• 한국산학기술학회논문지
• /
• 제12권10호
• /
• pp.4561-4568
• /
• 2011

본 논문에서는 비엔나 정류기의 전압제어를 위한 반송파 비교 PWM 방법에 대하여 논한다. 일반적으로 산업용 및 통신용 등 여러 응용분야에서 2레벨 정류기가 주로 사용되어 왔다. 하지만 2레벨 정류기는 효율을 높이고, THD를 낮추는데 한계가 있기 때문에 3레벨 정류기에 대한 연구가 진행 되어 왔다. 3레벨 정류기의 대표적인 회로가 비엔나 정류기이다. 기존의 비엔나 정류기는 대부분 전압 명령으로부터 인가 공간전압 벡터를 선택하고, 공간전압 벡터 인가시간을 직접 계산하여, 그 시간동안 전압 명령을 인가하는 공간 전압 변조 방식이 사용된다. 하지만 이 방법은 전압 명령 생성 및 전압 벡터의 인가시간 계산이 매우 복잡하여, 구현이 어려운 단점이 있다. 이 단점을 보완하기 위해 기존의 3레벨 인버터에 사용되던 반송파 비교 PWM 방법을 비엔나 정류기에 적용할 수 있도록 수정하여, 비엔나 정류기를 위한 간단한 전압제어를 위한 반송파 비교 PWM방식을 도출하고 시뮬레이션 및 실험을 통해 검증 한다.

• 전력전자학회논문지
• /
• 제19권6호
• /
• pp.572-581
• /
• 2014

A design and control method of DC/DC converter, which can control variable DC-link voltage to drive a fuel cell electric vehicle (FCEV), is proposed in this study. Given that a fuel cell has low-voltage and high-current characteristics, the required voltage for operating motor must be output through the DC/DC boost converter in the system to drive an FCEV. The proposed converter can choose the output voltage of battery or fuel cell in consideration of the driving mode, as well as control DC-link voltage in accordance with the back electromotive force. The switching lag-time to prevent shortage of pulse-width modulation inverter arms makes distorted current waveform caused by voltage distortion. Through this control method, the proposed converter can reduce the output voltage distortion and current ripple of the inverter, thereby reducing the distorted torque. Simulations and experimental results are presented to verify the reliability of the proposed DC/DC converter.

• 대한전자공학회논문지SD
• /
• 제45권3호
• /
• pp.44-53
• /
• 2008

본 논문에서는 휴대용 오디고 제품의 헤드폰 구동을 위한 델타-시그마 변조기법 기반의 D급 증폭기를 제안한다. 제안된 D급 증폭기는 고성능 단일 비트 4차 델타-시그마 변조기를 이용하여 펄스폭 변조 신호를 발생시킨다. 높은 신호 대 잡음비를 얻는 것과 동시에 시스템의 안정성 확보를 위하여 시뮬레이션을 통해 변조기 루프필터의 폴과 제로를 최적화하였다. 테스트 칩은 $0.18{\mu}m$ CMOS 공정으로 제작되었다. 칩 면적은 $1.6mm^2$ 이며, 20Hz 부터 20kHz까지의 신호대역을 대상으로 동작한다. 3V 전원전압과 32옴의 로드를 사용하여 측정된 출력은 0.03% 이하의 전고조파 왜율을 갖는다.

• Journal of Power Electronics
• /
• 제17권4호
• /
• pp.1048-1057
• /
• 2017

An indirect matrix converter (IMC) is a modern power generation system that enables a direct ac/ac conversion without the need for any bulky and limited lifetime electrolytic capacitor. This system also allows four-quadrant operation, generation of sinusoidal output voltage waveforms with variable frequency and amplitude, and control of input power factor. This study proposes a pulse-width modulation-based sliding-mode controller to achieve unity input-power factor operation of the IMC independently of the active power exchanged with the grid, as well as a fast dynamic response. The designed equivalent control law determines, at each sampling period, the appropriate q-axis component of the modulated input current to be injected into the grid through the LC input filter. An integral term of the error is included in the expression of the sliding surface to increase the accuracy of the control method. A double space vector modulation method is used to synthesize the direction of the space vector of the input currents as required by the sliding-mode controller and the space vectors of the target output voltages. Simulation and experimental results are provided to show the effectiveness and evaluate the performance of the proposed control method.

• 대한임상전기생리학회지
• /
• 제3권1호
• /
• pp.49-59
• /
• 2005

This study assigns each 8 of 24 normal persons to control group(Group I), strength increase group(Group II) and endurance increase group(Group III) to analyze differences in changes of strength and endurance with surface electromyography and kinetics according to application modes of neuromuscular electrical stimulation(NMES). Group I had not any treatment, group II performed 15 repeated contraction with 60% intensity of maximal voluntary isometric contraction(MVIC) by setting 10-sec on time and 50-sec off time and group III conducted 30 repeated contraction with 30% intensity of MVIC by setting 10-sec on time and 20-sec off time. For neuromuscular electrical stimulation, 2,500 Hz of Russian current, 35 pps of pulse rate and 200 of pulse width. Neuromuscular electrical stimulation was conducted by five times for total 4 weeks. Before and after experimentmotor unit action potential of vastus medialis, rectus femoris and vastus lateralis were measured with sEMG, median frequency(MDF) was analyzed, and thus the following results were obtained. There was significant difference in the period of measuring vastus medialis and rectus femoris in change of MDF and interaction among groups with analysis of surface electromyography before and after neuromuscular electrical stimulation(p<.001) and in particular, there was a remarkable change among groups according to the period of measurement. In conclusion, NMES influenced changes of strength and endurance according to its application modes and in particular, it was found that strength increment application had a significant influence on strength increment in applying short-time NMES.

