• Current Photovoltaic Research
• /
• v.12 no.2
• /
• pp.31-36
• /
• 2024

Passivating contacts are a promising technology for achieving high efficiency Si solar cells by reducing direct metal/Si contact. Among them, a polysilicon (poly-Si) based passivating contact solar cells achieve high passivation quality through a tunnel oxide (SiO_x) and poly-Si. In poly-Si/SiO_x based solar cells, the passivation quality depends on the amount of dopant in-diffused into the bulk-Si. Therefore, our study fabricated cells by inserting silicon oxide (SiO₂) as a doping barrier before doping and analyzed the barrier effect of SiO₂. In the experiments, p⁺ poly-Si was formed using spin on dopant (SOD) method, and samples ware fabricated by controlling formation conditions such as existence of doping barrier and poly-Si thickness. Completed samples were measured using quasi steady state photoconductance (QSSPC). Based on these results, it was confirmed that possibility of achieving high V_oc by inserting a doping barrier even with thin poly-Si. In conclusion, an improvement in implied V_oc of up to approximately 20 mV was achieved compared to results with thicker poly-Si results.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.406-406
• /
• 2016

To get high efficiency n-type crystalline silicon solar cells, passivation is one of the key factor. Tunnel oxide (SiO2) reduce surface recombination as a passivation layer and it does not constrict the majority carrier flow. In this work, the passivation quality enhanced by different chemical solution such as HNO3, H2SO4:H2O2 and DI-water to make thin tunnel oxide layer on n-type crystalline silicon wafer and changes of characteristics by subsequent annealing process and firing process after phosphorus doped amorphous silicon (a-Si:H) deposition. The tunneling of carrier through oxide layer is checked through I-V measurement when the voltage is from -1 V to 1 V and interface state density also be calculated about $1{\times}1012cm-2eV-1$ using MIS (Metal-Insulator-Semiconductor) structure . Tunnel oxide produced by 68 wt% HNO3 for 5 min on $100^{\circ}C$, H2SO4:H2O2 for 5 min on $100^{\circ}C$ and DI-water for 60 min on $95^{\circ}C$. The oxide layer is measured thickness about 1.4~2.2 nm by spectral ellipsometry (SE) and properties as passivation layer by QSSPC (Quasi-Steady-state Photo Conductance). Tunnel oxide layer is capped with phosphorus doped amorphous silicon on both sides and additional annealing process improve lifetime from $3.25{\mu}s$ to $397{\mu}s$ and implied Voc from 544 mV to 690 mV after P-doped a-Si deposition, respectively. It will be expected that amorphous silicon is changed to poly silicon phase. Furthermore, lifetime and implied Voc were recovered by forming gas annealing (FGA) after firing process from $192{\mu}s$ to $786{\mu}s$. It is shown that the tunnel oxide layer is thermally stable.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.82.1-82.1
• /
• 2010

