• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.46 no.3
• /
• pp.60-68
• /
• 2009

This work proposes a 10b 200MS/s 65nm CMOS ADC for high-definition video systems such as HDTV requiring high resolution and fast operating speed simultaneously. The proposed ADC employs a four-step pipeline architecture to minimize power consumption and chip area. The input SHA based on four capacitors reduces the output signal range from $1.4V_{p-p}$ to $1.0V_{p-p}$ considering high input signal levels at a low supply voltage of 1.2V. The proposed three-stage amplifiers in the input SHA and MDAC1 overcome the low output resistance problem as commonly observed in a 65nm CMOS process. The proposed multipath frequency-compensation technique enables the conventional RNMC based three-stage amplifiers to achieve a stable operation at a high sampling rate of 200MS/s. The conventional switched-bias power-reduction technique in the sub-ranging flash ADCs further reduces power consumption while the reference generator integrated on chip with optional off-chip reference voltages allows versatile system a locations. The prototype ADC in a 65nm CMOS technology demonstrates a measured DNL and INL within 0.19LSB and 0.61LSB, respectively. The ADC shows a maximum SNDR of 54.BdB and 52.4dB and a maximum SFDR of 72.9dB and 64.8dB at 150MS/S and 200MS/s, respectively. The proposed ADC occupies an active die area of $0.76mm^2$ and consumes 75.6mW at a 1.2V supply voltage.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.46 no.3
• /
• pp.75-85
• /
• 2009

This work proposes a 13b 100MS/s 0.13um CMOS ADC for 3G communication systems such as two-carrier W-CDMA applications simultaneously requiring high resolution, low power, and small size at high speed. The proposed ADC employs a four-step pipeline architecture to optimize power consumption and chip area at the target resolution and sampling rate. Area-efficient high-speed high-resolution gate-bootstrapping circuits are implemented at the sampling switches of the input SHA to maintain signal linearity over the Nyquist rate even at a 1.0V supply operation. The cascode compensation technique on a low-impedance path implemented in the two-stage amplifiers of the SHA and MDAC simultaneously achieves the required operation speed and phase margin with more reduced power consumption than the Miller compensation technique. Low-glitch dynamic latches in sub-ranging flash ADCs reduce kickback-noise referred to the differential input stage of the comparator by isolating the input stage from output nodes to improve system accuracy. The proposed low-noise current and voltage references based on triple negative T.C. circuits are employed on chip with optional off-chip reference voltages. The prototype ADC in a 0.13um 1P8M CMOS technology demonstrates the measured DNL and INL within 0.70LSB and 1.79LSB, respectively. The ADC shows a maximum SNDR of 64.5dB and a maximum SFDR of 78.0dB at 100MS/s, respectively. The ABC with an active die area of $1.22mm^2$ consumes 42.0mW at 100MS/s and a 1.2V supply, corresponding to a FOM of 0.31pJ/conv-step.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.42 no.5
• /
• pp.134-147
• /
• 2014

Pleasure grounds, which were introduced during the Japanese colonial era, were places for organizing new amusement activities, and developed into a large-scale private spaces and a new type of public space at the same time. This study explores the scenery and accommodations of pleasure grounds and the changes of the amusement culture through the Wolmido Pleasure Grounds, which was a typical pleasure grounds of the time. At that time, Wolmido became a comprehensive amusement/entertainment place with many elements of both Western and Japanese pleasure grounds such as exotic buildings harmonized with trees, a beach, a seaside school, public playing field, and zoo constructed on the Island. Wolmido Pleasure Ground, which was connected with Kyungsung by Kyungin railroad during the Japanese colonial era, is a good example showing the process of the popularization and commercialization of the amusement culture. The process of popularization of amusement shows the spreading of the enjoyment of leisure time with amusement activities through appreciating the beautiful scenery of the pleasure grounds among various social classes. The caste system was broken and anyone could use the pleasure grounds by paying the fee, of which there were many kinds, so the distinction between genders and the different classes, such as the Chosun people and Japanese, regarding amusement in pleasure grounds disappeared gradually. Also, pleasure grounds were a place for Western hobby-sports activities and were the means to generalize collective and dynamic activities through summer school and various sport games. At the same time, there were places for deviation from the existing social norms when it was combined with entertainment facilities. The commercialization of amusement took place in the form of an artificial entertainment culture within an artificial environment. First, the scenery was artificially constructed and this scenery created the image of paradise such as 'captivating summer vacation spot' and 'water kingdom'. This was the result of the combined intentions of the colonial authority, the railroad company and the amusement corporation to produce economic profits and encourage development in the area. Second, an artificial spectacle was constructed using nature as the backdrop. Buildings of various styles created a modernized and exotic image when they were combined with each other. Artifacts such as breakwaters and arcades created new attractions for people that enabled them to view both nature and the crowds from a whole different perspective. Third, pleasure grounds contributed to the advent of passive users who would just follow the given use and instructions. In this way, one can find the prototype of popular entertainment places of today such as sightseeing complexes, amusement parks, and theme parks through the construction of amusement grounds as a place for providing dynamic activities.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.35 no.2
• /
• pp.161-169
• /
• 1999

