• 한국방사선학회논문지
• /
• 제5권5호
• /
• pp.223-229
• /
• 2011

X선은 X선관 내 음극측 전자(electron)를 빠른 속도로 가속시킨 다음 진행하는 전자의 흐름을 저지극(target)에서 차단시킬 때 에너지의 변환을 일으켜 발생한다. 가속된 고속의 전자가 저지면에 충돌하는 실제면적을 실초점(actual focal spot)이라 하고, 실초점의 크기를 X선이 나오는 방향인 중심선(central ray)측에서 관측할 경우 축소되어 작게 보이는데 이때의 초점을 실효초점(effective focal spot)이라고 한다. X선관 방사각에 따라 음극 측의 강도가 양극 측 보다 높게 나타나 X선 강도가 균등하지 않다. 이러한 효과를 경사각 효과(heel effect)라고 하며, 경사각 효과로 인하여 환자가 받는 피폭의 정도는 양극의 각도, 즉 실효초점의 크기에 따라 달라지게 된다. 본 논문에서는 실효초점의 크기와 그에 따른 환자 피폭선량의 상관관계를 알아보고 실효초점의 크기에 따른 균질선량 분포를 위한 효과적인 조사야를 제시하고자 한다. 결론적으로 초점크기에 따라서 평균적으로 -8cm ~ 0cm 범위에서 효과적인 조사야 범위를 찾을 수 있었고, 평균 선량률은 0.019 R/min이 나왔다. 이 범위를 이용하면 환자에게는 적은 피폭선량으로 균등한 흑화도 및 해상력을 가진 영상을 얻을 수 있을 것이다.

• 대한방사선기술학회지:방사선기술과학
• /
• 제42권6호
• /
• pp.423-428
• /
• 2019

The Precise measurement of the knee's Congruence angle is required for diagnosis of patella dislocation. The purpose of this study is to consider the distortion diagram and usefulness about the test of the bilateral side and one side through the evaluating congruence angle from Merchant view of patellofemoral joint to central X-ray. We've evaluated the sulcus angle and Congruence angle following central X-ray's changes when we took Merchant view of patellofemoral joint aimed to right lower limb from human whole body phantom. The subject of the evaluation was classified as normal group and varus group, and the varus group has experimented with External rotation of legs as 15° and 30°. When normal groups result as 0, 7.5, 15 cm, it was measured as 17.25 ± 1.34°, 19.60 ± 1.41°, 20.55 ± 1.77° each. The gap between minimal and maximum angle was 3.3°, and the value was shown as getting bigger when it further away from the centeral X-ray. When Congruence angle in 15° varus group was 0, 7.5, 15 cm, it was each 16.45 ± 1.34°, 17.10 ± 0.99°, 17.80 ± 1.13°. And when Congruence angle in 30° varus group was 0, 7.5, 15 cm, it was measured each 18.35 ± 1.63°, 18.95 ± 1.06°, 19.60 ± 1.41°. The difference between minimum and maximum of angle in 15° varus group and 30° varus group was each 1.35° and 1.25°, the angles have shown as increasing the further away from the center. The patellofemoral joint showed that the congruence angle increases as the further away from Central X-ray, and also it is judged that is possible to change the congruence angle by a degree of varus knee. Thus, accurate measurement of the congruence angle is shown to advantage that methods for examining by split each side at two times than methods for examining both sides at a time. Therefore, it is expected to helpful on the diagnostic side of patella dislocation and subluxation.

