• Journal of Environmental Science International
• /
• v.16 no.3
• /
• pp.385-392
• /
• 2007

Currently, portable equipment for recycling of waste asphalt concrete (ASCON) has been used. However, any air pollution control devices are not attached in the simple portable one. Thus, a lot of air pollutants have been produced from recycling processes of waste ASCON which resulted from aging of paved roads or repavement of roads. This study deals with a preliminary result of concentration analysis of air pollutants obtained from a pilot and a real recycling processes of waste ASCON using simple portable recycling equipment. Air pollutants were taken from 4 steps of the pilot recycling process including an initial heating by liquid petroleum gas (LPG), intermediate heating and melting (H&M) process, final H&M process, and pavement processes using recycled ASCON at the recycling site. Also, air pollutants were taken front 4 steps of the real recycling processes including an initial H&M, final H&M and mixing, loading of recycled ASCON to dump trucks, and at the recycling site after leaving the loaded dump trucks for real pavement sites. The air pollutants measured in this study include volatile organic compounds (VOCs), aldehydes, particulate matter (PM: PM1, PM2.5, PM7, PM10, TSP (total suspended particulate)). The identified concentrations of VOCs increased with increasing time or degree for H&M of waste ASCON. In particular, very high concentrations of the VOCs at the status of complete melting, which is exposed to the air, of the waste ASCON just before paving tv the recycled ASCON at the recycling site. Also, considerable amount of VOCs were identified from the recycling equipment after the dump trucks leaded by recycled ASCON leaved the recycling site for the pavement sites. The relative level of formaldehyde exceeded 80% of the aldehydes Identified in the recycling processes. This is because the waste ASCON is exposed to direct flame of LPG during H&M processes. The PM concentrations measured in the winter recycling processes, such as the loading and rotation processes of waste ASCON into/in the recycling equipment for H&M, were much higher than those in the summer ones. In particular, the concentrations of coarse particles such as PM7 and PM10 during the winter recycling were very high as compared those during the summer one.

• Proceedings of the Korean Institute of Resources Recycling Conference
• /
• 2003.10a
• /
• pp.17-21
• /
• 2003

• Resources Recycling
• /
• v.16 no.1 s.75
• /
• pp.15-27
• /
• 2007

The Korean Auto industry has developed remarkably over the past 30 years. In 2005 alone, Korea produced 3.7 million vehicles, and the number of vehicles registered surpassed the 15 million marks. The rapid growth in registration, however, has given increasing problems to the traffic congestion and the environmental pollution. The system for handling of ELV in Korea is governed by the 'Motor management law'. The law places the responsibility for vehicle scrapping directly on the vehicle owners. The take-back rate of ELV reaches nearly 100% in Korea since 1987. To further entourage recycling, the government introduced the extended producer responsibility system(EPRS) starting January 1, 2003, which imposes waste recycling obligations on producers or importers. According to the system, producers must recycle home appliances and packaging materials. This system, however, did not involve the automobiles. In 2006, the automobiles recycling law is under preparing now by the government. This article is concerning current status for End-of-Life vehicle's recycling and the recycling system model for advanced ELV industries in Korea.

• Journal of the Korea Furniture Society
• /
• v.20 no.1
• /
• pp.31-41
• /
• 2009

In our country, most of the wood resources are imported. We faced a continuous rising of wood price by export country's some conditions and excess rising of transport charge, also a shortage of structural size members. In these situation, recycling or reuse of wood residues and wastes under wood processing industry, building construction and demolition is not a option but a prerequisite. In our country, there is a dearth of data on recycling or reuse of wood residues and wastes, so the investigation on the necessity of recycling or reuse of wood residues and wastes was conducted by using the foreign data and documents. First of all, fields and actual conditions for the domestic wood processing industry were surveyed. Then, kinds and signification of wood residues and wastes were organized. Later, the necessity and the signification of recycling or reuse of wood residues were investigated, and postulations for effective recycling and reuse were suggested. Above all, the necessity of grading standards for reuse or recycling and some important consideration for developing grading standards were emphasized. At last, foreign research tendencies and some applications on recycling or reuse of wood residues and wastes were supplemented.

