• 한국환경복원기술학회지
• /
• 제4권3호
• /
• pp.38-48
• /
• 2001

A wetland is an ecosystem which is the most useful and highly-energetic transition area. This study has been carried out to develop the wetland function assessment methods and apply on the natural wetlands (Mul-young-ari wetland in Jeju-island and Bangdong wetland in Taejon Metropolitan city) using RAM (Rapid Assessment Method). The RAM is useful method for assessing the wetland functions in terms of general functions acquired by once or twice onsite surveying. Eight functions of 2-12 variables each are analyzed for assessing the wetland functions. The results are as follows : 1) The conservation values of two wetlands are "High". 2) In Mul-young-ari wetland, such functions as groundwater discharge, floral diversity and wildlife habitat, shoreline/stream bank protection are relatively high, but some functions such as flood/storm water storage, aesthetics and recreation are "Moderate" - "High". 3) In Bangdong wetland, such functions as floral diversity and wildlife habitat, groundwater discharge, flood/storm water storage, aesthetics and recreation are high, and another functions are "Moderate" - "High". The taxonomy of this study stems from assessing functions of inland wetlands using indices of RAM. So It is needed that consequent studies are to be performed with verifying the variables and indices.

• Journal of Mechanical Science and Technology
• /
• 제18권9호
• /
• pp.1623-1629
• /
• 2004

The objective of this study is the rapid bulk combustion of mixture in a constant volume chamber with a tiny sub-chamber. Some narrow passage holes were arranged to induce simultaneous multi-point ignition in the main chamber by jet of burned and unburned gases including radicals from the sub-chamber, and the equivalence ratios of pre-mixture in the main chamber and the sub-chamber were the same. The principal factors of the Radical Induced Auto-Ignition (RIAI) method are the diameter of the passage holes and the volume of sub-chamber. The relationship between the sub-chamber and diameter of passage hole was represented by the ratios of sub-chamber volume to passage hole volume. The ratios are non-dimensional coefficients for sub-chamber characteristics. As a result, the RIAI method reduced the combustion period, which expanded the lean limit in comparison with SI method.

• Journal of Microbiology and Biotechnology
• /
• 제17권3호
• /
• pp.516-519
• /
• 2007

Enterobacter sakazakii is an emerging food pathogen, which induces severe meningitis and sepsis in neonates and infants, with a high fatality rate. The disease is generally associated with the ingestion of contaminated infant formula. In this study, we describe the development of a real-time PCR protocol to identify E. sakazakii using a TaqMan probe, predicated on the nucleotide sequence data of the 168 rRNA gene obtained from a variety of pathogens. To detect E. sakazakii, four primer sets and one probe were designed. Five strains of E. sakazakii and 28 non-E. sakazakii bacterial strains were used in order to ensure the accuracy of detection. The PCR protocol successfully identified all of the E. sakazakii strains, whereas the 28 non-E. sakazakii strains were not detected by this method. The detection limits of this method for E. sakazakii cells and purified genomic DNA were 2.3 CFU/ assay and 100 fg/assay, respectively. These findings suggest that our newly developed TaqMan real-time PCR method should prove to be a rapid, sensitive, and quantitative method for the detection of E. sakazakii.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2017년도 춘계 학술논문 발표대회
• /
• pp.167-168
• /
• 2017

With the recent increase in demand for construction there has been an increase in the use of the raw material cement when mixing concrete; managing quality of cement powder, therefore, is most important. Therefore this study sought at first to develop a rapid appraisal using the Hydrometer method researched previously, for it was thought that when suspending cement in a solution and applying the Hydrometer method to it the temperature changes in the solution would have a great effect on the density value of the Hydrometer method; yet there has been no report of such influence factors. Therefore after analyzing the influence factors that the type of suspending solution and changes in temperature could have on rapid appraisal of fineness, using the Hydrometer method, this study was able to determine that using water at 20℃ was the most appropriate, and with every temperature increase of 10℃ the value of fineness should also be increased above or below 7% as well.

• 한국식품영양학회지
• /
• 제25권2호
• /
• pp.393-397
• /
• 2012

본 연구에서는 온도 변화 방법을 이용하여 조미계란을 신속하게 제조하기 위한 가염방법을 개발하고자 하였다. 먼저 염지액의 농도에 따른 계란 내부로 염분의 침투 효과를 분석한 결과, 20, 30 및 40%의 염지액에서 2시간 동안 염지시킨 각각의 계란내 염분 함량은 0.51, 0.57 및 0.60%를 나타내어 농도가 높아질수록 침투효과가 향상되는 것을 확인할 수 있었으며, 고온에서 저온으로 계란의 온도 변화를 유도한 온도변화 방법을 적용한 경우 2시간 동안 계란내 염분 함량이 각각 0.49, 0.56 및 0.70%를 나타내어 40%의 염지액에서 염분의 침투 효과가 향상되었다. 그리고 4, 5 및 7 MPa의 압력을 가하여 40%의 염지액으로 15분간 염지한 경우, 각각 1.14, 1.36 및 1.45%의 염분 함량을 나타내어 대기압 조건에서 침투시킨 결과보다 빠르게 침투되었다. 온도 변화 방법을 적용하여 4, 5 및 7 MPa의 압력을 가하여 40%의 염지액으로 15분간 염지한 경우 각각 1.52, 1.62 및 1.66%의 염분 함량을 나타내어 온도 변화 방법에 의해 침투 효과가 향상됨을 확인할 수 있었다. 이는 계란의 온도 변화 방법이 계란 내부 난막의 수축효과로 외부 염분의 흡입을 유도하였기 때문으로 생각되며, 조미계란을 신속하게 제조하기 위한 가염 방법으로 온도 변화 방법의 적용이 매우 효과적이라고 생각된다.