수소화된 비정질 실리콘 박막을 이용한 반도체는 현재 태양전지, 트랜지스터, 매트릭스 배열 및 이미지 센서 등의 분야에서 이용되고 있다. 자세히 이야기 하면, 여러 가지의 광전효과 물질에 대한 특성이 있으며, 가시광선영역에 대하여 > $10^5cm^{-1}$이상의 매우 높은 광흡수계수와 낮은 온도를 갖는 증착공정 등이 있다. 박막의 밴드갭은 약 1.6~1.8eV로서 태양전지의 흡수층과 passivation층으로 적절하다. 여러 가지 종류의 태양전지 중 비정질 실리콘 박막/결정질 실리콘 기판의 구조로 이루어진 이종접합 태양전지는 저온에서 공정이 가능한 대표적인 것으로서 HIT(Heterojunction with Intrinsic Thin layer)구조로 산요사에 의해 제안된 것이다. 이것은 결정질 실리콘 기판과 도핑된 비정질 실리콘 박막사이에 얇은 진성층 비정질실리콘 박막을 삽입함으로서, 캐리어 전송을 좋게하여 실리콘 기판 표면의 passivation효과를 증대시키는 결과를 가지고 온다. 실험실 규모에서는 약 20%이상의 효율을 보이고 있으며, 모듈에서는 19.5%의 높은 효율을 보이고 있어 실리콘 기판을 이용한 고효율 태양전지로서 각광을 받고 있다. 이러한 이종접합 태양전지의 대부분은 단결정 실리콘을 사용하고 있는데, 점차적으로 다결정 실리콘 기판으로 추세가 바뀌고 있어, 여기에 맞는 표면 passivation 공정 및 분석이 필요하다. 본 발표에서는 다결정 실리콘 기판위에 진성층 비정질 실리콘 박막을 유도결합 플라즈마 화학기상 증착법(ICP-CVD)을 이용하여 제조하여 passivation 효과를 분석한다. 일반적으로 ICP는 CCP(coupled charged plasma)에 비해 약 100배 이상 높은 플라즈마 밀도를 가지고 있으며, 이온 충돌같은 표면으로 작용하는 것들이 기존 방식에 비해서 작다라는 장점이 있다. 먼저, 유리기판을 사용하여 ICP-CVD 챔버내에 이송 한 후 플라즈마 파워, 온도 및 가스비(SiH4/H2)에 따른 진성층 비정질 실리콘 박막을 증착 한 후, 밴드갭, 전도도 및 결합구조 등에 대한 결과를 분석한 후, 최적의 값을 가지고 250um의 두께를 갖는 다결정 실리콘을 기판위에 증착을 한다. 두께(1~20nm)에 따라 표면의 passivation이 되는 정도를 QSSPCD(Quasi steady state Photoconductive Decay)법에 의하여 소수캐리어의 이동거리, 재결합율 및 수명 등에 대한 측정 및 분석을 통하여 다결정 실리콘 기판의 passivation effect를 확인한다. 제시된 데이터를 바탕으로 향후 다결정 HIT셀 제조를 통해 태양전지 효율에 대한 특성을 비교하고자 한다.

• Korean Journal of Soil Science and Fertilizer
• /
• v.36 no.4
• /
• pp.200-209
• /
• 2003

Distribution coefficient ($K_d$) is an universal parameter estimating cadmium partition for a soil-water-crop system in agricultural lands. This study was performed to find some factors affecting soil-water partition coefficients for cadmium in some Korean soils. The distribution coefficients ($K_d$) of cadmium for the 15 series of agricultural soils were measured at quasi-steady state in the pH ranges from 2 to 11. The adsorption data of the selected soils showed a linear relationship between log $K_d$ and pH, which was well agreed with theoretically expected results ; $log\;K_d=0.6339pH+0.5532(r^2=0.70^{**})$. Normalization of the partition coefficients were performed in a range of pH 3.5 ~ 8.5 to minimize adverse effects of Al dissolution, cationic competition, and organic matter dissolution. The $K_d$-om, partition coefficients normalized for organic matter, improved this linearity to the pH of soils. The values of $K_d$-om measured from the field samples were significantly correlated with those of $K_d$ predicted from the sorption-edge experimental data ($r^2=0.68^{**}$).

• Korean Journal of Materials Research
• /
• v.21 no.5
• /
• pp.243-249
• /
• 2011

To reduce manufacturing costs of crystalline silicon solar cells, silicon wafers have become thinner. In relation to this, the properties of the aluminium-back surface field (Al-BSF) are considered an important factor in solar cell performance. Generally, screen-printing and a rapid thermal process (RTP) are utilized together to form the Al-BSF. This study evaluates Al-BSF formation on a (111) textured back surface compared with a (100) flat back surface with variation of ramp up rates from 18 to $89^{\circ}C$/s for the RTP annealing conditions. To make different back surface morphologies, one side texturing using a silicon nitride film and double side texturing were carried out. After aluminium screen-printing, Al-BSF formed according to the RTP annealing conditions. A metal etching process in hydrochloric acid solution was carried out to assess the quality of Al-BSF. Saturation currents were calculated by using quasi-steady-state photoconductance. The surface morphologies observed by scanning electron microscopy and a non-contacting optical profiler. Also, sheet resistances and bulk carrier concentration were measured by a 4-point probe and hall measurement system. From the results, a faster ramp up during Al-BSF formation yielded better quality than a slower ramp up process due to temperature uniformity of silicon and the aluminium surface. Also, in the Al-BSF formation process, the (111) textured back surface is significantly affected by the ramp up rates compared with the (100) flat back surface.

