• 전기학회논문지
• /
• 제62권2호
• /
• pp.232-238
• /
• 2013

In this paper we describe the maximum energy transfer of CSA(Capacitive Switching Antenna). CSA which is radiated antenna system contain energy storage and switch, antenna needs to high voltage source for electrical field radiation experiment. In this experiment we employed Marx generator as a charging source. CSA can radiate electrical field more efficiently by varying antenna capacitance. The electromagnetic generation system which was using CSA has some advantages which are more simple and more effective compared to exist system. We evaluated the performance of electromagnetic wave generating system using CSA. As a result UWB gain of system is 0.47, It is higher level than exist system is 0.3. Radiated electrical field strength at 1m is 70kV/m. It is measured by D-dot sensor and gap distance is 20mm. Center frequency of CSA is approximately 25MHz. When vary the antenna gap distance from 50mm to 20mm, we can find the radiation field strength is decrease and antenna center frequency is increased. We also simulated the energy transfer efficiency to compare with experiment result. Consequentially, CSA needs to appropriate capacitance which is similar value from marx generator for maximum energy transfer, and gap is less than 1mm to increase the CSA capacitance.

• 한국정밀공학회지
• /
• 제17권8호
• /
• pp.157-164
• /
• 2000

This paper presents a method to detect a rotor position and to drive a BLDC motor from standstill to medium speed without any position sensor comparing the current responses due to the inductance variation in the rotor position. A rotor position at a standstill is identified by the current responses of six pulses injected to each phase of a motor. Once the motor stars up pulse train that is composed of long and short pulses is injected to the phase corresponding to produce the maximum torque and the next phase continuously. it provides not only the torque but also the information of the next commutation time effectively when the response of long and short pulses crosses each other after the same time delay. This method which is verified experimentally using a DSP can drive a BLDC motor to the medium speed smoothly without any rattling and time delay compared with the conventional sensorless algorithm.

• 한국화재소방학회논문지
• /
• 제24권1호
• /
• pp.111-115
• /
• 2010

본 논문은 단독형 화재감지기에 무선통신기능을 융합한 화재감지장치를 개발하고자 ZigBee 통신기술을 단독형화재감지기의 신호처리방식으로 채택하여 무선 네트워크와 결합이 가능하도록 설계하였다. 화재감지시 출력전압은 0.4V, 동작 펄스폭은 $600{\mu}s$로 실험하였다. LED감시등은 30초 주기로 동작하고 0.12mA, 동작시에는 0.5초 주기로 하며 사용전류가 7mA가 흐르도록 하여 전원회로, Chamber테스트, 연기테스트, IRED, LED 점등등 각 부분이 일정 시간 내에 정상적으로 동작되어 그 적정성을 확인하였다.

• KEPCO Journal on Electric Power and Energy
• /
• 제6권4호
• /
• pp.405-411
• /
• 2020

In this paper, we designed the COS MEMS system for sensing the falling detection and explosive noise of fuse link in COS (Cut Out Switch) installing on the power distribution. This system analyzed the failure characteristics and an instantaneous breakdown of power distribution. Therefore, our system strengths the industrial competence and guaranties the stable power supply. In this paper, we applied BLE (Bluetooth Low Energy) technology which is suitable protocol for low data rate, low power consumption and low-cost sensor applications. We experimented with LSM6DSOX which is system-in-module featuring 3 axis digital accelerometer and gyroscope boosting in high-performance mode and enabling always-on low-power features for an optimal motion for the COS fuse holder. Also, we used the MP34DT05-A for gathering an ultra-compact, low power, omnidirectional, digital MEMS microphone built with a capacitive sensing element and an IC interface. The proposed COS MEMS system is developed based on nRF52 SoC (System on Chip), and contained a 3-axis digital accelerometer, a digital microphone, and a SD card. In this paper of experiment steps, we analyzed the performance of COS MEMS system with gathering the accelerometer raw data and the PDM (Pulse Data Modulation) data of MEMS microphone for broadcasting the failure of COS status.

