• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.5
• /
• pp.613-623
• /
• 2012

In this paper, we present an ultra miniaturized voltage tuned oscillator, with HMIC-type amplifier and phase shifter, using LTCC artificial dielectric resonator. ADR which consists of periodic conductor patterns and stacked layers has a smaller size than a dielectric resonator. The design specification of ADR is obtained from the design goal of oscillator. The structure of the ADR with a stacked circular disk type is chosen. The resonance characteristic, physical dimension and stack number are analyzed. For miniaturization of ADRO, the ADR is internally implemented at the upper part of the LTCC substrate and the other circuits, which are amplifier and phase shifter are integrated at the bottom side respectively. The fabricated ADRO has ultra small size of $13{\times}13{\times}3mm^3$ and is a SMT type. The designed ADRO satisfies the open-loop oscillation condition at the design frequency. As a results, the oscillation frequency range is 2.025~2.108 GHz at a tuning voltage of 0~5 V. The phase noise is $-109{\pm}4$ dBc/Hz at 100 kHz offset frequency and the power is $6.8{\pm}0.2$ dBm. The power frequency tuning normalized figure of merit is -30.88 dB.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.26 no.11B
• /
• pp.1501-1509
• /
• 2001

Recently, the use of wireless communication systems has been rapidly increasing, which results in a difficult problem in efficient control of limited frequency resources. As a way of solving this problem, the ultra wideband time hopping impulse radio system attracts much attention. The impulse radio system communicates pulse position modulated data using Gaussian monocycle pulses of very short duration less than 1 nsec. Thus the transmitted signal has very low power spectral density and ultra wide bandwidth from near D.C. to a few GHz. It is blown that it hardly interferes with the existing communication systems because of its very low power spectral density. The purpose of this paper is to characterize multipath propagation of the impulse radio signal and to evaluate the performance of the correlator-based receiver for the multipath environments. In this paper, we consider the deterministic two-path model and the statistical indoor multipath model of Saleh and Valenzuela. For the two-path model the output of the correlator with the ideal reference waveform varies according to the relative difference between the indirect path delay and the time interval of PPM, and to the indirect path gains. In addition, the characteristics of bit error rates is measured for the two models through computer simulation. The simulation results indicate that the performance of the impulse radio system depends both on the relative difference between the indirect path delay and the time interval of PPM, and on the indirect path gains. Furthermore, it is observed that the reference signal designed for the AWGN channel can not be applied to the multipath channels.

• IEIE Transactions on Smart Processing and Computing
• /
• v.4 no.5
• /
• pp.371-378
• /
• 2015

In this paper, a different type of pulse width modulation (PWM) control scheme for a buck converter is introduced. The proposed buck converter uses PWM with frequency hopping and a low quiescent.current low dropout (LDO) voltage regulator with a power supply rejection ratio enhancer to reduce high spurs, harmonics and output voltage ripples. The low quiescent.current LDO voltage regulator is not described in this paper. A three-bit binary-to-thermometer decoder scheme and voltage ripple controller (VRC) is implemented to achieve low voltage ripple less than 3mV to increase the efficiency of the buck converter. An internal clock that is synchronized to the internal switching frequency is used to set the hopping rate. A center frequency of 2.5MHz was chosen because of the bluetooth low energy (BLE) application. This proposed DC-DC buck converter is available for low-current noise-sensitive loads such as BLE and radio frequency loads in portable communications devices. Thus, a high-efficiency and low-voltage ripple is required. This results in a less than 2% drop in the regulator's efficiency, and a less than 3mV voltage ripple, with -26 dBm peak spur reduction operating in the buck converter.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.4 no.3
• /
• pp.595-602
• /
• 2000

This paper is aimed at developing an location tracking system of mobile station based on currently available mobile communication network or mobile Phone and PCS(Personal Communication System). When the location tracking of mobile stations is in services, Emergency-119, all of crime investigation, effective urban traffic management and the safety protection of Alzheimer＇s patients can be available. In order to track the location of the mobile and base station, assumption in this paper is to use the statistic characteristics of LOS when modeling the standard noise in case that radio path is LNOS environment. The standard variation of the standard noise is $\pm150$. First, location is estimated by the positioning algorithms of TOA and TDOA and compared each other. Second, after canceling the standard noise by Kalman filter, location is estimated by the above two positioning algorithms. Finally, the location by the Kalman filter and two positioning algorithms is estimated by smoothing method. As a result, 2 dimensional average location error is imvoved by 51.2m in TOA and 34.8m in TDOA when Kalman filer and two positioning algorithms are used, compared with the two positioning algorithm used. And there is 3 more meter improvement after smoothing than Kalman filer and two positioning algorithms used.