• Journal of Ecology and Environment
• /
• v.31 no.1
• /
• pp.45-67
• /
• 2008

Ocean climate variables ($1900{\sim}2005$), time series of catches ($1910{\sim}2005$) and body size data were used to assess the year-to-year and decadal scale fluctuations in abundance of the fish populations (Japanese sardine, anchovy, jack mackerel, chub mackerel, Pacific saury and common squid) that have spawning grounds in the East China Sea and its adjacent regions. A negative correlation between the abundance of pelagic fishes (e.g. jack mackerel) in the Tsushima Warm Current (TWC) region and the Kuroshio-Oyashio Current (KOC) region was attributed to the climatic modulation of larval transport and recruitment, which depends on the winter monsoon-induced drift, current systems, and spawning season and site. The changes in abundance and alternation of dominant fish populations in the two regions in the 1930s, 1970s, and late 1980s mirrored changes in the climate indices (ALPI, AOI and MOI). Oscillations in the decadal climate shifts between the two regions led to zonal differences in larval transport and recruitment, and hence differences in the abundance of the pelagic fish populations. During deep Aleutian Lows, as in the 1980s, larval transport from the East China Sea to the KOC region increases in association with the strong winter Asian monsoon, cool regime and increased volume transport of the Kuroshio Current systems, whereas during a weak Aleutian Low (as in the 1990s), larval transport to the TWC region increased in association with a weak winter Asian monsoon, a warm regime, and increased volume transport of the Tsushima current system. We postulate that the increased chub mackerel abundance in the TWC region and the decreased abundance in the KOC region in the 1990s are partly attributed to changes in recruitment and availability to the fishing fleets under the warm regime in the spawning and nursery grounds in the East China Sea in association with the quasi-steady state of mild winter monsoon in the 1990s. The fluctuations in chub mackerel and jack mackerel abundance are under the environment-dependant growth form, although the tropicalization was identified in the TWC region. The density-dependant growth form was found in Japanese sardine populations, but no tropicalization by fishing was identified in the long ($10{\sim}15$ year) periods of abundance despite their short ($3{\sim}4$ year) generation time, suggesting that the environment-dependant growth form drove the changes in abundance. Year-to-year and decadal scale variations in abundance and population structure of the Pacific saury responded to climate regime shifts (1976/1977, 1988/1989), suggesting that the fish is a key bio-indicators for changes in the ecosystem.

• Elastomers and Composites
• /
• v.46 no.3
• /
• pp.237-244
• /
• 2011

Five natural rubber (NR) composites with different reinforcing systems of unfilled, carbon black, carbon black with silane coupling agent, silica, and silica with silane coupling agent were thermally aged and change of the crosslink densities by the accelerated thermal aging was investigated. The crosslink densities on the whole increased as the aging time elapsed irrespective of the reinforcing systems. The crosslink density changes became noticeable by increasing the aging temperature. For carbon black-filled composites, the silane coupling agent made the crosslink density change to be increased. For silica-filled composites, however, the silane coupling agent made the crosslink density increment reduced at 60 and $70^{\circ}C$ and it hardly affect the degree of the crosslink density change at 80 and $90^{\circ}C$. The activation energies for the crosslink density changes of the carbon black-filled samples increased continuously in a logarithmic fashion, whereas that of the silica-filled one showed a quasi-steady state ranges at aging times of 30-150 days. The activation energy of the unfilled sample increased exponentially with the aging time. The experimental results were explained with sulfur donation from the silane coupling agent, surface modification of the filler by the silane coupling agent, adsorption of curative residues on the silica surface, and release of the adsorbed curative residues.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.14 no.2
• /
• pp.136-150
• /
• 2002

To improve the water quality of the recently constructed Siwhaho, sluice gates were operated to allow free exchange of water with the sea. This estuarine lake connected to the outer sea through narrow gates is affected mainly by flushing by gate operation and river flows and wind forcing sometimes. As a predicting tool far the water qualities, a three-dimensional finite volume model CE-QUAL-ICM is incorporated into a finite element hydrodynamic model, TIDE3D. In coupling these two different modules, a new error minimization technique is applied by considering conservation of mass. Model tests for one year after calibration and validation using field observation show that eutrophication and other biological changes reach quasi-steady state after initial 60 days of simulation, thus it would be necessary to consider moderate ramp up option to remove initial uncertainties due to cold start option. Sediment-water interaction might not be a concern in the long-term simulation, since its effect is negligible. Simulated results show the newly applied scheme can be applied with satisfaction not only fur lessening of eutrophic processes in an estuarine lake but also looking for some active circulation to improve water quality.