• 한국정보통신학회:학술대회논문집
• /
• 한국정보통신학회 2022년도 춘계학술대회
• /
• pp.660-662
• /
• 2022

COVID-19 장기화의 여파로 인해 스트레스 및 정신적 질환을 겪는 현대인이 늘어나고 있다. 최근에는 LED 조명을 이용하여 집중력 향상, 스트레스 완화, 피부관리, 수면의 질 개선 등을 위해 다양한 방법으로 컬러테라피가 연구 되고 있다. 본 논문에서는 사람의 심신 상태를 분석하기 위해 PPG(Photoplethysmogram) 센서를 이용하여 맥파를 계측하고 심박변이도를 추출한다. RGBLED와 아두이노를 이용하여 심리상태 안정에 주로 사용되는 여러 파장의 색상조명을 제작하고, 심신상태의 변화에 따라 자동으로 색상을 변경해주는 무드등 시스템을 제안한다.

• 한국정보처리학회:학술대회논문집
• /
• 한국정보처리학회 2011년도 추계학술발표대회
• /
• pp.1174-1176
• /
• 2011

Unfortunately, the number of blind people increases every 5 seconds in our world. An extensive research was made on improving the conventional walking cane and developing a microcontroller based walking stick for the blind with sensors and a feedback in form of vibration. Two different kinds of sensors are used to detect obstacles, ultrasonic and infrared distance sensors. The signal from an ultrasonic sensor is fed to a microcontroller. With the help of the supporting software, the Pulse Width Modulation (PWM) principle is extensively used to form three zones and run the corresponding vibration motor at different spends according to how far the detected object is located. The other infrared distance sensors are connected to amplifiers and after that to their corresponding vibration motors through motor drivers. The vibration motors are to be located around the user's arm to notify the blind of the obstacles in the intended walking way. It can be very reliable and sufficient device guiding the blind other than the conventional walking cane which has many drawbacks which will be explained and discussed.

• Steel and Composite Structures
• /
• 제48권2호
• /
• pp.131-143
• /
• 2023

The CFRP bar was used to achieve more ductile and durable headed-stud shear connectors in composite components. Three series of push-out tests were firstly conducted, including specimens reinforced with pure steel fibers, steel and CFRP bars. The distributed stress was measured by the commercial PPP-BOTDA (Pre-Pump-Pulse Brillouin optical time domain analysis) optical fiber sensor with high spatial resolution. A series of numerical analyses using non-linear FE models were also made to study the shear force transfer mechanism and crack response based on the test results. Test results show that the CFRP bar increases the shear strength and stiffness of the large diameter headed-stud shear connection, and it has equivalent reinforcing effects on the stud shear capacity as the commonly used steel bar. The embedded CFRP bar can also largely improve the shear force transfer mechanism and decrease the tensile stress in the transverse direction. The parametric study shows that low content steel fibers could delay the crack initiation of slab around the large diameter stud, and the CFRP bar with normal elastic modulus and the standard reinforcement ratio has good resistance to splitting crack growth in headed stud shear connectors.

• 한국음향학회지
• /
• 제28권8호
• /
• pp.806-814
• /
• 2009

이 논문은 능동흡음재를 이용한 수중음향반사파 상쇄에 관한 연구이다. 능동흡음재는 평판형 구동센서와 수신센서로 몰딩되고 외부 제어기와 연결된 구조로 되어있다. 이 두 층의 센서와 피드백제어기는 하나의 피드백 루프를 이루며, 이 루프의 특징은 외부로부터 인가되는 입사파에 대해 음향 임피던스가 자동적으로 정합되어, 자동적으로 반사파를 상쇄하는 특성을 가진다. 능동흡음재의 전기 구조 음향의 다중물리특성은 1차원 전달함수로 모델링 되고, 운용주파수 대역에서 입사파에 대한 반사파가 최소화 되도록 제어기의 전달함수가 설정된다. 능동형 흡음재는 수동형 흡음재의 두께에 비하여 현저히 얇은 두께를 가지며, 간단한 아날로그 회로 제어기만으로도 넓은 주파수 대역에서 우수한 흡음특성을 보인다.

