• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.28 no.1
• /
• pp.81-88
• /
• 1983

This experiment was conducted to study about influenced inorganic element contents of flag leaf and chaff with different nitrogen and silicate application in Jinan (sea level 303m). The recommended rate of fertilizer application above N 15kg/10a was poor for dry production increment in cold in July elevation and was demanded increment of silicate. In the elevation of cold in July high rates of nitrogen application produced more incomplete grain and a reduced cold tolerance. These effects were due to over-content of soluble nitrogen within flag leaf and disturbance of uptaking potassium and silicate. On the other hand, the application of silicate could increase yield by promoting resistance to cold- damage. The application of increasing level of nitrogen resulted in increasing the contents of total nitrogen and phosphate in both sterile and fertile glumes. The contents of potassium and calcium were the highest at the level of nitrogen 10 - 15kg/10a, but magnessium was rather high at low nitrogen levels. It is interesting that at any level of nitrogen, over 6% higher silicate contents were noted in the fertile chaff than in the sterile chaff. Application of increasing level of silicate fertilizer decreased total nitrogen contents, but increased the contents of phosphate, potassium. and silicate in the chaff. Increasing rate of silicate content by increasing silicate addition was remarkably higher in the fertile chaff than in the sterile chaff.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.144.2-144.2
• /
• 2016

Diamond-like carbon (DLC) coatings have been widely applied to the mechanical components, cutting tools due to properties of high hardness and wear resistance. Among them, hydrogenated amorphous carbon (a-C:H) coatings are well-known for their low friction properties, stable production of thin and thick film, they were reported to be easily worn away under high temperature. Non-hydrogenated tetrahedral amorphous carbon (ta-C) is an ideal for industrial applicability due to good thermal stability from high $sp^3$-bonding fraction ranging from 70 to 80 %. However, the large compressive stress of ta-C coating limits to apply thick ta-C coating. In this study, the thick ta-C coating was deposited onto Inconel alloy disk by the FCVA technique. The thickness of the ta-C coating was about $3.5{\mu}m$. The tribological behaviors of ta-C coated disks sliding against $Si_3N_4$ balls were examined under elevated temperature divided into 23, 100, 200 and $300^{\circ}C$. The range of temperature was setting up until peel off observed. The experimental results showed that the friction coefficient was decreased from 0.14 to 0.05 with increasing temperature up to $200^{\circ}C$. At $300^{\circ}C$, the friction coefficient was dramatically increased over 5,000 cycles and then delaminated. These phenomenon was summarized two kinds of reasons: (1) Thermal degradation and (2) graphitization of ta-C coating. At first, the reason of thermal degradation was demonstrated by wear rate calculation. The wear rate of ta-C coatings showed an increasing trend with elevated temperature. For investigation of relationship between hardness and graphitization, thick ta-C coatings(2, 3 and $5{\mu}m$) were additionally deposited. As the thickness of ta-C coating was increased, hardness decreased from 58 to 49 GPa, which means that graphitization was accelerated. Therefore, now we are trying to increase $sp^3$ fraction of ta-C coating and control the coating parameters for thermal stability of thick ta-C at high temperatures.

• Applied Chemistry for Engineering
• /
• v.17 no.3
• /
• pp.250-254
• /
• 2006

Reaction of $CO_2$ with $Li_{2}ZrO_{3}$ has been investigated in a TGA and the effects of $H_{2}$ and CO on the removal of $CO_{2}$ using $Li_{2}ZrO_{3}$ were evaluated in a packed bed reactor. The initial rate of $CO_{2}$ removal reaction of $Li_{2}ZrO_{3}$ increased with the increase of gas flow rate up to 100 mL/min and then was maintained, which implied the disappearance of the gas film resistance. The reaction of $CO_{2}$ with $Li_{2}ZrO_{3}$ took place as the first order and the range of optimum temperature was found to be about $500{\sim}600^{\circ}C$. XRD and SEM analysis showed the formation of crystalline $Li_{2}ZrO_{3}$ and porous $Li_{2}ZrO_{3}$/$ZrO_{2}$. The presence of $H_{2}$ did not affect the adsorption of $CO_2$ with $Li_2ZrO_3$. On the other hand, CO inhibited the sorption of $CO_{2}$ into $Li_{2}CO_{3}$(L) on $Li_{2}ZrO_{3}$.

