• 한국해양공학회지
• /
• 제12권2호통권28호
• /
• pp.1-21
• /
• 1998

In this paper, a non-conforming 3-D 8-node solid element(MQM10) has beets applied to the analyses of static and dynamic bending problems of laminated composite plates The QM10 element exhibits stiffer bending stiffness which is caused by the reduction of degree of freedom from Q11 element. As an effective way to correct the relative stiffness stiffening phenomenon the modification of Gauss sampling points for composite plates is proposed. The quantity of modification is a function of material properties. Also, another two modified equations are obtained, one is modification for stress, and the other is modification of coefficient of shear modulus in free vibration. It is noted that MQM10 element can analyse the static and free vibration problems of various 3-dimensional composite plates composed of unidirectional laminae, woven laminae or braided laminae. The results of MQM10 element are in good agreement with those of 20-node element.

• Structural Engineering and Mechanics
• /
• 제52권4호
• /
• pp.723-738
• /
• 2014

Prestressing is the most commonly employed technique in bridges and long span beams in commercial buildings as prestressing results in slender section with higher load carrying capacities. This work is an attempt to study the performance of a minimum weight prestressed concrete beam adopting a non-prismatic section so that there will be a reduction in the volume of concrete which in turn reduces the self-weight of the structure. The effect of adopting a non-prismatic section on parameters like prestressing force, area of prestressing steel, bending stresses, shear stresses and percentage loss of prestress are established theoretically. The analysis of non-prismatic prestressed beams is based on the assumption of pure bending theory. Equations are derived for dead load bending moment, eccentricity, and depth at any required section. Based on these equations an algorithm is developed which does the stress checks for the given section for every 500 mm interval of the span. Limit state method is used for the design of beam and finite difference method is used for finding out the deflection of a non-prismatic beam. All the parameters of nonprismatic prestressed concrete beams are compared with that of the rectangular prestressed concrete members and observed that minimum weight design and economical design are not same. Minimum weight design results in the increase in required area of prestressing steel.

• 대한조선학회논문집
• /
• 제52권4호
• /
• pp.349-355
• /
• 2015

Through the recent accident, the checking of ultimate hull girder capacity for container ship should be needed. Smith’s method is well known as the only simplified method to access rapidly for ultimate hull girder capacity except very expensive nonlinear F.E approach. This simplified method, however, is admitted to apply only to bulker and tanker in accordance with Classification Rules up to now. The targets of this study are to verify effectiveness of the simplified method for container ship’s ultimate hull girder strength and to propose the safety factor considering the local bending in double bottom structures due to out of plane loads through the nonlinear F.E analyses. Two different sized ships and three loading conditions which are pure bending, homo-loading and one-bay empty condition were used for this study. Based on the F.E results, the present study showed that CSR’s simplified method is available for the ultimate hull girder strength of container ship and over 1.2 of safety factor should be applied to consider the local bending effect in double bottom structures due to out of plane loads such as sea pressure an cargo.

• 대한기계학회논문집A
• /
• 제25권11호
• /
• pp.1829-1834
• /
• 2001

The aim of this study is to investigate the ductile fracture behavior under mixed mode (I/II) loading using SA533B pressure vessel steel. Anti-symmetric 4-point (AS4P) bonding tests were performed to obtain the J-R curves under two different mixed mode (I/II) loadings. In addition, the fractographic examination of fracture surfaces was carried out to compare with those of pure Mode I and Mode II. In conclusions, the J-R curves under Mixed Mode (I/II) loading were located between those of Mode I and Mode II loadings. When the mixture ratio of mixed mode (I/II) loading was high, the J-R currie of mixed mode (I/II) loading approached that of pure mode I loading after some amount of crack propagation. In contrast with the above fact, if the mixture ratio was low, the J-R curve looked after that of pure mode II loading. The fractographic evidences such as the shape of dimples under different loading conditions supported these conclusions.

• 한국강구조학회 논문집
• /
• 제16권1호통권68호
• /
• pp.91-101
• /
• 2004

본 연구는 철골조 초고층 아파트에 있어서 주거부분의 충고를 낮추기 위한 새로운 보-슬래브 구조시스템 개발을 위하여 제안되어진 합성보에 대해서 역학적 성능 및 구조적인 검토를 실험적으로 고찰하여 그 타당성을 확인하고 구조설계의 지침을 제시하고자 하는 것이다. 이상과 같은 연구목적을 달성하기 위해서 제안된 아파트의 기준층 구조평면에 근거하여 본 연구의 대상이 되는 9.8m 스팬의 보를 대상으로 구조재료실험, 합성보의 균등 흼실험, 합성보의 중앙집중 재하실험, 휨 전단 가력실험, 그리고 전단 가력실험 등을 진행하였다. 실험결과로부터 상플랜지에 스터드 커넥터를 대한건축학회 강구조계산규준의 합성보 설계 규정에 따라 정상적으로 배치하고 슬래브의 상부 철근을 정상배근하면 충분한 구조적 성능을 발휘할 수 있음을 확인하였다.

