• Proceedings of the KIEE Conference
• /
• 2006.10d
• /
• pp.197-199
• /
• 2006

This paper proposes the method to improve the charging speed of high voltage capacitor used in the medical device with high voltage. Feedback control method with microprocessor was used to detect and control the charging voltage. The result shows that the proposed method is more efficient than the previous converting method with typical PWM IC.

• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.53 no.9
• /
• pp.615-621
• /
• 2004

This paper describes the design of a 2-phase stepping motor driver using CPLD. The driver IC such as L297, which is mostly used has some difficulties in PWM current control because of the switching noise of power MOSFETs. The switching noise causes current ripple and acoustic noise. To reduce the switching noise, we designed a digital filter using VHDL. Also we designed constant current method for 1-2 phase(half step) excitation to reduce the torque ripple. Experimental results show the effectiveness of the proposed method. It is enabling further enhancements of stepping motor drive technology broadening the range of applications for the stepping motors.

• Proceedings of the KIEE Conference
• /
• 2003.11c
• /
• pp.910-915
• /
• 2003

This paper describes the design of a 2-phase stepping motor driver using CPLD(Complex Programmable Logic Device). The driver IC such as L297 (SGS-Thomson Microelectronics), which is mostly used has some problems in PWM control because of the switching noise of power MOSFETs. It causes current ripple and acoustic noise. To improve theses characteristics, we proposed a new current control method that the output PWM frequency is almost constant using a digital filter. Also we proposed constant current method for 1-2 phase(half step) excitation. The proposed method is implemented with CPLD(Xilinx, XC9572-PC44). Experimental results show the effectiveness of the proposed method.

• Proceedings of the KIEE Conference
• /
• 1992.07b
• /
• pp.1176-1178
• /
• 1992

This paper shows enhanced working performance of the battery fork-lift truck by developing the IGBT full bridge dc-dc convertor using one-chip micro-processor. The PWM pulse is generated from a 16 bit one-chip micro-processor for the speed control of DC motor. In order to ensure the operation of IGBT and motor pecewisely, IGBT gate drive circuit was designed by using current limiting IC and hige voltage limit IC. And also It is able to regenerative braking.

• Journal of the Korean Society of Industry Convergence
• /
• v.22 no.3
• /
• pp.373-379
• /
• 2019

Nowadays, the IoT portable electronic devices have become more useful and diverse, so they require various supply voltage levels to operate. This paper presents a DC-DC buck converter with pulse width modulation (PWM) for portable electronic devices. The proposed step-down DC-DC converter consists of passive elements such as capacitors, inductors, and resistors and an integrated chip (IC) for signal control to reduce power consumption and improves ripple voltage with the resolution. The proposed DC-DC converter is simulated and analyzed in PSPICE circuit design platform, and implemented on the prototype PCB board with a Texas Instruments LM5165 IC. The proposed buck converter is showed 92.6% of peak efficiency including a load current range of 4-10 mA, 3.29 mV of the voltage ripple at 5 V output voltage for the supply voltage 12 V. Measured and Simulated power efficiency are made good agreement with each other.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.24 no.1
• /
• pp.152-159
• /
• 2010

High power density and power conversion efficiency have been required in the power converters according to the rapid growth of industry. In this context, the next generation High Speed Train(HST) requires power converter which has high-efficiency, high-performance and high-density. In this paper, the new control technique for battery charger used for the next generation HST is proposed. The phase shift ZVZCS converter is classified according to a resonant circuit which is located in the primary or secondary side. In this paper, The PWM switching technique using all-pass filter is proposed to control ZVZCS converter which has resonant circuit in the secondary side. ATmega_128 micro controller based in all-pass filter in substitute for phase shift IC is presented to have digital control. To verify the proposed topology, the simulation and experiment are performed by using PSIM software and 1[kW] experimental set-up.

• Journal of IKEEE
• /
• v.13 no.2
• /
• pp.208-215
• /
• 2009

The high efficiency power management IC(PMIC) with DT-CMOS(Dynamic Threshold voltage MOSFET) switching device for portable application is proposed in this paper. Because portable applications need high output voltages and low output voltage, Boost converter and Buck converter are embedded in One-chip. PMIC is controlled with PWM control method in order to have high power efficiency at high current level. DTMOS with low on-resistance is designed to decrease conduction loss. Boost converter and Buck converter, are based on Voltage-mode PWM control circuits and low on-resistance switching device, achieved the high efficiency near 92.1% and 95%, respectively, at 100mA output current. And Step-down DC-DC converter in stand-by mode below 1mA is designed with LDO in order to achive high efficiency.

• The Journal of the Korea Contents Association
• /
• v.7 no.1
• /
• pp.116-123
• /
• 2007

This paper proposed a new amplitude width modulation for OLED data driver IC. The data driver controls brightness of OLED by adjusting amplitude and width of the data drive current pulse. There were two conventional methods; pulse amplitude modulation(PAM) and pulse width modulation(PWM). The PWM method suffered from lower light emitting time efficiency at low luminance signal. The PAM method suffered from large chip area using DACs for each column. The proposed method was aiming at accurately controlling of the current level by MSB data and light emitting efficiency by LSB data to improve the inefficiencies of the PAM and a PWM. The proposed AWM driver circuit implemented using $0.35-{\mu}m$ 3-poly 4-metal CMOS high voltage process. The simulation result shows the improvement in the accuracy of the gray level control even though the driver circuit is smaller than the PAM.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.14 no.6
• /
• pp.504-513
• /
• 2009

This paper proposes the new type LED driver modularization for illumination LED driver. The proposed LED driver circuit insulates a hot GND of AC input power and a cold GND of LED driver part by using a fly-back converter. In order to control easily the current of the LED, the fly-back converter is operated in the discontinuous mode with excellent dynamic characteristics, and the characteristics of the LED are verified after the closed loop control is performed using a KIA2431. The LED driver module allows the wide AC power input ranges and realizes the burst dimming function which directly regulates a PWM control IC. This paper describes the operation principle of the LED driver module and it is proved the usefulness through the real model with experimentation. Besides, this paper proposes the multi-channel LED driver which the miniaturized and modularized LED driver module are connected by parallel, and verified its propriety by experiments.

• Proceedings of the KIPE Conference
• /
• 2008.06a
• /
• pp.367-369
• /
• 2008

본 논문은 중용량에 적합한 새로운 이중출력 LLC 공진형 DC/DC 컨버터에 관한 것으로써, 별도의 Post-regulator및 추가되는 제어 IC 없이 정밀한 이중출력이 가능한 새로운 방식의 컨버터를 제안한다. 제안된 컨버터의 제어방식은 펄스폭 변조(PWM)와 동시에 주파수 변조(PFM)를 통해 이루어지며 Master 와 Slave 출력을 각각 주파수, 듀티로 제어함으로써 Slave 출력을 위한 별도의 Post-Regulator 및 제어 IC가 필요 없기 때문에, 저가의 컨버터 구현이 가능하다. 또한 기존 LLC 공진형 DC/DC 컨버터와 같이 스위칭 소자의 영전압 스위칭이 보장되는 동시에, Post-Regulator 로 인한 손실이 없기 때문에 효율 및 발열 특성이 매우 우수하다. 본 논문에서는 제안된 컨버터의 우수성과 신뢰성 검증을 위해, 실제로 50" FHD급 PDP용 전원회로를 위한 시작품을 제작하고 이를 이용한 실험결과를 바탕으로 제안된 컨버터의 타당성을 검증한다.