• Environmental Engineering Research
• /
• v.13 no.3
• /
• pp.141-146
• /
• 2008

Transport of Escherichia coli ATCC 11105 through porous media was investigated in this study using two sets of column experiments to quantify the attachment-related parameters (sticking efficiency, attachment rate coefficient and filter factor). The first set of experiments was performed in quartz sand under different ionic strength conditions (1, 20, 100, 200 mM) while the second experiments were carried out in quartz sand mixed with metal oxyhydroxide-coated sand (0, 5, 10, 25%). The breakthrough curves of bacteria were obtained by monitoring effluent, and then bacterial mass recovery and attachment-related parameters were quantified from these curves. The first experiments showed that the mass recoveries were in the range of 13.3 to 64.7%, decreasing with increasing ionic strength. In the second experiments, the mass recoveries were in the range of 15.0 to 43.4%, decreasing with increasing coated sand content. The analysis indicated that the sticking efficiency, attachment rate coefficient and filter factor increased with increasing ionic strength and coated sand content. The value of filter factor in the first experiments ranged from 1.45 e-2 to 6.72 e-2 1/cm while in the second experiments it ranged from 2.78 e-2 to 6.32 e-2 1/cm. Our filter factor values are one order of magnitude lower than those from other studies. This discrepancy can be attributed to the size of sand used in the experiment. The analysis demonstrated that the travel distance of bacteria estimated using the filter factor can be varied greatly depending on the solution chemistry and charge heterogeneity of porous media.

• Journal of the Korean Society of Industry Convergence
• /
• v.25 no.3
• /
• pp.423-431
• /
• 2022

The UPS(Uninterruptible Power Supply) system operates in the battery charging mode when the grid is normal, and in the UPS mode, which is the battery discharge mode when a grid error occurs. Since the UPS must supply the same voltage as the grid to the load within 4 [ms] in case of a grid error, the switching time and power recovery time should be short when controlling the output voltage and current of the UPS, and the power failure detection time is also important. The power outage detection algorithm using DFT(Discrete Fourier Transform) proposed in this paper compares the grid voltage waveform with the voltage waveform including the 9th harmonic generated through DFT using Schmitt trigger to detect power outage faster than the existing power outage monitoring algorithm. There are advantages. Therefore, it is possible to supply instant and stable power when switching modes in the UPS system. The multi-power-applied UPS system proposed in this paper uses DFT, which is faster than the conventional blackout monitoring algorithm in detecting power failure, to provide stable power to the load in a shorter time than the existing power outage monitoring algorithm when a system error occurs. The detection method was applied. The changeover time of mode switching was set to less than 4 [ms], which is 1/4 of the system cycle, in accordance with KSC 4310 regulation, which was established by the Industrial Standards Council on the regulation of uninterruptible power supply. A 10 [kW] UPS system in which commercial voltage, vehicle generator, and auxiliary diesel generator can be connected to each of the proposed transfer devices was constructed and the feasibility was verified by conducting an experiment.

• Journal of fish pathology
• /
• v.36 no.2
• /
• pp.213-228
• /
• 2023

We evaluated the transcriptional response of interferon (IFN)-related genes in rock bream iridovirus (RBIV)-infected rock bream under high-, low-, or no-mortality conditions induced by different stocking water temperatures. Under the high susceptibility condition (group A, water temperature 26℃, 100% mortality), only the Mx gene was expressed early, with prolonged expression, and with heavy viral loads of approximately 10⁶~10⁷ major capsid protein gene copies/μL from 4 to 10 days post infection (dpi). However, IRF1, IRF3, IRF8, STAT1, ISG15, PKR, Viperin, GVIN1, IFI44, and ISG56 were activated at later time points (8 dpi) and then quickly decreased (10 dpi). For the low susceptibility condition, the water temperature was set at 23℃ for 7 days (group B) and then reduced to 17℃. Group B exhibited a 28% mortality rate, in which persistent and effective antiviral responses were observed for long periods of time. In particular, at 20 and 22 dpi, when virus replication was peaked at approximately 10⁷/μL, the expressions of most of the IFN-related genes (IRF1, IRF3, IRF8, Mx, STAT1, ISG15, PKR, Viperin, GVIN1, IFI44, and ISG56) were significantly higher in group B than in the control group. Moreover, prolonged and higher levels of IRF3 (at least 30 dpi), IRF8 (at least 30 dpi), ISG15 (at least 30 dpi), PKR (at least 28 dpi), Viperin (at least 30 dpi), and IFI44 (at least 30 dpi) were also observed in the recovery stage of infection. Under the no-susceptibility condition at 17℃ (0% mortality), significantly elevated levels of IRF3, Mx, ISG15, and PKR were observed mostly until 20 dpi. The findings indicate that RBIV infection can induce an efficient IFN-mediated antiviral immune response in low- and no-susceptibility conditions. The findings could be valuable for effective control of viral pathogens in fish.

