• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2009년도 춘계 학술발표회
• /
• pp.419-433
• /
• 2009

Pressure grouting is a common technique in geotechnical engineering to increase the stiffness and strength of the ground mass and to fill boreholes or void space in a tunnel lining and so on. Recently, the pressure grouting has been applied to a soil-nailing system which is widely used to improve slope stability. The soil-nailing design has been empirically performed in most geotechnical applications because the interaction between pressurized grouting paste and the adjacent ground mass is complicated and difficult to analyze. The purpose of this study is to analyze the increase of pullout resistance induced by pressurized grouting with the aid of performing laboratory model tests and field tests. In this paper, two main causes of pullout resistance increases induced by pressurized grouting were verified: the increase of residual stress; and the increase of coefficient of pullout friction. From the laboratory tests, it was found that residual stress in borehole increases by pressurized grouting and dilatancy angle could be estimated by cavity expansion theory using the measured wall displacements. From the field test results, the pullout resistance of soil-nailing with pressurized grouting was found to be 10% larger than that of soil-nailing with gravitational grouting, mainly caused by mean normal stress increase and dilatancy effect. So, the pullout resistance could be estimated by considering these two effects. The radial displacement increases with dilatancy angle increase and the dilatancy angle decreases with injection pressure increase. The measured pullout resistance obtained from field tests is in good agreement with the estimated one from the cavity expansion theory.

• Geomechanics and Engineering
• /
• 제12권4호
• /
• pp.675-688
• /
• 2017

The anchor block is a specially designed concrete member intended to withstand pullout or thrust forces from backfill material of an internally stabilized anchored earth retaining wall by passive resistance of soil in front of the block. This study presents small-scale laboratory experimental works to investigate the pullout capacity of a concrete anchor block embedded in air dry sand and located at different distances from yielding boundary wall. The experimental setup consists of a large tank made of fiberglass sheets and steel framing system. A series of tests was carried out in the tank to investigate the load-displacement behavior of anchor block. Experimental results are then compared with the theoretical approaches suggested by different researchers and codes. The appropriate placement of an anchor block and the passive resistance coefficient, which is multiplied by the passive resistance in front of the anchor block to obtain the pullout capacity of the anchor, were also studied.

• Geomechanics and Engineering
• /
• 제5권4호
• /
• pp.299-312
• /
• 2013

The horizontal pullout capacity of a group of two vertical strip plate anchors, placed along the same vertical plane, in a fully cohesive soil has been computed by using the lower bound finite element limit analysis. The effect of spacing between the plate anchors on the magnitude of total group failure load ($P_{uT}$) has been evaluated. An increase of soil cohesion with depth has also been incorporated in the analysis. For a weightless medium, the total pullout resistance of the group becomes maximum corresponding to a certain optimum spacing between the anchor plates which has been found to vary generally between 0.5B and B; where B is the width of the anchor plate. As compared to a single plate anchor, the increase in the pullout resistance for a group of two anchors becomes greater at a higher embedment ratio. The effect of soil unit weight has also been analyzed. It is noted that the interference effect on the pullout resistance increases further with an increase in the unit weight of soil mass.

• Geomechanics and Engineering
• /
• 제15권3호
• /
• pp.841-849
• /
• 2018

The purpose of a rock bolt is to improve the mechanical performance of a jointed-rock mass. The performance of a rock bolt is generally evaluated by conducting a field pullout test, as the analytical or numerical evaluation of the rock bolt behavior still remains difficult. In this study, wide range of field test was performed to investigate the pullout resistance of rock bolts considering influencing factors such as the rock type, water bearing conditions, rock bolt type and length. The test results showed that the fully grouted rock bolt (FGR) in water-bearing rocks can be inadequate to provide the required pullout resistance, meanwhile the inflated steel tube rock bolt (ISR) satisfied required pullout resistance, even immediately after installation in water-bearing conditions. The ISR was particularly effective when the water inflow into a drill hole is greater than 1.0 l/min. The effect of the rock bolt failure on the tunnel stability was investigated through numerical analysis. The results show that the contribution of the rock bolt to the overall stability of the tunnel was not significant. However, it is found that the rock bolt can effectively reinforce the jointed-rock mass and reduce the possibility of local collapses of rocks, thus the importance of the rock bolt should not be overlooked, regardless of the overall stability.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2010년도 추계 학술발표회
• /
• pp.1060-1064
• /
• 2010

Ground anchors are mostly used to improve the resistance capacity of retaining walls. The end of the anchor is connected to retaining wall through tendons and the forces in tendons are transferred to ground. In this study, we plan that the new anchor system increases the tension force in tendons and improves the pullout resistance characteristics of the system. In order to increase the pullout resistance capacity of existing anchor system, the new anchor system is made by attaching four steel sticks to the tip of anchor end. So the field test results showed that the pullout resistance capacity of the wedge-shaped ground anchor was acceptable to elastic displacement range.

