• Proceedings of the KSR Conference
• /
• 2011.05a
• /
• pp.690-696
• /
• 2011

A number of conventional railway bridge is more than 2600. Non-ballast plate girder bridge is about 700 and this is 27% of all bridge numbers. Non-ballast plate girder has advantages that self load is more lighter than moving load and construction cost is more inexpensive than concrete bridge. But non-ballast plate girder has disadvantages that vibration and noise is bigger than concrete bridge. This study had analyzed behavior of non-ballast plate girder according to the arrangement of supports and driving conditions to review the proper arrangement of support. Measurements were performed in single line and disel locomotive of 7400type were used as test vehicle. The vehicle's driving conditions are as follows; Change of driving direction, Constant speed driving, Deceleration driving, Acceleration driving. Main measurement contents were horizontal displacement and vertical vibration acceleration in girder of vicinity support. Results of measurement are as follows; In case that a vehicle drives from fixed support to movable support, vertical vibration acceleration of the girder was smaller than opposition case.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.5 no.2
• /
• pp.163-174
• /
• 2001

This paper is to study the characteristics of axial force behavior that operates to the part of turnout when it makes the turnout and the continuous welded rail unifying. The study is to model by using the 50kgN rail No. 15 turnout used in the domestic national railway and the UIC60 rail No. 18 turnout used in the rapid transit railway as the finite elements for analyzing the axial force behavior of the turnout by the continuous welded rail. It is to analyze the characteristics of behavior according to the change of creep resistance, ballast resistance and the change of parameter valuables of heel joint by the axial force simulation in making the continuous welded rail and then, it is to present the result. As the result of research on the parameter valuables through the analysis, it shows that the maximum axial force of turnout by the continuous welded rail are largely subordinated to the maximum resistance of heel joint and the fitting devices than the ballast resistance. Also it shows that the maximum axial force produced changes a lot according to the characteristics of creep resistance of the fitting part and the ballast resistance.

• Proceedings of the KSR Conference
• /
• 2005.05a
• /
• pp.597-603
• /
• 2005

The remediation of railroad contaminated soil is gaining wide attention, recently. In railroad field, modification of diesel supply field, equipment of roll pad, FRP panel, and iron pannel under diesel locomotive storages are used for the prevention of contamination expansions. However, cheap and efficient remediation technology has not been suggested yet. In this study, the contaminated ballast was remediated by blasting technology. Because the contaminants mainly resides on the surface of ballast, blasting these contaminants make it available to recycle the ballast. We carried out the remediation of oil-contaminated ballasts using the blasting technology, and we could remediate them nicely. This technology is expected to be used for the cheap and quick remediation of contaminated ballast.

• Proceedings of the KSR Conference
• /
• 2007.11a
• /
• pp.1071-1076
• /
• 2007

In high-speed line, at some part of the track which rubber ballast-mat installed, track irregularity grew rapidly and affected riding comfort and train running stability. It is urgently requested to establish counter-measures which can be applied to track under operation. To do this, it is very important to analysis the origin of that phenomenon before. Track support stiffness is an essential factor for evaluating track condition. Sudden changes of support stiffness along track occur instability of train and bad riding comfort. Preventing sudden changes of track support stiffness is a key technique in high-speed track maintenance. Besides the sudden changes, the magnitude itself also significantly affects track and train. Low stiffness of ballast-mat makes ballast acceleration area wider. And it may accelerate track irregularity growth. So, the stiffness should be limited. To calculate track stiffness, measuring load and displacement on track is needed. In this study, the behavior of the track which rubber ballast-mat installed was measured and analyzed to understand the origin of rapid growth of it.