• The Journal of the Korea Contents Association
• /
• v.6 no.4
• /
• pp.1-10
• /
• 2006

In this paper, a broadband RF module is designed and tested for 2.4GHz band applications. The RF module is composed of a low noise amplifier (LNA) with a three stage amplifier, a single ended gate mixer, matching circuits, a hairpin line band pass filter and a Chebyshev low pass filter to convert the radio frequency (RF) into the intermediate frequency (IF). The LNA has a high gain and stability, and the single ended gate mixer has a high conversion gain and wide dynamic range. In the analysis of the broadband RF module, the composite harmonic balance technique is used to analyze the operating characteristics of an RF module circuit. The RF module has a 55.2dB conversion gain with a 1.54dB low noise figure, $-120{\sim}-60dBm$ wide RF power dynamic range, -60dBm low harmonic spectrum and a good isolation factor among the RF, IF, and local oscillator (LO) ports.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.8
• /
• pp.3053-3059
• /
• 2010

In DS-CDMA method, Mobile Stations own jointly one radio channel and are made to use a PN code (Pseudo-Noise Code) for the purpose of minimize interference. However, corelation value of PN code is one when time delay is zero but the corelation value is 1 / N when time delay is not 0. Therefore corelation characteristic does not fully attained. As a result, when the user increase, the performance degradation and system capacity problem will be able to occur by interference among users. In this paper, the PN code has ideally self corelation. It was proved that PN code could depress interference from other users in multiple access system.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.28 no.12
• /
• pp.941-947
• /
• 2017

This paper reports a fractional-N phase-locked-loop(PLL) frequency synthesizer that is implemented in a $0.35-{\mu}m$ standard CMOS process and generates a quadrature signal for an FRS terminal. The synthesizer consists of a voltage-controlled oscillator(VCO), a charge pump(CP), loop filter(LF), a phase frequency detector(PFD), and a frequency divider. The VCO has been designed with an LC resonant circuit to provide better phase noise and power characteristics, and the CP is designed to be able to adjust the pumping current according to the PFD output. The frequency divider has been designed by a 16-divider pre-scaler and fractional-N divider based on the third delta-sigma modulator($3^{rd}$ DSM). The LF is a third-order RC filter. The measured results show that the proposed device has a dynamic frequency range of 460~510 MHz and -3.86 dBm radio-frequency output power. The phase noise of the output signal is -94.8 dBc/Hz, and the lock-in time is $300{\mu}s$.

• Asian-Australasian Journal of Animal Sciences
• /
• v.18 no.6
• /
• pp.868-872
• /
• 2005

Individual management of the animal is the first step towards reaching the goal of precision livestock farming that aids animal welfare. Accurate recognition of each individual animal is important for precise management. Electronic identification of cattle, usually referred to as RFID (Radio Frequency Identification), has many advantages for farm management. In practice, however, RFID implementations can cause several problems. Reading speed and distance must be optimized for specific applications. Image processing is more effective than RFID for the development of precision farming system in livestock. Therefore, the aim of this paper is to attempt the identification of cattle by using image processing. The majority of the research on the identification of cattle by using image processing has been for the black-and-white patterns of the Holstein. But, native Japanese and Korean cattle do not have a consistent pattern on the body, so that identification by pattern is impossible. This research aims to identify to Japanese black cattle, which does not have a black-white pattern on the body, by using image processing and a neural network algorithm. 12 Japanese black cattle were tested. Values of input parameter were calculated by using the face image values of 12 cows. The face was identified by the associate neural memory algorithm, and the algorithm was verified by the transformed face image, for example, of brightness, distortion, noise and angle. As a result, there was difference due to a transformation ratio of the brightness, distortion, noise, and angle. The algorithm could identify 100% in the range from -30 to +30 degrees of brightness, -20 to +40 degrees of distortion, 0 to 60% of noise and -20 to +30 degree of angle transformed images.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.2
• /
• pp.214-219
• /
• 2011

This paper presents a multi-band low noise amplifier(LNA) with switching operation for 2.4, 3.5 and 5.2 GHz bands using CMOS 0.18 um technology. The proposed circuit uses switching transistors to achieve the input and output matching for multi-band. By using the switching transistors, we can adjust the transconductance, gate inductance and gatesource capacitance at input stage and total output capacitance at output stage. The proposed LNA exhibits gain of 14.2, 12 and 11 dB and noise figure(NF) of 3, 2.9 and 2.8 dB for 2.4, 3.5 and 5.2 GHz, respectively.

• International Journal of Computer Science & Network Security
• /
• v.24 no.4
• /
• pp.206-210
• /
• 2024

Industrial facilities that use modern IT technologies require the ensured reliability and security of information in automated enterprise management. Concurrently, so as to ensure a high quality of communication, it is necessary to expand the bandwidth of communication channels, which are limited by the physical parameters of the radio frequency spectrum. In order to overcome this contradiction, we propose the application of technology fundamental to ultra-wideband signals, in which the ratio between the bandwidth and its central part is greater than "one". For this reason, the information signal is emitted without a carrier frequency - simultaneously within the entire frequency band - provided that the signal level is lower than the noise level. For the transmission of information content, the method of positional-time coding is used, in which each information bit is encoded by hundreds of ultrashort pulses that arrive within a certain sequence. Mathematical models of signals and values observed in wireless communication systems with autocorrelation reception of modulated ultra-wideband signals are furthermore recommended. These assist in identifying features of the dependence of the error probability on the normalized signal-to-noise ratio and the signal base. Comparative analysis has shown that the best noise immunity of the systems considered in this paper is the communication system, which uses the time separation of the reference and information signals. During the first half of the bit interval, the switch closes the output of the transmitter directly to the generator of the ultra-wideband signal - forming a reference signal. In the middle of the bit interval, the switch alternates the output to one of two possible positions depending on the encoding signal - "zero" or "one", forming the information part of the ultra-wideband signal. It should also be noted that systems with autocorrelation reception and separate transmission of reference and information signals, provide a high level of structural signal secrecy. Furthermore, they provide the reliable transmission of digital information, especially in interference conditions.