• 생물환경조절학회지
• /
• 제22권4호
• /
• pp.341-348
• /
• 2013

본 연구에서는 토성에 따른 물의 이용효율을 높이면서 재배 작물의 생산성을 최대화하기 위한 효율적인 자동관개 로직을 개발하고자, 수분장력값을 관수 개시점으로 하여 물 공급 유지와 멈춤을 간헐적으로 수행하는 펄스형 관개방식과 측정한 수분장력값을 이용하여 토양수분량을 예측해 재배작물에 적합한 물량을 추가 투입하는 필요물량계산 관수방식을 적용하여 토성이 다른 실험베드에서 2년간 토마토 작물을 재배하면서 토양수분 함량과 장력의 변화를 측정비교하였다. 물공급 30초와 멈춤 30분 및 15분 조건을 이용한 펄스형 관수방식과 필요물량계산 방식에서 얻어진 수분장력값은 목표한 -20kPa 조건에 비해 각각 -42~-8kPa, -20~-10kPa로 나타나 필요물량 계산방식이 균일한 수분장력을 유지하는 측면에서는 유리하였으나 토양수분상태는 상대적으로 습하였다. 공시 토성 모두에서 수분함량은 수분장력에 비해 시간반응이 빠르면서 물공급에 따라 비례적으로 증가하는 경향이 뚜렷하였다. 수분변화 값은 펄스형 관수와 필요물량계산 관수방식의 경우 사양토 기준으로 각각 17~24%, 19~31%로서 펄스형 관수방식이 수분변화 값이 작으면서 시간에 따라 안정적인 값을 유지한 것으로 나타났는데 이는 물공급에 따른 수분함량의 시간변화가 수분장력에 비해 뚜렷하게 빠름과 관계가 있는 것으로 판단하였다. 이러한 결과로부터 펄스형 관수방식은 수분함량값을 이용하여 수분을 조절하는 것이 유리함을 의미한다.

• Journal of Biosystems Engineering
• /
• 제41권3호
• /
• pp.263-272
• /
• 2016

Purpose: Pulse crop damage due to wild birds is a serious problem, to the extent that the rate of damage during the period of time between seeding and the stage of cotyledon reaches 45.4% on average. This study investigated a method of fundamentally blocking birds from eating crops by conducting vinyl mulching after seeding and identifying the growing locations for beans to perform punching. Methods: Infrared (IR) sensors that could measure the temperature without contact were used to recognize the locations of soybean cotyledons below vinyl mulch. To expand the measurable range, 10 IR sensors were arranged in a linear array. A sliding mechanical device was used to reconstruct the two-dimensional spatial variance information of targets. Spatial interpolation was applied to the two-dimensional temperature distribution information measured in real time to improve the resolution of the bean coleoptile locations. The temperature distributions above the vinyl mulch for five species of soybeans over a period of six days from the appearance of the cotyledon stage were analyzed. Results: During the experimental period, cases where bean cotyledons did and did not come into contact with the bottom of the vinyl mulch were both observed, and depended on the degree of growth of the bean cotyledons. Although the locations of bean cotyledons could be estimated through temperature distribution analyses in cases where they came into contact with the bottom of the vinyl mulch, this estimation showed somewhat large errors according to the time that had passed after the cotyledon stage. The detection results were similar for similar types of crops. Thus, this method could be applied to crops with similar growth patterns. According to the results of 360 experiments that were conducted (five species of bean ${\times}$ six days ${\times}$ four speed levels ${\times}$ three repetitions), the location detection performance had an accuracy of 36.9%, and the range of location errors was 0-4.9 cm (RMSE = 3.1 cm). During a period of 3-5 days after the cotyledon stage, the location detection performance had an accuracy of 59% (RMSE = 3.9 cm). Conclusions: In the present study, to fundamentally solve the problem of damage to beans from birds in the early stage after seeding, a working method was proposed in which punching is carried out after seeding, thereby breaking away from the existing method in which seeding is carried out after punching. Methods for the accurate detection of soybean growing locations were studied to allow punching to promote the continuous growth of soybeans that had reached the cotyledon stage. Through experiments using multiple IR sensors and a sliding mechanical device, it was found that the locations of the crop could be partially identified 3-5 days after reaching the cotyledon stage regardless of the kind of pulse crop. It can be concluded that additional studies of robust detection methods considering environmental factors and factors for crop growth are necessary.