• Journal of the Korea Institute of Building Construction
• /
• v.20 no.5
• /
• pp.391-397
• /
• 2020

This study is to compare and analyze the strength, drying shrinkage and carbonation properties of lightweight aggregate mortar using recycling water as prewetting water and mixing water. The flow, compressive strength, split tensile strength, drying shrinkage and carbonation depth of lightweight aggregate mortar with recycling water were measured. As test results, the mortar flow was similar in all mixes regardless of the recycling water content. The compresseive strength of the RW5 mix with 5% recycling water as prewetting water and mixing water was the highest value, about 53.9 MPa after 28 days. In addition, the tensile strength of lightweight mortar was about 3.4 to 3.8 MPa, indicating 7 to 9% of the compressive strength value regardless of recycling water content. In the case of drying shrinkage, the RW2.5 mix using 2.5% recycling water showed the lowest shrinkage rate as about 0.107% at 56 days. The drying shrinkage of the plain mix without recycling water was relatively higher than the RW2.5 and RW5 mix. The RW5 mix showed lowest carbonation depth compared to other mixes. In this study, the RW5 lightweight aggregate mortar with 5% recycling water exhibits excellent compressive strength and carbonation resistance. Therefore, it is considered that if the recycling water, a by-product of the concrete industry, is properly used as prewetting water and mixing water of lightweight mortar and concrete, it will be possible to increase the recycling rate of the by-product and contribute to improve the property of lightweitht aggregate mortar and concrete.

• Korean Journal of Environmental Agriculture
• /
• v.42 no.4
• /
• pp.346-352
• /
• 2023

Cadusafos, an organophosphorus insecticide, has been commonly used against various pests worldwide. Organophosphorus pesticides have shorter half-lives and lower toxicities than organochlorine pesticides. However, excessive use of Cadusafos can increase pest resistance and issues with acetylcholine biomagnification, potentially resulting in human toxicity. In this study, we investigated the effect of a Cadusafos-degrading microbial agent (CDMA) prepared using Sphingobium sp. Cam5-1, which was previously reported to effectively degrade residual Cadusafos in soil. Experiments were conducted under both controlled laboratory and greenhouse field conditions. Under laboratory conditions, CDMA (10⁶ cfu/g soil application rate) decomposed 97% of Cadusafos in the soil in the untreated control after 21 days. Additionally, when CDMA (10⁶ cfu/g soil) was mixed with quicklime, 99% of Cadusafos was decomposed within 3 days. Under greenhouse field conditions, the combined effect of CDMA (10⁶ cfu/g soil) and quicklime was not observed. However, CDMA (10⁶ cfu/g soil) application alone was capable of decomposing 91% of Cadusafos after 3 days. These results indicate that CDMA can effectively decompose high residual levels of Cadusafos in soils under field conditions using a low inoculum rate.

• Journal of Magnetics
• /
• v.9 no.1
• /
• pp.17-22
• /
• 2004

We studied the magnetotransport properties of tunnel junctions with AlO and AlN barriers fabricated using microwave-excited plasma. The plasma nitridation process provided wider controllability than the plasma oxidization for the formation of MTJs with ultra-thin insulating layer, because of the slow nitriding rate of metal Al layers, comparing with the oxidizing rate of them. High tunnel magnetoresistance (TMR) ratios of 49 and 44% with respective resistance-area product $(R{\times}A) of 3 {\times} 10^4 and 6 {\times} 10^3 {\Omega}{\mu}m^2$ were obtained in the Co-Fe/Al-N/Co-Fe MTJs. We conclude that AlN is a hopeful barrier material to realize MTJs with high TMR ratio and low $R{\times}A$ for high performance MRAM cells. In addition, in order to clarify the annealing temperature dependence of TMR, the local transport properties were measured for Ta $50{\AA} /Cu 200 {\AA}/Ta 50 {\AA}/Ni_{76}Fe_{24} 20 {\AA}/Cu 50 {\AA}/Mn_{75}Ir_{25} 100 {\AA}/Co_{71}Fe_{29} 40 {\AA}/Al-O$ junction with $d_{Al}= 8 {\AA} and P_{O2}{\times}t_{0X}/ = 8.4 {\times} 10^4$ at various temperatures. The current histogram statistically calculated from the electrical current image was well in accord with the fitting result considering the Gaussian distribution and Fowler-Nordheim equation. After annealing at $340^{\circ}C$, where the TMR ratio of the corresponding MTJ had the maximum value of 44%, the average barrier height increased to 1.12 eV and its standard deviation decreased to 0.1 eV. The increase of TMR ratio after annealing could be well explained by the enhancement of the average barrier height and the reduction of its fluctuation.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.11
• /
• pp.529-535
• /
• 2018

