• International Journal of Concrete Structures and Materials
• /
• v.8 no.4
• /
• pp.301-307
• /
• 2014

Rice husk ash (RHA) is classified as a highly reactive pozzolan. It has a very high silica content similar to that of silica fume (SF). Using less-expensive and locally available RHA as a mineral admixture in concrete brings ample benefits to the costs, the technical properties of concrete as well as to the environment. An experimental study of the effect of RHA blending on workability, strength and durability of high performance fine-grained concrete (HPFGC) is presented. The results show that the addition of RHA to HPFGC improved significantly compressive strength, splitting tensile strength and chloride penetration resistance. Interestingly, the ratio of compressive strength to splitting tensile strength of HPFGC was lower than that of ordinary concrete, especially for the concrete made with 20 % RHA. Compressive strength and splitting tensile strength of HPFGC containing RHA was similar and slightly higher, respectively, than for HPFGC containing SF. Chloride penetration resistance of HPFGC containing 10-15 % RHA was comparable with that of HPFGC containing 10 % SF.

• Journal of the Korean Applied Science and Technology
• /
• v.20 no.2
• /
• pp.87-93
• /
• 2003

Two-component polyurethane flame retardant coatings (ATTBC) were prepared by blending polyisocyanate (TDI-adduct) with ATTBs mentioned at the previous paper. Most of the physical properties of the flame retardant coatings were comparable to those of non-flame retardant coatings. Especially, the hardness, impact resistance, and accelerated weathering resistance were remarkably improved with the increase of the content of 1,4-butanediol. Coatings containing 10 and 15 wt% 1,4-butanediol, ATTBC-10C and ATTBC-15C, were not flammable in vertical flame-retardancy test. Their char area recorded 1.1${\sim}$11.6 $cm^2$ in 45$^{\circ}$ eckel burner method.

• Advances in concrete construction
• /
• v.15 no.3
• /
• pp.149-159
• /
• 2023

Water glass (WG) and sodium sulfate (SS) were used to prepare polymeric aluminum chloride residue cement mortar (PACRM) by single and compound blending with polymeric aluminum chloride waste residue, respectively. The structural strength and textural characteristics examinations showed that PACRM consistency increased by incorporating WG, but decreased by incorporating SS. When WG and SS were compounded, the mortar consistency initially rose before falling. The compressive strength of PACRM increased and then decreased as WG was increased. The mechanical properties of PACRM were better enhanced by SS than WG, showing no strength deterioration. The main reason for the improved mechanical properties of polymeric aluminum chloride waste residue in the presence of activators is the increased precipitation of reactive substances, such as C-S-H gels, calcium silica, and Ca(OH)₂. The density of the specimens with PACRM and the degree of aggregation of hydration products were significantly enhanced by generating more hydration products in the mortar. Further, the cracks and pores were significantly reduced, and the matrix structure was continuous and dense at 5% SS doping and 3% compound doping.

• Polymer(Korea)
• /
• v.29 no.6
• /
• pp.565-570
• /
• 2005

Melt processing characteristics of nylon 6 (N6) has been investigated by controlling the melt viscosity in melt impregnation process. Calcium stearate (CaST) was introduced as a lubricant for N6 and the melt viscosity of N6 decreased with adding only 1 wt$\%$ of CaST. In addition, reactive blending with polycaprolactone (PCL) was carried out by lowering the melt viscosity in N6. It was found that the melt viscosity of N6 could be controlled and further melt viscosity drop could be obtained by applying phenyl phosphite (PP) and diphenyl phosphite (DPP) to enhance the transesterification between N6 and PCL. Our approaches show that the melt viscosity of N6 could be reduced without loss of thermal stability which is the critical problem in high temperature melt impregnation process of N6.

• Polymer(Korea)
• /
• v.30 no.1
• /
• pp.22-27
• /
• 2006

The effect of transesterification on the rheological property of poly(ethylene naphthalate)/poly(butylene tore-phthalate) (PEN/PBT) blends has been investigated. The melt viscosity of PEN/PBT blends decreased with increasing PBT content due to the relatively low melt viscosity of PBT as well as introducing ransesterification between PEN and PBT Further melt viscosity decrease was achieved by the thermal annealing which caused both the chain scission and the acceleration of transesterfication. Calcium stearate (CaST) was applied as a lubricant in order to lower the melt viscosity of PEN and it was found that CaST was acting as the catalyst of transesterification as well. In general, reactive melt blending of PEN and PBT by transesterification resulted in the decrease of molecular weight of PEN and PBT, as a result, the loss of mechanical properties in PEN/PET blend was inevitable.

• Polymer(Korea)
• /
• v.29 no.5
• /
• pp.475-480
• /
• 2005

The lowering of melt viscosity has been investigated to achieve the processability enhancement in poly(ethylene naphthalate) (PEN) melt processing by the reactive melt blending with poly(ethylene terephthalate) (PET) and introducing lubricant as well. CaST lubricant resulted in the lowering of PEN melt viscosity but noticeable mechanical property drop was found in PEN with more than $2wt\%$ of lubricant due to the acceleration of thermal degradation by excess lubricant. PEN/PET (90/10) blend has less melt viscosity than PEN and transesterification between two polymers caused the additional viscosity depression. further viscosity lowering was found in PEN/PET blend with CaST since CaST is acting as the catalyst of transesterification as well as a lubricant in PEN/PET blend.