• 대한방사선기술학회지:방사선기술과학
• /
• 제11권2호
• /
• pp.27-64
• /
• 1988

Most hospital administrators in our country have doubted whether or not the size of their hospital personnel staffs, and the personnel management styles implemented are efficient or not. Actually, increased personnel expenditures due to sophisticated specialization of medical practices has become the biggest hospital expense. Therefore, it is said that hospitals can be run move efficiently by implementing reasonable management strategies for hospital personnel management. In this paper, the departments of diagnostic radiography in 16 general hospitals in Seoul, which were classified into 4 groups by the scale of hospital beds, were used as sample cases. Then, the data for the number of X-ray examination by diagnostic item was collected from sample hospitals. The unit hour spent on X-ray examinations in each diagnostic service was quoted from "A Study on setting-up of the relative value units of medical services and on the structure of current fee schedules" written by Mr. Ik Je Seong. The data analysis results are as follows; First, the number of hours per day spent on X-ray examinations in 13 hospitals out of 16 hospitals, was shorter than the general daily working hours (8 hours). Second, in the morning there was not enough time to work for X-ray examinations required, with the available manpower. In the afternoon, however, the situation was diametrically opposed to that in the morning. Third, in light of above results, though most hospitals employ sufficient personnel for the quantity of the actural work, they were always short-handed where their works were performed Fourth, this study tells us that there is a maldistribution of the work in the schedule : too much work for the available personnel in the morning. The following recommendations are resulted from the data analysis described above. First, it is recommended that all out-patients coming again, except specific patients(G. B. or I.V.P. etc) who have to have their X-ray examinations on an empty stomach in the morning among out-patients, be required to visit the hospital in the afternoon. Second, it is recommended that all new out-patients be required to make a reservation in order to equalize the number of patients throughout the day. Third, it is recommended that all in-patients, except specified patients, be arranged to have their X-ray examinations in the afternoon. Fourth, it is recommended that part time workers be employed during peak hours. This recommendation, if applied in a wider scale, would allow hospitals to overcome the problem of the maldistribution of work and personnel, and then more efficient hospital management through the appropirate personnel management procedures could be expected.

• Journal of Chest Surgery
• /
• 제37권12호
• /
• pp.1019-1021
• /
• 2004

신경종은 후종격동 종양의 흔한 형태이며 주로 증상 없이 단순흉부촬영상 우연히 발견되거나 흉통이나 요통 등의 신경압박증상이나 기관지를 압박하여 나타나는 증상 등에 의해 발현되기 쉽다. 하지만 본 증례와 같이 자발성 혈흉을 일으키는 경우는 극히 드물다. 환자는 45세 남자로 갑자기 생긴 흉통 및 호흡곤란을 증상으로 타 병원 응급실 내원하여 시행한 단순흉부촬영상 우측 늑막삼출이 의심되어 폐쇄성 흉관삽입술 후 혈흉으로 진단되었고 흉부 전산화단층촬영상 후종격동 종양 소견 보여 본원으로 전원되었다. 전원 후 시행한 흉추 자기공명영상촬영상 아령모양의 신경종 의심되어 수술적 절제를 시행하였고 병리조직검사상 신경섬유초종으로 판명되었다.

• Advances in materials Research
• /
• 제6권1호
• /
• pp.1-12
• /
• 2017

The aim of the work was to evaluate the effect of ultraviolet-ozone ($UV-O_3$) irradiation with different times on the structure and thermal properties of hydroxypropyl methylcellulose (HPMC) in the form of a thin film to be used as bioequivalent materials according to their important broad practical and medical applications. HPMC thin films were exposed to $UV-O_3$ radiation in air at a wavelength of 184.9 nm.The beneficial effects of this treatment on the crystallinity and amorphousity regions were followed by X-ray diffraction technique and FTIR spectroscopy. Differential scanning calorimetry, thermogravimetric and differntial thermal analyses were used in order to study the thermal properties of HPMC samples following the process of photodegradation. The obtained results indicated that the rate of degradation process was increased with increasing the exposure time. Variations in shape and area of the thermal peaks were observed which may be attributed to the different degrees of crystallinity after exposing the treated HPMC samples. This meant a change in the amorphousity of the treated samples, the oxidation of its chemical linkages on its surface and its bulk, and the formation of free radical species as well as bond formation.

• 대한방사선기술학회지:방사선기술과학
• /
• 제2권1호
• /
• pp.95-99
• /
• 1979

When the ${\gamma}-ray$ of average energy 375KeV emitted by Ir-192 is exposed to each film through lead foil with various thickness, the film sensitivity will be different according to the thickness of lead foil and film type. The results on the study, different density and sensitive ratio appeared depending on exposed time and film type, but was made on the following common points. 1. The effect of film sensitivity by the front lead foil showed rapid increase up to the thickness of more or less 0.03mm, and the thicker lead foil was decreased more in the thickness of about $0.05{\sim}0.09mm$. 2. The effect of film sensitivity by the back lead foil was increased up to around of $0.03{\sim}0.08mm$ thickness, the maximum sensitivity was obtained in the thickness of more than $0.03{\sim}0.08mm$ without any change in the above effect. 3. The sensitivity of front lead foil was higher than that of back lead foil in thin lead foil with about 0.127mm thickness, but the sensitivity of back lead foil was higher than that of front lead foil when thickness became thicker.