• 대한임상전기생리학회지
• /
• 제5권1호
• /
• pp.33-43
• /
• 2007

This study divided 35 hemiplegia patients into control group having standard physical therapy and gait training and functional electrical stimulation(FES) group using FES during gait training in order to examine the effects of applying FES to ankle joint dorsiflexor on motor unit action potential. Stimulation conditions of FES were pulse rate 35 pps, pulse width $250{\mu}s$, and on-time 0.3 second, treatment hour was 30 min. and treatment period was once a day for five days a week through six weeks. For functional evaluations before and after treatment, root mean square(RMS) were measured and the following conclusions were obtained. : In RMS analysis of motor unit action potential, gastrocnemius was significantly reduced in both weight bearing(p<.001) and bearing condition (p<.05). In conclusion, application of FES to hemiplegia patients in recovery stage during gait training decreased RMS and it was interpreted that it was caused by mitigation of muscular spasticity by reduction of motor unit.

• The Journal of Korean Physical Therapy
• /
• 제19권1호
• /
• pp.11-22
• /
• 2007

Purpose: The purpose of this study were to analysis the effect on change of spinal neuron excitability during gait training of hemiplegia patients by the functional electrical stimulation. Methods: Thirty six hemiplegia patients participated in this study. Stimulation conditions of FES were pulse rate 35pps, pulse width $250{\mu}s$, and on-time 0.3 second, treatment hour was 30 min. and treatment period was once a day for five days a week through six weeks. For functional evaluations before and after treatment, Modified Ashworth Scale (MAS), active range of motion (AROM), Hmax threshold, H/Mmax ratio were measured and the following conclusions were obtained. Results: Functional evaluation showed significant changes in experimental group as MAS(p<0.01), AROM(p<0.001), compared to control group. In spinal neuron excitability evaluation, change of Hmax threshold was significantly reduced in both non weight bearing (p<0.001) and bearing condition (p<0.05), H/Mmax ratio was significantly reduced in non weight bearing (p<0.05) and bearing condition (p<0.05). Conclusion: In conclusion, application of FES to hemiplegia patients in recovery stage during gait training improved mitigation of muscular spasticity, balance adjustment and moving ability and it was interpreted that it was caused by mitigation of muscular spasticity by the spinal neuron excitability.

• 한국전기전자재료학회논문지
• /
• 제20권1호
• /
• pp.92-97
• /
• 2007

This paper performed the basic study for developing the Photodynamic Therapy Equipment for medical treatment. We developed the equipment palpating cell proliferation using a high brightness LED. This equipment was fabricated using a micro-controller and a high brightness LED, and designed to enable us to control light irradiation time, intensity, frequency and so on. Especially, to control the light irradiation frequency, FPGA was used, and to control the change of output value, TLC5941 was used. Control stage is divided into 30 levels by program. Consequently, the current value could be controlled by the change of level in Continue Wave(CW) and Pulse Width Modulation(PWM), and the output of a high brightness LED could be controlled stage by stage. And then, each experiment was performed to irradiation group and non-irradiation group for both Rat bone marrow and Rat tissue cells. MTT assay method was chosen to verify the cell increase of two groups and the effect of irradiation on cell proliferation was examined by measuring 590 nm transmittance of ELISA reader. As a result, the cell increase of Rat bone marrow and tissue cells was verified in irradiation group as compared to non-irradiation group. The fact that specific wavelength irradiation has an effect on cell vitality and proliferation is known through this study.

• IEIE Transactions on Smart Processing and Computing
• /
• 제4권5호
• /
• pp.354-365
• /
• 2015

This work presents an Internet of Things (IoT) system for home energy management based on a custom-designed Impulse Radio Ultra-Wideband (IR-UWB) transceiver that targets a generic and multi-standard control system. This control system enables the interoperability of heterogeneous devices: it integrates various sensor nodes based on ZigBee, EnOcean and UWB in the same middleware by utilizing an ad-hoc layer as an interface between the hardware and software. The paper presents as a first the design of the IR-UWB transceiver for a portable sensor node integrated with the middleware layer, and also describes the receiver connected to the control system. The custom-designed low-power transmitter on the sensor node is fabricated with 130 nm CMOS technology. It generates a signal with a 1.1 ns pulse width while consuming $39{\mu}W$ at 1 Mbps. The UWB sensor node with a temperature measurement capability consumes 5.31 mW, which is lower than the power level of state-of-the-art solutions for smart-home applications. The UWB hardware and software layers necessary to interface with the control system are verified in over-the-air measurements in an actual office environment. With the implementation of the presented sensor node and its integration in the energy management system, we demonstrate achievement of the broad flexibility demanded for IoT.

• 조명전기설비학회논문지
• /
• 제24권1호
• /
• pp.28-34
• /
• 2010

발광다이오드(LED)의 휘도를 제어하는 기존 방식은 펄스폭변조(PWM)방식이 주로 사용되었다. PWM 방식은 LED의 점등시간비와 휘도가 비례하는 아날로그적인 방식으로 통신 등의 디지털 방식과는 호환이 어려운 단점을 가지고 있다. 본 연구에서는 디지털 방식으로 적, 녹, 청색 LED의 휘도를 제어하는 실험을하였다. 이를 위해 LED 구동회로와 디지털 논리회로로 구성된 LED 디지털제어 장치를 개발하였다. 디지털 입력에 대한 적, 녹, 청색 LED의 점등 펄스 수를 제어하여 다양한 광색을 구현하고, 측정한 광색의 x, y 색도좌표가 원하는 색의 CIE 색도도 영역에 포함될 수 있도록 디지털 코드를 최적화시켰다. 본 연구 결과는 디지털 통신을 이용한 LED 램프의 원격 제어로 풀 컬러를 구현하는데 효과적으로 활용될 수 있다.