• Proceedings of the KSR Conference
• /
• 2007.11a
• /
• pp.1386-1391
• /
• 2007

The ballast gravels are often contaminated by various pollutants, like diesel fuel, lubricants, and heavy metals. Especially, the gravels near the switching are apt to be polluted by the lubricant. Because this lubricant can pollute the soil of track, the contaminated ballast gravels should be cleaned immediately. In this study, a physical desorption method was used to remove the oil contaminants from the surface of the ballast gravels. Thermosetting resin was used as a media for physical remediation of ballast gravels. The total petroleum hydrocarbon of the gravels was monitored over time. In addition, scanning electron microscopic images were obtained to observe the removal of the oily pollutants from the surface of the gravels.

• Proceedings of the KSR Conference
• /
• 2003.10c
• /
• pp.275-280
• /
• 2003

The Korean high speed train is designed to run at very high speed such as 350km/h. At this time, ballast in roadbed is dispersed by high speed air flow and this hits the substructure of the train. It becomes the factor of damaging the train. To investigate the main factor and possibility of ballast dispersion, the substructure flow is measured by Kiel-Probe Array System at G7 train experiment. And the wind tunnel experiment is performed with ballast in our research. Also CFD analysis is performed by assuming that the flow field is 2D and using simple shaped cross-tie and flat substructure of the train. By comparing the experimental results and CFD analysis, the accuracy of the analysis is checked. They will become the basic research data for the analysis and optimization of train substructure to prevent the ballast dispersion.

• Proceedings of the KSR Conference
• /
• 2006.11b
• /
• pp.484-493
• /
• 2006

This paper is presented the test results to evaluate the healthiness of the ballast in subway. The test includes the dynamic load test in servicing Line the screen classification test of aggregates and the wear test. From the results, the aspect and the property of the ballast are evaluated. The dynamic load tests the relationship between the deterioration of the ballast and the fluctuation of loads. The assesexplain sment of impact factor based on the field test results in a good property of test blocks is proposed.

• Proceedings of the KSR Conference
• /
• 2007.05a
• /
• pp.303-310
• /
• 2007

In this paper, the correlation between the vibration characteristics of the track components and the parameters affecting the vibration is analysed. To do it, the accelerations of each track component such as rails, sleepers and ballast are measured in Kyong-Bu high-speed railway lines. The RMS values of the measured data are calculated and the corrugation, the track irregularity and the pad stiffness are considered as the parameters in the viewpoint of track. By using the linear regression, the correlation coefficient is calculated to analyse the relationship. The parameter whose correlation coefficient is more than 0.7 is considered as the major one. Also, the 1/3 Octave analysis is calculated to analyse the dominant frequency band of the vibrations of the track components.

• Proceedings of the KSR Conference
• /
• 2010.06a
• /
• pp.633-639
• /
• 2010

Cold area in korea, railway roadbed and gravel ballast was occurred frost-heaving. So during winter, track was rising and during thaw, track was sinking. In order to prevent the damage of frost-heaving, we have applied a few countermeasures which are circumfusion of calcium chloride and replacement of gravel ballast method. This countermeasures effect is feeble, not continuous and not eco-friendly. This study suggested that we use wasted tire-chips in frost-heaving area and considered appropriate new method to maintenance. This method was named "A Method of Wasted Tire-Chips Post". To prove effect of this method, we have tested in laboratory and field. The result of frost-heaving-ratio field test was decreased frost-heaving-ratio about 50% using "A Method of Wasted Tire-Chips Post".

• Proceedings of the KSR Conference
• /
• 2002.10b
• /
• pp.1041-1046
• /
• 2002

A railway open deck plate girder bridge without ballast should support relatively heavier vehicle loads compared with its self-weight. For such a reason, actual dynamic response of the bridge is considerably differing with normal prediction because additional masses added from vehicle to a bridge have an effect on the dynamic characteristics of the bridge. These differences affect to the estimation of a natural frequency change that adopted for one of the evaluation technique of strength decrease, and these make trouble to the analysis of a natural frequency from the field test data that measured at the bridge subjected to a running vehicle. In this study, classification of mass participation ratio for each component of open deck plate girder bridge without ballast and the comparison according to the change of vibration characteristics for the case of subjected to a running vehicle were accomplished.