• Korean Journal of Adult Nursing
• /
• v.17 no.3
• /
• pp.435-443
• /
• 2005

Purpose: This study investigated the degree of fatigue of hemodialysis patients, and finds the relationship between fatigue and self-efficacy, family support, and sleep factor. Also, this study was purposed to provide fundamental data to help set up a nursing plan and intervention for recovery and mitigation of hemodialysis patient's fatigue. Method: The subjects in this study were patients treated as hemodialysis patients in Kwangjoo City. Data, subjects are 143 patients. Fatigue was measured using Lee's scale(1991), Self-efficacy using Kim's scale(1995), and Family support using Kim's scale(1993). For the analysis of collected data, Cronbach alpha, descriptive statistics, t-test, ANOVA, Pearson's correlation coefficient, Stepwise multiple regression were used for statistical analysis by SPSSwin(version 11.0) program. Result: Fatigue degree of hemodialysis patients averaged 4.22. Among 143 hemodialysis patients, 70.63% patients answered that they had felt fatigue as noted in this study. The weariest time was after hemodialysis for 21.0% patients. There was significant difference according to the diagnosis period. The patients who were diagnosed over one year had felt more fatigue than ones who were diagnosed within one year. Fatigue was significantly associated with self-efficacy, family support, and sleep factor. Self-efficacy could explain 14.6% of fatigue. Conclusion: The fatigue degree relates with all, self-efficacy, family support, and sleep factor. Especially, it is affected by self-efficacy among them. Thus, the program should be developed to mitigate fatigue as the self-efficacy of hemodialysis is enhanced.

• Herbal Formula Science
• /
• v.20 no.2
• /
• pp.37-46
• /
• 2012

Objectives : Oyaksungi-san(Wuyaoshunqisan) has been used for treatment of stroke and rheumatoid arthritis in Korea. In this study, a simple and accurate high-performance liquid chromatography(HPLC) method was established for simultaneous determination of six main components, liquiritin, ferulic acid, naringin, hesperidin, neohesperidin, and glycyrrhizin in Oyaksungi-san, a traditional Korean herbal prescription. Methods : The analytical column for separation of six constituents was used a Gemini $C_{18}$ column maintained at $40^{\circ}C$. The mobile phase consisted of two solvent systems, 1.0% (v/v) acetic acid in $H_2O$ (A) and 1.0% (v/v) acetic acid in acetonitrile (B) by gradient flow. The flow rate was 1.0 mL/min and the detector was a photodiode array (PDA) set at 254 nm for glycyrrhizin, 280 nm for liquiritin, naringin, hesperidin, and neohesperidin, and 320 nm for ferulic acid. Results : Calibration curves were acquired with $r^2$ values ${\geq}0.9998$. The results of recovery test were 91.58%-105.90% with a relative standard deviations (RSDs, %) value less than 2.0%. The values of RSD for intra- and inter-day precision were 0.03%-1.72% and 0.03%-1.63%, respectively. The contents of the six compounds in Oyaksungi-san were 0.33-9.30 mg/g. Conclusions : The newly established HPLC method will be helpful to improve quality control of Oyaksungi-san.

• The KIPS Transactions:PartB
• /
• v.16B no.3
• /
• pp.233-238
• /
• 2009

This paper presents an approach to the classifications of small size document using the instance-based feature filtering Relief-F algorithm. In the document classifications, we have not always good classification performances of small size document included a few features. Because total number of feature in the document set is large, but feature count of each document is very small relatively, so the similarities between documents are very low when we use general assessment of similarity and classifiers. Specially, in the cases of the classification of web document in the directory service and the classification of the sectors that cannot connect with the original file after recovery hard-disk, we have not good classification performances. Thus, we propose the Extended Relief-F(ERelief-F) algorithm using instance-based feature filtering algorithm Relief-F to solve problems of Relief-F as preprocess of classification. For the performance comparison, we tested information gain, odds ratio and Relief-F for feature filtering and getting those feature values, and used kNN and SVM classifiers. In the experimental results, the Extended Relief-F(ERelief-F) algorithm, compared with the others, performed best for all of the datasets and reduced many irrelevant features from document sets.

• Journal of Powder Materials
• /
• v.25 no.4
• /
• pp.296-301
• /
• 2018

In this study, an experiment is performed to recover the Li in $Li_2CO_3$ phase from the cathode active material NMC ($LiNiCoMnO_2$) in waste lithium ion batteries. Firstly, carbonation is performed to convert the LiNiO, LiCoO, and $Li_2MnO_3$ phases within the powder to $Li_2CO_3$ and NiO, CoO, and MnO. The carbonation for phase separation proceeds at a temperature range of $600^{\circ}C{\sim}800^{\circ}C$ in a $CO_2$ gas (300 cc/min) atmosphere. At $600{\sim}700^{\circ}C$, $Li_2CO_3$ and NiO, CoO, and MnO are not completely separated, while Li and other metallic compounds remain. At $800^{\circ}C$, we can confirm that LiNiO, LiCoO, and $Li_2MnO_3$ phases are separated into $Li_2CO_3$ and NiO, CoO, and MnO phases. After completing the phase separation, by using the solubility difference of $Li_2CO_3$ and NiO, CoO, and MnO, we set the ratio of solution (distilled water) to powder after carbonation as 30:1. Subsequently, water leaching is carried out. Then, the $Li_2CO_3$ within the solution melts and concentrates, while NiO, MnO, and CoO phases remain after filtering. Thus, $Li_2CO_3$ can be recovered.