The range extender vehicle runs on a mechanism that allows the small power generation engine to start in the most efficient specific operating range to charge the battery and extend the mileage. In this study, we developed a step motor type intake air supply system that replaces existing throttle body system to develop a simple low cost control logic system. The system was applied to the existing base engine, and in order to improve the performance by increasing the amount of intake air, the effect of changing the length of the intake and exhaust manifold was experimentally examined. As a result, the Type B intake air control actuator operated by one step motor showed higher performance than the Type A in all the operation region, but the performance was lower than that of the base engine due to the increase of flow resistance. To improve this, it was confirmed that the engine performance was improved at both speeds of 2200rpm and 4300rpm when the 140mm adapter was installed in the intake manifold and when the newly designed 70mm exhaust manifold was applied. Through this process, high - precision operation control was realized by connecting the generator load to the optimized engine for the range extender electric vehicle. Experimental results showed that the speed change rate was within ${\pm}2.5%$ at 2200rpm in 1st stage and 4300rpm in 2nd stage and the speed follow-up result of 610 rpm/s was obtained when the speed was increased from 2200rpm to 4300rpm.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.7 no.1
• /
• pp.139-144
• /
• 1969

1. In order to obtain useful mutants such as early maturity, resistance to lodging, high protein and oil content, and capability of high yield, dormant seeds of two soybean varieties, Jang Dan Baik Mok and Clark, were treated with ${\gamma}$-ray, Ethyl Methane Sulfonate(EMS), Ethylene Imine(EI)and combinations of ${\gamma}$-ray and EMS or EI. 2. The germination rate and survival rate in a variety Jang Dan Baik Mok were significantly decreased with ${\gamma}$-ray treatment while it was not the same in the Clark variety. A significant decrease for seedling height measured at 14 and 21 days after sowing was found with the increase of ${\gamma}$-ray dose in both varieties. 3. Germination rates in both varieties were significantly decreased as EI concentration increases, particularly severe damage in germination was observed at 0.008 Mo. concentration. Germination rate damages were found with EMS concentration increases in the variety Jang Dan Baik Mok while no regular responses in seedling height were observed in the variety Clark. 4. Germination rate was significantly lowered with the combined treatment of EMS and ${\gamma}$-ray 24KR than that of EMS alone. In the treatments of ${\gamma}$-ray with three levels of EI concentration, the combined treatments except 24KR+EI 0.002 Mol. resulted in better germination than of EI alone. In both varieties, significant reduction in seedling height was observed in the combined treatments of ${\gamma}$-ray with various concentrations of EMS, whereas stimulation effect on seedling height was found with treatment of ${\gamma}$-ray EI +0.08Mol. 5. Germination rate, survival rate, and plant height as criteria of radio sensitivity, variety Jang Dan Baik Mok is moze sensitive to ${\gamma}$-ray, EMS, and EI than the variety Clark, and the varietal difference in responsibility to mutagen may be due to the genetic-constitution of the varieties.

