• 분석과학
• /
• 제8권4호
• /
• pp.461-464
• /
• 1995

Three wavelength spectrophotometry was used to determine the content of eugenol in Eugenia Caryophyllata Thunb. Using this method could effectively eliminate the deviation of background absorption caused by the change of concentration and the error of quantitative analysis caused by asymmetric peaks, and at the same time the leaning degree of base line was corrected. This method was simple the recovery ratio was 90.05%-116.94% and the coefficient of variation was 3.5%.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2014년도 추계학술대회 논문집
• /
• pp.176-177
• /
• 2014

The new algorithm was proposed to quantify symmetry recorded in convergent beam electron diffraction (CBED) patterns and symmetry mapping. The proposed algorithm is based on the normalized cross-correlation coefficient (${\gamma}$) for quantifying the amount of symmetry in a CBED pattern. The quantification and mapping procedures are automatically controlled by the script implemented in Gatan Digital Micrograph$^{(c)}$. We apply the quantitative CBED measurement to a strained Si sample to test the sensitivity to defects.

• Journal of Microbiology and Biotechnology
• /
• 제10권6호
• /
• pp.885-888
• /
• 2000

Electroantennogram(EAG) can be applied to detect odorants since insects have highly specialized olfactory receptors inside their antennae. The characteristics of EAG parameters were investigated for the quantitative measurement of a general odorant using ammonia as a model odorant. The antennae of male silkworm moth, Bombyx mori, were used for the EAG. The electical signal curves generated from a pair of antennae originating from the same silkworm moth were never identical; however, they exhibited a typical type I or type II characteristic curve pattern for every pair of antennae. The correlation between the EAG parameters and the ammonia concentration was analyzed for the type I and type II antennae. The stability of each parameter was also investigated for each type of antenna. The results show the possibility of the quantitative measurement of general odorants using the EAG technique.

• 대한치과의사협회지
• /
• 제55권5호
• /
• pp.358-364
• /
• 2017

Nowadays, there has been an increasing interest in the preservation of natural dentition and the proper occlusion related to tooth wear for quality of life. Tooth wear means the loss of tooth enamel structure. This is happened by many causes which is the combined effects of many mechanisms. For keeping proper occlusion, dentists should check tooth wear status with acceptable methods and tools for the proper diagnosis. Until now, there have been many traditional qualitative ways to measure tooth wear which are intuitive, rapid, and simple. On the contrast, they are not objective nor reproducible. With the development of related technique, new quantitative methods using CAD and 3d scanners. This article aimed to introduce qualitative and quantitative methods for tooth wear measurements.

• 패션비즈니스
• /
• 제12권3호
• /
• pp.54-61
• /
• 2008

The glitter of lame fabrics containing the metallic yarns may further be altered by $Na_2CO_3$ aqueous solution at an elevated temperature. In this study, the effect of the corrosion treatment on the yarn luster was evaluated using image analysis. The alkaline solution treatment was found to be more effective on the aluminum-based specimens than on the silver-based specimens. It was found that corrosion percentage measurement based on the transmission analysis may provide reasonable quantitative index, even if the measurement relies on an indirect method. Based on the quantitative results, the alkaline treatment condition for the specific specimen would be optimized for a desired glitter modification.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2021년도 봄 학술논문 발표대회
• /
• pp.255-256
• /
• 2021

The performance measurement of construction projects has traditionally been evaluated as a prerequisite for successful project completion. Considering this importance, the UK and the US are operating quantitative performance measurement systems for construction projects. However, in the case of Korea, there is a limit to the use of existing methods due to the limitation of data collection. Recently, in consideration of the domestic situation, research is being conducted to measure the quantitative performance of a project by using big data including progress and project attribute information. Therefore, this study aims to present the design direction of a performance monitoring system using Quality Function Deployment.

• 대한한의학회지
• /
• 제35권4호
• /
• pp.74-82
• /
• 2014

Objectives: Quantification, objectification, and standardization of lifting-thrusting manipulation are important issues in traditional Chinese medicine (TCM). The purpose of this study was to quantitatively investigate the difference in the amount of stimulation according to range and frequency among parameters of lifting-thrusting manipulation with the use of a needle insertion-measurement system. Methods: For quantification of lifting-thrusting manipulation, an acupuncture needle insertion-measurement system was used in phantom tissue. The motor and force sensors of the needle insertion device were connected to the control software. This enabled operation of the lifting-thrusting manipulation and measurement of the acupuncture needle force. The measurement of the acupuncture needle force according to various frequencies (0.25, 0.50, 0.75, and 1 Hz) and ranges of movement (2, 4, 6, 8, and 10 mm) was repeated 10 times. Results: At a constant frequency of movement, acupuncture needle force according to range of movement (2, 4, 6, 8, and 10 mm) increased with increasing range of movement (p < 0.05). At a constant range of movement, acupuncture needle force according to frequency of movement (0.25, 0.50, 0.75, and 1.0 Hz) increased with increasing frequency of movement (p < 0.05). Conclusion: In this study, we conducted a quantitative comparison of the amount of stimulation according to range and frequency, the main parameters of lifting-thrusting manipulation, by using an acupuncture needle insertion-measurement system. Future studies on various manipulations and parameters are warranted to quantify and objectify the amounts of stimulation by acupuncture manipulation.

• 한국소음진동공학회논문집
• /
• 제16권1호
• /
• pp.40-49
• /
• 2006

A novel disturbance measurement method, model based disturbance observer (MBDO) for optical disk drives (ODDs), is proposed and the disturbance analysis using the proposed method is performed under various conditions. In ODDs, the quantitative and qualitative analysis for the generated disturbance during normal operation is very important to successful servo loop design. However, the disturbance measurement is difficult, and high precision measurement is necessary. Furthermore, the conventional disturbance measurement method using a LDV (laser Doppler vibrometer) has many difficulties in eccentricity direction due to the vertical movement of an optical disk. To solve this problem, the MBDO is proposed. First, the relationship between the servo loop for ODDs and the generated disturbance are briefly reviewed. Second, the principle of the MBDO is introduced, and the disturbance measurement results, which are measured by the MBDO and a LDV, are compared. In these experiments, test DVD-ROM disks are used to generate quantitative/qualitative disturbance. Then, the disturbance analysis under various conditions is performed using waterfall technique. This technique clearly shows the disturbance trend from the inner part of an optical disk to the outer part of it. Finally, the various disturbances measurement results are summarized and some remarks for it are commented.

• Applied Microscopy
• /
• 제45권2호
• /
• pp.101-105
• /
• 2015

Numerous digital image analysis techniques have been developed with regard to transmission electron microscopy (TEM) with the help of programming. DigitalMicrograph (DM, Gatan Inc., USA), which is installed on most TEMs as operational software, includes a script language to develop customized software for image analysis. Based on the DM script language, this work provides a script source listing for quantitative strain measurements based on a geometric phase analysis.

• 한국어업기술학회:학술대회논문집
• /
• 한국어업기술학회 2000년도 춘계수산관련학회 공동학술대회발표요지집
• /
• pp.383-384
• /
• 2000

Most of the photoperiodic responses result in a sharp contrast between development in long and short days, so that qualitative observations are quite sufficient to establish that development is under photoperiodic control, and qualitative information of this type is all that is available for many of the responses (Dring 1984). However, we need to devise some quantitative measurement of the response in order to study the physiological mechanism of photoperiodic control. We report here the quantification of photoperiodic control of erect thalli production of Sargassum muticum in different daylength regimes. (omitted)