• Resources Recycling
• /
• v.20 no.3
• /
• pp.3-11
• /
• 2011

Magnesium has been used as parts of vehicles, case materials of notebook PC and mobile phone, and its demand has been increasing recently. So until now, there has little magnesium scraps from the end of life vehicles or electronic parts, and most scraps has been generated from magnesium processing lines such as melting, die casting and machining. It is to review the present status of magnesium recycling. Here, domestic demand of magnesium, recycling amount and technologies used in domestic recycling companies were surveyed in recent years. In 2010, 8,840 tons of magnesium scraps were processed and used as raw materials for die casting products. The recycling ratio was estimated as 32.5%.

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.5
• /
• pp.225-231
• /
• 2003

The injection molding is a traditional manufacturing method that can make plastic parts by just one time in mold. Therefore, the injection molding has become one of a manufacturing method, which is widely applied in a producing of plastic products. Nowadays, to use of plastic parts has increased and plastic product-model using term has been shorten. By these reasons, using term of a injection mold has fast been reduced. These produced molds will be disused and leaved in a storage after a regular term to use it. These leaved molds are sometime sold as scrap iron. But, these molds have lots parts for recycling except special parts for example, cavities, cores and eject pins, etc. In this research, we investigated when the cavity and core of in injection mold would be changed, the injection mold could be recycled. We suggested the structures and standardizations for recycling of a moldbase. We also developed a program in which can be used when the recycling moldbase design in the Auto-CAD with the recycling standards. We called this program as the Recy-Mold. For the availability of the program and moldbase structure fur the recycling standards, we experimented a used mold for automobile lens, which was remanufactured by the recycling standard. The results of this test showed feasibility for the recycling mold.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.1 no.2
• /
• pp.75-83
• /
• 2000

Recently, the quantities of waste asphalt concrete at construction sites have much increased greatly. but maintaining a filling-up and final disposal place is a difficult problem. Therefore, we are faced with a worsening environmental problem brought about present illegal measures. So, safety treatment and recycling of construction waste is a very important question in the Preservation of environmental and natural resources In this study we performed fundamental investigation to manufacture the base recycling asphalt mixture by movable asphalt recycling machine. It contained waste asphalt concrete and recycling agent and its quality was equal to virgin asphalt concrete.

• Resources Recycling
• /
• v.21 no.3
• /
• pp.3-14
• /
• 2012

In order to review the recycling status of urban mine resources in China, recycling of ELV(End of Life Vehicles), E-waste(WEEE) and nonferrous metals were surveyed. Number of the sales volume of the new vehicles were over more than ten million and number of discharge vehicles are increasing now. However, recycling system has not been managed smoothly in China. Though usage of home appliances in urban is similar with advanced countries, there are significant differences in rural community. In the other hand, China is the country with the largest E-waste import in the world. Production and consumption of the nonferrous metals are increasing year by year in China, but recycling of metals is not enough.

• Resources Recycling
• /
• v.9 no.2
• /
• pp.3-10
• /
• 2000

Used aluminum beverage can(UBC) is an important secondary resource. Domestic recycling rate of UBC should be increased from the standpoint of resource savings and environmental protection. Aluminum can to can recycling is divided into two steps. The first step was composed of the processes such as collection of used beverage cans, shredding, magnetic separation, de-lacquring, melting and casting. The second is remelting and casting, heat treatment, hot and cold rolling, annealing, and can making. With brief discussion about this recycling technology, this article covers aluminum can consumption, the present state of aluminum can recycling in Korea, Japan, USA, and Europe.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.2
• /
• pp.130-135
• /
• 2002

A new Sign algorithm which has improved convergence speed is presented. The data-recycling technique, whose coefficients are multiply adapted in a symbol time period by recycling the received data, is applied to Sign algorithm which has few multiplications. Sign algorithm has very few multiplications and is the most easily implemented, but it gives small rate of convergence relative to others. The proposed algorithm combines the advatage of Sign algorithm, few multiplications, and the virtue of Data-Recycling LMS algorithm, simplicity and fast convergence. The results of computer simulation show that the proposed algorithm has 2 times faster convergence rate than that of LMS algorithm. Comparing to Data-Recycling LMS algorithm, in similar convergence conditions, it requires half fewer multiplications.