• Journal of Ginseng Research
• /
• v.36 no.4
• /
• pp.461-468
• /
• 2012

In this study, photosynthetic parameters such as the net photosynthesis rate, stomatal conductance, intercellular $CO_2$ concentration, and transpiration rate were examined in selected ginseng varieties and/or lines that are resistant (Yunpoong, HTIR 1, HTIR 2, and HTIR 3) and susceptible (Chunpoong) to high temperature injury (HTI). The net photosynthesis rate increased with the increase in the light intensity in all the HTI-resistant and -susceptible ginseng lines with a light saturation point of $200\;{\mu}mol\;m^{-2}s^{-1}$, except for Yunpoong that had a light saturation point of $400\;{\mu}mol\;m^{-2}s^{-1}$. At the light saturation point, the net photosynthesis rate in July was highest in HTIR 3, at $4.2\;{\mu}mol\;CO_2\;m^{-2}s^{-1}$, and was lowest in Yunpoong, HTIR 1, Chunpoong, and HTIR 2, in that order, at 1.9 to $3.7\;{\mu}mol\;CO_2\;m^{-2}s^{-1}$. The net photosynthesis rate in August was highest in Yunpoong at $5.9\;{\mu}mol\;CO_2\;m^{-2}s^{-1}$, and lowest in HTIR 1 and HTIR 3 ($4.5\;{\mu}mol\;CO_2\;m^{-2}s^{-1}$) and in other lines, in that order, at 2.8 to $2.9\;{\mu}mol\;CO_2\;m^{-2}s^{-1}$. The stomatal conductance in July was highest in HTIR 3 (0.055 mol $H_2O\;m^{-2}s^{-1}$) and Yunpoong, Chunpoong, HTIR 1, and HTIR 2 were 0.038, 0.037, 0.031, and 0.017 in that orders. In August, meanwhile, HTIR 1 showed the highest as 0.075, and followed by HTIR 3, Chungpoong, and HTIR 2 with 0.070, 0.047, and 0.023, respectively. The intercellular $CO_2$ concentration at the light saturation point in July and August was much lower in HTIR 2 at 139 and $185\;{\mu}mol\;mol^{-1}$ than in the other ginseng lines at 217 to 257 and 274 to $287\;{\mu}mol\;mol^{-1}$, respectively. The transpiration rate in July and August was higher in the HTI-resistant lines of Yunpoong, HTIR 1, and/or HTIR 3 at 0.83 to 1.03 and 1.67 to 2.10 mol $H_2O\;m^{-2}s^{-1}$ than in the other ginseng lines at 0.27 to 0.79 mol $H_2O\;m^{-2}s^{-1}$ and 0.51-1.65 mol $H_2O\;m^{-2}s^{-1}$, respectively. Conclusively, all the photosynthetic parameters that were examined in this study were generally higher in the HTI-resistant ginseng lines than in the HTI-susceptible lines, except for HTIR 2, and were much higher in August than in July, especially in the resistant ginseng lines. All these results can be used to provide basic information for the selection of HTI-resistant ginseng lines and the application of cultural practices that are efficient for ginseng growth, based on the photosynthetic characteristics of the lines.

• Tuberculosis and Respiratory Diseases
• /
• v.61 no.1
• /
• pp.13-19
• /
• 2006

Background: Acinetobacter baumannii has emerged as an important nosocomial pathogen worldwide. The incidence of these infections has recently begun to increase. The mortality rate associated with these infections is high (bacteremia; 52%, pneumonia: 23%~73%) and multidrug resistance has been reported. For the effective control of multidrug-resistant Acinetobacter baumannii(MDR-AB), the impact of these organisms in clinical practice should be determined. This study compared the clinical characteristics, mortality and morbidity of Acinetobacter nosocomial pneumonia between MDR strain and non-MDR strain. Methods: From Jan. 1, 2002 to Nov. 1. 2004, 47 adult patients with Acinetobacter nosocomial pneumonia in Chuncheon Sacred Heart Hospital were recruited and analyzed retrospectively. MDR-AB was defined as showing in vitro resistance to all commercially available antibiotics against A. baumannii. Results: There were 47 patients with Acinetobacter nosocomial pneumonia. MDR-AB and non MDR-AB was the cause of the pneumonia in 17 and 30 patients, respectively. Mean age of the former was $69{\pm}11$ years old and the latter was $70{\pm}13$ years old. The mean APCHE II score, ICU days and mortality were not different between the two groups ($16.1{\pm}5.4$ vs. $14.9{\pm}4.8$, P=0.43, $25.1{\pm}13.6$ vs. $39.1{\pm}31.0$, P=0.2, 58.8% vs. 40%, P=0.21). Conclusion: There are no significant differences in mortality and morbidity between MDR and non-MDR Acinetobacter baumannii. The mortality of the two groups is surprisingly high, therefore proper infection control practices are essential.