• 한국지반신소재학회논문집
• /
• 제16권4호
• /
• pp.241-249
• /
• 2017

보강토 구조물에서 흙과 보강재 상호작용은 접촉면 마찰저항 또는 보강재 인발저항에 의해 발생되며, 신장성 지오그리드 보강재의 인발정수를 측정하기 위하여 일반적으로 인발시험을 실시한다. 인발시험시 인발정수에 영향을 미치는 요소는 뒷채움재의 밀도, 보강재의 형상, 토피하중, 보강재의 포설길이 등이 있다. 본 연구에서는 인발시험시 합리적인 인발정수 산정을 위한 신장성 보강재의 포설길이를 제안하고자 인발시험을 실시하였으며, 보강재 포설길이는 각각 32cm, 52cm, 72cm, 100cm로 선정하였다. 인발시험결과 보강재 포설길이에 따른 인발정수의 영향을 분석하였으며, 인발시험에서 흙과 보강재사이의 마찰저항은 보강재 포설길이가 증가할수록 증가함을 확인하였다.

• 한국지반환경공학회 논문집
• /
• 제4권1호
• /
• pp.67-75
• /
• 2003

본 연구에서는, 기존 강재스트립 보강재의 표면마찰저항력 이외에도 지지저항력의 발휘가 동시에 예상되는 새로운 형태의 버팀재 볼트 접합형 강재스트립 보강재가 제시되었으며, 이에 대한 인발거동특성을 파악하기 위해 실내인발시험을 통하여 보강재의 폭, 상재하중의 크기 및 지지저항부재 유무 등이 흙과 보강재 사이의 마찰특성에 미치는 영향을 평가하였다. 또한 수동저항부재간의 상호간섭효과 등을 분석하기 위해, 지지저항부재의 설치개수와 위치 및 간격 등을 달리한 여러 조건 하에서 시험을 실시하였고, 이와 같은 시험결과를 바탕으로 하여 버팀재의 위치와 간격비에 따른 상호간섭의 영향 등이 고려된 인발저항계수 산정식을 제시하였다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 1999년도 토목섬유 학술발표회 논문집
• /
• pp.1-10
• /
• 1999

In the present study, laboratory pull-out tests with various geogrid shapes are carried out to investigate behavior characteristics of the geogrid. Also, an interface pullout formula is proposed for predicting and interpreting pullout test result. The analytical model is based on the assumption that the reinforcement is linear elastic during the pullout test. And then, maximum pullout force, frictional resistance and active length for each of the grid density ratio are predicted based on the interface pullout formula. The predicted results were compared with those of pullout tests, and showed in general good agreements.

• 한국지반신소재학회논문집
• /
• 제15권2호
• /
• pp.65-75
• /
• 2016

본 연구에서는 최근 적용사례가 급증하고 있는 가압식 그라우팅을 이용한 쏘일네일링의 현장인발시험 자료를 수집하여 데이터베이스를 구성하였으며, 기존의 도해법을 이용한 극한인발저항력 판정법의 문제점을 보완하기 위하여 비선형회귀분석을 이용하여 극한인발저항력을 판정하는 방법을 제안하였다. 비선형회귀분석에 의해 추정된 하중-변위곡선은 현장인발시험 자료와 매우 높은 상관성을 보였으며, 도해법에 의해 판정된 극한인발하중에 비해 평균 29% 정도 크게 판정되었다. 쏘일네일의 하중-변위곡선이 항복하중 이후에 급격한 변위를 보이는 경우에는 S자 성장곡선 회귀모형이 가장 적합하며, 인발하중과 변위의 증가량이 점진적으로 감소하는 파괴거동을 보이는 하중-변위곡선은 점근적 방법이 가장 적합한 회귀모형으로 평가되었다. 본 연구로부터 제안된 단위극한주면 마찰 저항력은 국내 지반특성과 가압식 그라우팅 공법의 특성이 반영된 것으로 해외 연구결과로부터 제시된 설계도표를 이용하던 문제점을 개선함으로써 독자적인 설계기준을 확보하는데 기여할 수 있을 것으로 기대된다.

• 한국해양공학회지
• /
• 제17권4호
• /
• pp.43-51
• /
• 2003

The resistance mechanism of anchor changes according to the types of anchor. Friction anchors are classified into tension and compression types. In this study, the characteristics and mechanism of pullout are analysed, and the design method of anchor and computer program for design are developed through compression test results of anchor body grout. The characteristics of compression anchor, compared with tension anchor, are summarized mainly as follows: (1) The effect of progressive failure of compression anchor body are much smaller than those of tension anchor during pullout of anchor: (2) The skin friction resistance is increased by Possion effect of grout (anchor body) during pullout of compression anchor.