• Safety and Health at Work
• /
• v.10 no.2
• /
• pp.196-204
• /
• 2019

Background: Liquid chromatography-tandem mass spectrometry (LC-MSMS) for simultaneous analysis of multiple microbial secondary metabolites (MSMs) is potentially subject to interference by matrix components. Methods: We examined potential matrix effects (MEs) in analyses of 31 MSMs using ultraperformance LC-MSMS. Twenty-one dust aliquots from three buildings (seven aliquots/building) were spiked with seven concentrations of each of the MSMs ($6.2pg/{\mu}l-900pg/{\mu}l$) and then extracted. Another set of 21 aliquots were first extracted and then, the extract was spiked with the same concentrations. We added deepoxy-deoxynivalenol (DOM) to all aliquots as a universal internal standard. Ten microliters of the extract was injected into the ultraperformance LC-MSMS. ME was calculated by subtracting the percentage of the response of analyte in spiked extract to that in neat standard from 100. Spiked extract results were used to create a matrix-matched calibration (MMC) curve for estimating MSM concentration in dust spiked before extraction. Results: Analysis of variance was used to examine effects of compound (MSM), building and concentration on response. MEs (range: 63.4%-99.97%) significantly differed by MSM (p < 0.01) and building (p < 0.05). Mean percent recoveries adjusted with DOM and the MMC method were 246.3% (SD = 226.0) and 86.3% (SD = 70.7), respectively. Conclusion: We found that dust MEs resulted in substantial underestimation in quantifying MSMs and that DOM was not an optimal universal internal standard for the adjustment but that the MMC method resulted in more accurate and precise recovery compared with DOM. More research on adjustment methods for dust MEs in the simultaneous analyses of multiple MSMs using LC-MSMS is warranted.

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2004.02a
• /
• pp.245-256
• /
• 2004

The extraction of three kinds of amido podands, N,N,N'N'-tetrabutyl-3-oxa-pentanedi- amide (TBDGA), N,N,N'N'-tetra-isobutyl-3-oxa-pentanediamide(TiBDGA) and N,N,N'N'-tetra- butyl-3,6-dioxa-oct-anediam- ide(TBDOODA) on U(VI),Pu(IV), Am(III), Eu(III) and other metal ions is studied in nitric acid solutions. 40%octanol-kerosene is chosen as diluents to eliminate third phase and emulsion. TBDGA and TiBDGA show extraction selectivity to An(III) and Ln(III) much higher than to U(VI) and Pu(IV). Fe, Ru and Mo is poorly extracted by the three kinds of amid podands in 2~3mol/L $HNO_3$ solutions. Aiming to eliminate interface crude when using simulated HLLW solution in the system of 0.2mol/L TBDGA/Octanol＋kerosene, acetohydroxyamic acid was adapted. Distribution ratio of zirconium was decreased when adding acetohydroxyamic acid in aqueous solution, and interface crude disappeared as mixing extractant with HLLW. The counter-current extraction test is carried out in a set of miniature mixer-settler, with 0.2mol/L TBDGA/ 40% octanol-kerosene as extractant to separate U(VI), Pu(IV), Am(III) and Eu(III) from simulated high level liquid waste(HLLW) solution. In battery A, lanthanides and actinides are coextracted into organic phase with the recovery of 99.98% for U(Ⅵ), >99.99% for Pu(IV), and >99.99% for Am(III) and Eu(III) respectively. In battery R1, 99.99% U, 86.2% Pu and a part of Am or Eu are stripped into aqueous phase by 0.2mol/L acetohydroxyamic acid (AHA) in 0.01mol/L $HNO_3$ solution. In battery $R_2$, Am, Eu and remained Pu are completely back-extracted by 0.2mol/L AHA. This separation process contains no salt reagent, and it is not necessary to dilute HLLW feed.

• Journal of the Korean Wood Science and Technology
• /
• v.39 no.3
• /
• pp.206-212
• /
• 2011

It was investigated the hardness and dimensional stability of heat-compressed wood by compression temperature and time. The surface hardness of heat-compressed wood increased with increasing compression temperature. The lowest hardness value (5.0 N/$mm^2$) was observed in the temperature $70^{\circ}C$ while the highest value (15.6 N/$mm^2$) was obtained in compression temperature $220^{\circ}C$. Dimensional recovery test results showed that fixation of compression set improved with increasing compression temperature. However, the fixation effects were negligible by press time. Contact angle increased with increasing press temperature and time.