• Applied Chemistry for Engineering
• /
• v.10 no.4
• /
• pp.497-501
• /
• 1999

The changes of properties were studied for the polypropylene(PP)/Nylon6 blends containing different kinds of compatibilizer made by either reactive extrusion of solution reaction. The compatibilizers were PP grafted with maleic anhydride (MAH) made by reactive extrusion and solution reaction. The grafted MAH contents were 0.3 wt %, and 2.7 wt %, respectively. The composition of the PP/nylon6 blend was fixed at 75/25 by weight. Blending was carried out with twin-screw extruder (L/D=30, ${\psi}=30$) at 300 rpm. As the content of PP-g-MAH was increased, the crystallization peak of Nylon6 decreased gradually then finally disappeared. Disappearance of crystallization peak of Nylon6 was mostly affected by grafted MAH content rather than the preparation method and the amount of compatibilizer. The portion of Nylon6 that could not crystallize in its normal crystallization temperature crystallized together with PP at the crystallization temperature of PP. So called concurrent crystallization was observed. Meanwhile two more peaks were observed during heating cycle. One was exothermic peak at $193^{\circ}C$ near to crystallization temperature of Nylon6, the other was endothermic peak at $215^{\circ}C$ that was $5^{\circ}C$ lower than normal endothermic peak of Nylon6. To analyze the peaks, nylon6 was annealed in the differential scanning calorimeter. As a result, the peak at $193^{\circ}C$ was crystallization peak of imperfect crystalline of Nylon6 and the other peak at $215^{\circ}C$ was melting peak of imperfect crystalline of nylon6.

• Polymer(Korea)
• /
• v.33 no.4
• /
• pp.284-289
• /
• 2009

The morphology and mechanical properties of epoxy/polyamide/MPD reactive blends with various amount of polyamide were investigated. The cure behaviors, mechanical strengths, and morphological changes of the epoxy blend systems were analyzed by using DSC, UTM, and SEM, respectively. The amount of high soluble polyamide in epoxy ranged from 0 to 30 phr, and the cure reaction occurred at $170^{\circ}$ for 30 min. The start and maximum exothermic temperature in heat flows during cure reactions appeared at almost same temperature, indicating that soluble polyamide could rarely hinder the cure reactions. From the SEM images, it was found that the size of separated-phase was very fine about 100-300 nm, and at 20 phr of polyamide the boundary of separated-phase was unclear and the phase revealed co-continuous. By AP plasma treatment of specimen surface, the adhesion strength was increased by 20% due to enhanced surface free energy. By blending 20 phr of polyamide with epoxy, the adhesion strength was increased by 50% due to co-continuous phase in morphology. By considering the surface treatment of specimen and morphological tuning of the blends, it can be expected that the improvement in toughness and excellent adhesion strength can be achieved in structural adhesive systems.

• Elastomers and Composites
• /
• v.38 no.3
• /
• pp.262-272
• /
• 2003

Maleic anhydride-grafted-polypropylene(PP-g-MA) were used as a blend component and a compatibilizer, respectively, for two reactive blends of polyamide 66(PA 66)PP-g-MA binary blends and PA 66/polypropylene(PP)/PP-g-MA ternary blends. The goal of this work was to investigate the property differences between binary and ternary blends. Tensile strength, flexural modulus, heat deflection temperature, impact strength, melt flow index, and the dependence of melt viscosity on the shear rate were examined. The impact strengths of binary blends were higher than those of ternary blends at all compositions, since the in situ synthesis of PP-g-PA 66 copolymer through the imide formation between the amine end group of PA 66 and the anhydride group of PP-g-MA gave the increase of molecular weight and was more popular in binary blends than in ternary blends. In case of ternary blends, most of the properties were superior to those of binary blends, owing to the better properties of PP compared with PP-g-MA. The toughened binary blends with 70/30(PA 66/PP-g-MA) and 80/20 ratios were not commercially applicable due to their poor processibility. So, the ternary blends which showed lower melt viscosities were recommended for the commercial applications.

• Journal of the Korean Applied Science and Technology
• /
• v.31 no.4
• /
• pp.584-594
• /
• 2014

To increase of surface hydrophilicity of polymeric thin films is an important approaching technique for introduction of self-cleaning and/or antifogging properties on the surfaces of those films. In general, hydrophilic surface can be produced by coating non ionic surfactants or by increasing surface energy. Various non-ionic surfactants, such as Tween, Span, and PEG-PPG block copolymers were selected for our experiments, because they are cheap and well soluble in toluene system as well as they contain several reactive hydroxy fuctional groups with coupling agents. Blending conditions influence the PET film surface hydrophilicities. However, the introduction of only these surfactants on the surface of PET films did not show the high durability of hydrophilic properties after washing with water. To improve the durability two types of coupling agents such as epoxide and diisocyanate were adopted. Contact angle of water on hydrophilically coated PET film surface with 6 wt% of isophrone diisocyanate(IPDI) containing coating solution was reached to $8.7^{\circ}$, which was an indirect evidence for very high surface hydrophilicity. A light(500 nm of wavelength) transmittance value of coated PET film was changed only from 87% to 85% with keeping a good transparent property. This film can be usable for self-cleaning film industries.