• Journal of Pharmaceutical Investigation
• /
• 제20권1호
• /
• pp.13-18
• /
• 1990

Hydrocortisone (HC) sustained-release suppositories were prepared by using a solid matrix of methacrylic acid-methacrylic acid methyl ester copolymer $(Eudragit\;L_{100}^{R}:\;EL)$ as a poorly water soluble carrier and polyethylene glycole 1540 (PEG) as an water soluble carrier. HC release rate was controlled by complexation with ${\beta}-cyclodextrin$ $({\beta}-CyD)$ which was confirmed by X-ray diffractometry, IR-spectroscopy and differential scanning calorimetry. Release rate of HC from the EL-PEG matrix suppositories decreased with increase of EL contents. The release rale from $HC-{\beta}-CyD$ complex decreased in the following order: $HC-{\beta}-CyD/PEG$ > HC/PEG > $HC-{\beta}-CyD/EL_{10%}-PEG$ > $HC/EL_{10%}-PEG$ > $HC-{\beta}-CyD/EL_{15%}-PEG$ > $HC/EL_{15%}-PEG$ > $HC-{\beta}-CyD/EL_{20%}-PEG$ > $HC/EL_{20%}-PEG$. The crystallinity of HC in polymer matrix was identified using X-ray diffractometer and the surface of matrix suppositories after release test was examined by scanning electron microscopy. The sustained release of HC from these matrix suppositories was attributed to the network structure of EL.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 하계학술대회 논문집 Vol.3 No.2
• /
• pp.813-816
• /
• 2002

We investigate the junction between CdZnTe and a variety of metals with the aim of determining whether the choice of metal can improve the performance of X-ray image detectors, in particular minimizing the dark current. The samples consist of $5{\mu}m$ thick CdZnTe with top electrodes formed from In, Al, and Au. For each metal, current transients following application of valtages from -10V to 10V are measured for up to 1 hour. We find that dark currents depending on the metal used. The current is controlled by hole injection at the metal-CdZnTe junction and there is consistent trend with the metal's work function possibly and it seems that metal to CdZnTe layer junction is ohmic contact.

• 대한전기학회논문지:시스템및제어부문D
• /
• 제55권7호
• /
• pp.313-318
• /
• 2006

An automatic sample centering system is underway at the protein crystallography beam line of the Pohang Light Source to improve the efficiency of the crystal screening process. A sample pin which contains a protein crystal is mounted on a goniometer head. Then the crystal should be moved to the center of X-ray beam by controlling the motorized goniometer to obtain diffraction data. Since the X-ray beam is located at the center of the image obtained from the CCD camera when the image of the sample pin is in focus, an auto-focusing algorithm is a very important part in the auto-sample-centering system. However the results of applying several well-known auto focusing algorithms directly to the images are not satisfactory owing to the following factors: misalignment of CCD camera, non-uniform cryo-stream in the background of the image and the supporter of the loop. The performance of an auto-focusing algorithm can be increased if the algorithm is applied to only the loop region identified. Non-uniform cryo-stream and a various illumination condition and a stain, which is shown in the image, are main obstacles to loop region identification. In this paper, a simple loop region identification algorithm, which can solve these problems, is proposed and the effective ness of the proposed scheme is shown by applying the auto-focusing algorithm to the loop region identified.

• 한국생산제조학회지
• /
• 제24권4호
• /
• pp.363-367
• /
• 2015

This paper reports on thermally adjusted graphene oxide (GO) as the hole transport layer (HTL) for organic light-emitting diodes (OLEDs). GO is generally not suitable for HTL of OLEDs because of intrinsic specific resistance. In this paper, the specific resistance of GO is adjusted by the thermal annealing process. The optimum specific resistance of HTL is found to be $10^2{\Omega}{\cdot}m$, and is defined by the maximum current efficiency of OLEDs, 2 cd/A. In addition, the reasons for specific resistance change are identified by x-ray photoelectron spectroscopy (XPS). First, the XPS results show that several functional groups of GO were detached by thermal energy, and the amount of epoxide changed substantially following the temperature. Second, the full width at half maximum (FWHM) of the C-C bond decreased during the process. That means the crystallinity of the graphene improved, which is the scientific basis for the change in specific resistance.