• 한국주조공학회지
• /
• 제39권2호
• /
• pp.26-31
• /
• 2019

In this study, the mechanical characteristics and microstructure of hypereutectic Al-17Si-5Fe extruded alloys prepared by a rapid solidification process (RSP) were investigated. The hypereutectic Al alloy was fabricated by means of RSP and permanent casting. For RSP, the Al alloy melted at $920^{\circ}C$, cooling the specimens at a rate of $10^6^{\circ}C/s$ when the RSP was used, thus allowing the refining of primary Si particles more than when using permanent casting, at a rate of about 91%. We tested an extrusion RSP billet and a permanent-cast billet. Before the hot-extrusion process, heating to $450^{\circ}C$ took place for one hour. The samples were then hotextruded with a condition of extrusion ratio of 27 and a ram speed of 0.5 mm/s. Microstructural analyses of the extruded RSP method and the permanent casting method were carried out with OM and SEM-EDS mapping. The mechanical properties in both cases were evaluated by Vickers micro-hardness, wear resistance and tensile tests. It was found that when hypereutectic Al-17Si-5Fe alloys were fabricated by a rapid solidification method, it becomes possible to refine Si and intermetallic compounds. During the preparation of the hypereutectic Al-17Si-5Fe alloy by the rapid solidification method, the pressure of the melting crucible was low, and at faster drum speeds, smaller grain alloy flakes could be produced. Hot extrusion of the hypereutectic Al-17Si-5Fe alloy during the rapid solidification method required higher pressure levels than hot extrusion of the permanent mold-casted alloy. However, it was possible to produce an extruded material with a better surface than that of the hot extruded material processed by permanent mold casting.

• 한국자동차공학회논문집
• /
• 제3권1호
• /
• pp.143-154
• /
• 1995

This study investigates the response characteristics of a four-cylinder four-stroke turbocharged diesel engine by using computer simulation and experiments when a rapid acceleration is applied to the fuelpump rack. In the theoretical analysis, linearization method is used to avoid the difficulty on the complex nonlinear functions. Comppressor exit pressure, pressure and temperature of turbine inlet, and turbocharger speed are chosen as the independent variables of transfer functions which represent the dynamic characteristics of the turbocharger system, and expressed as the functions with respect to the time. Experiments on the same eigine system are also carried out to prove the validity of theoretical study. Further, this study carried an experiment for improving transient response performance by injecting air into the inlet manifold under the rapid accelerating conditions. The effects of air injection on the response performances are also represented at varying conditions such as injection pressure, injection period, accelerating rate, accelerating time, engine speed and load.

• 한국정밀공학회지
• /
• 제13권10호
• /
• pp.46-55
• /
• 1996

As industrial standard data, the STL format which approximates three dimensional CAD model to triangular facets, is used for RP(Rapid Prototyping) system in recent days. Because most RP system take the only form of two dimensional line segments as an input stream inspite of its imperfectness while converting into STL format, a CAD model is converted into a standard industrial format which is composed of many triangular facets. The error verifying process is composed of four main steps, and these are 1) Remove facets with two or more vertices equal to each other. 2) Fix overlapping error such as more than three facets adjacent to anedge. 3) Fill holes in the mesh by using Delaunay triangulation method. 4) Correct the wrong direction and normal vectors. This paper is concerned with serching the mentioned errors in advance and modifying them.

• 한국관개배수논문집
• /
• 제21권1호
• /
• pp.45-54
• /
• 2014

In this study, Agricultural Infrastructures of Shincheon-gun in North Korea are investigated using Kompsat-2 and RapidEye satellite imagery. Target agricultural infrastructures are agricultural landuse, irrigation and drainage canals, dammed pools for irrigation and pumping stations. KOMPSAT-2 satellite imagery are use to investigate agricultural hydraulic structures and agricultural landuse are investigated by RapidEye Imagery. Geometric correction are performed using 28 GCP and QUAC method are used for atmospherical correction in all imagery. ISODATA clustering and naked-eye classification method are used for extracting agricultural hydraulic structures and Object-based analysis is applied to classifying the agricultural landuse. Extraction results of agricultural hydraulic structures and agricultural are presented and we suggest the applicability of satellite imagery to investigate agricultural infrastructures in North Korea.

• 한국동물위생학회지
• /
• 제29권3호
• /
• pp.339-346
• /
• 2006

Semi-micro-HPLC using a column-switching technique was developed for simultaneous determination of vitamin A and E contents in infant formula. Vitamin A and E were extracted by PDA - HPLC with reversed phase column using organic solvent and their contents in Certified Reference Material (CRM) and infant formula were determined and compared with hydrolysis method and rapid extraction. Developed method has many advantages of simple and rapid sample preparation and simultaneous determination of vitamin A and E by micro-HPLC using reversed phase column.