• 산업기술연구
• /
• 제18권
• /
• pp.217-223
• /
• 1998

The springback characteristics of some sheet metals such as commercially pure aluminium, mild steel and stainless steel in a forming process are investigated experimentally. Three geometrical parameters for evaluating springback in the plane-strain draw-bending, which was a benchmark model of NUMISHEET '93 conference, are defined. The measurement of the springback parameters is carried out accurately and easily by using an image analysis system developed in this study. The effects of the blank holding pressure and tensile strength of the material on the springback are also examined.

• 오토저널
• /
• 제13권3호
• /
• pp.58-67
• /
• 1991

A theory of continuum damage mechanics based on the theory of materials of type N was developed and its nonlinear finite element approximation and numerical simulation was carried out. To solve the finite elastoplasticity problems, reasonable kinematics of large deformed solids was introduced and constitutive relations based on the theory of materials of type-N were derived. These highly nonlinear equations were reduced to the incremental weak formulation and approximated by the theory of nonlinear finite element method. Two types of problems, compression moulding problem and pure bending problem, were solved for aluminum 2024.

• 한국표면공학회지
• /
• 제27권1호
• /
• pp.19-28
• /
• 1994

A study on adhesion property of evaporated Al-Cr films was conducted on steel sheet by using two-source evaporator. Adhesion of Al-Cr coated steel was evaluated by tape test after $180^{\circ}$bending. Adhesion was decreased with increasing the Cr content in Al-Cr films. It was thought that the decrease in adhesion with increasing Cr content be related to insufficient wetting and diffusion of Cr atoms in the film. Best adhesion was achieved in the case of pure aluminum film..

• Composites Research
• /
• 제20권3호
• /
• pp.8-16
• /
• 2007

자동차 충돌이나 전복사고에 있어서 부재들의 변형은 축방향 압축붕괴와 함께 굽힘붕괴가 혼합된 변형양상을 보여주고 있으며, 자동차에 사용되는 대부분의 박벽관 부재는 굽힘붕괴가 주된 붕괴형태로 나타나고 있다. 하지만 혼성 사각관의 굽힘붕괴에 대한 연구는 축방향 붕괴의 연구에 비해 많이 부족한 현실이다. 본 논문에서는 알루미늄-복합재료 혼성 사각관의 굽힘 붕괴 거동 및 에너지 흡수 특성을 실험적 방법으로 연구하여 경량화 구조부재로서의 적용가능성을 조사하였다. 접착필름 살입형 경화법으로 제작된 알루미늄-복합재료 혼성 사각관 보에 대해 복합 재료 층의 적층두께와 적층 각에 따른 굽힘 성능을 평가하였다. 본 혼성 사각관 보는 복합재료만으로 구성된 사각관 보에서 발생할 수 있는 불안정한 붕괴모드를 안정적인 붕괴로 전환시키면서, 단순 알루미늄 사각관에 비해 에너지 흡수 능력이 향상되었고, 특히 $[0^{\circ}/90^{\circ}]s$를 적층한 혼성 사각관의 경우 벽두께 1mm인 알루미늄 사각관 시험편과 비교하여 흡수에너지가 1.78배 증가하였고 단위무게당 흡수에너지는 1.29배로 증가함을 보였다.

• 대한기계학회논문집A
• /
• 제38권12호
• /
• pp.1387-1394
• /
• 2014

광탄성 실험법에 의해 측정된 등색프린지 차수를 응력으로 변환시키기 위해서는 광탄성 재료 응력 프린지 상수를 알아야 한다. 광탄성 재료 응력 프린지 상수는 단순 인장시편 또는 압축하중을 받는 원형디스크를 이용하여 측정하는 방법 등이 있다. 이들 방법에서는 시편에 여러 하중을 가하여 하중에 응답하는 프린지 차수의 관계를 최소자승법 등을 이용하여 재료 상수를 결정한다. 본 논문에서는 4점 굽힘 시편에 하중을 가하여 나타나는 프린지로부터 재료 응력 프린지 상수를 결정하였다. 4점 굽힘 시편의 순수 굽힘 구간에서는 주응력 방향이 일정하므로 4단계 위상이동법의 적용이 가능하다. 이 방법은 원형편광기에서 검광판을 0, ${\pi}/4$, ${\pi}/2$, 그리고 $3{\pi}/4$ 라디안 회전시켜 얻은 4개의 광탄성 프린지를 필요로 한다. 4점 굽힘 시편을 이용한 재료의 프린지 상수를 결정하는 방법에서는 일정 하중을 가하여 서로 다른 위치에서도 측정할 수 있는 장점이 있다. 이 방법으로 측정된 재료 응력 프린지 상수는 제조회사에서 제시한 범위이내에 분포하였다.