor increased with an increasing design life of reinforcement. In addition, geosynthetic strip reinforcement using the same material and manufacturing method showed similar creep reduction factors at the same design life for different tensile strengths. When both long-term and accelerated creep test data were used, the creep reduction factors from the accelerated test were estimated to be 5.9%~7.1% less than those from the long-term creep test for the design life ranging from 50 to 100 years.