This paper describes the swimming and escaping behavior of amber fish, Seriola aureovittata released in the first bag net of the setnet and observed with telemetry techniques. The setnet used in experiment is composed of a leader, a fish court with a flying net and two bag nets having ramp net. The behavior of the fish attached an ultrasonic depth pinger of 50 KHz is observed using a prototype LBL fish tracking system. The 3-D underwater position ofthe fish is calculated by hyperbolic method with three channels of receiver and the depth of pinger. The results obtained are as follows: 1. The fish released on the sea surface was escaped down to 15 m depth and rised up to near the sea surface during 5 minutes after release. The average swimming speed of the fish during this time was 0.87 m/sec. 2. The swimming speed of the fish is decreased slowly in relation to the time elapsed and the fish showed some escaping behavior forward to the fish court staying 1 to 7 m depth layer near the ramp net. The average speed of the fish during this time was 0.52 m/sec. 3. During 25 minutes after beginning of hauling net, the fish showed a faster swimming speed than before hauling and an escaping behavior repeatedly from the first ramp net to the second one in horizontal. In vertical, the fish moved up and down between the sea surface and 20 m depth. After this time, the fish showed the escaping behavior forward to fish court after come back to the first ramp net in spite of the hauling was continued. It is found that the fish was escaped from the first ramp net to the fish court while the hauling was carried out. The average speed of the fish after beginning of hauling was 0.72 m/sec which increased 38.5 ％ than right before the hauling and showed 0.44 to 0.82 m/see of speed till escaping the first bag net. The average swimming speed during observation was 0.67 m/sec (2.2 times of body length).

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.36 no.4
• /
• pp.299-308
• /
• 2000

A model experiment on the anchovy boat seine was carried out in the southern sea of korea to analyze the vertical opening and the underwater geometry. The model net A was made of half size in the length and width of the prototype net. The model net B was attached floats and chain to the model net-A. The vertical opening and the underwater geometry of the model net were determined by distance of Minilog position with the combinations of the distance between paired boats and the towing speed. The results obtained can be summarized as follows; 1. Vertical opening of the model net was gradually lowered according to the increase of the distance between paired beats and the towing speed. 2. Vertical opening of Wing net, In side wing net, Square, Fore bag net, Flapper and After bag net of the model net A according to the distance between paired boats were varied in the range of 10.8~9.0, 12.0~8.3, 12.6~9.0, 10.4~6.6, 4.6~5.2, 8.8~7.7m respectively, varied in the range of 36~30, 21~15, 31~22, 80~51, 80~96, 59~51% of the normal opening respectively 3. Vertical opening of Wing net, In side wing net, Square, Fore bag net, Flapper and After bag net of the model net B according to the distance between paired boats were varied in the range of 9.1~8.5, 9.8~6.5, 11.2~8.0, 11.0~8.1, 4.7~5.0, 7.0~7.5m respectively, varied in the range of 30~28, 18~12, 27~20, 85~62, 87~93, 47~50% of the normal opening respectively 4. Vertical opening of each a part of the model net according to the towing speed was as same as the former. 5. Model net was appeared apparent the pocket shape, because Wing net and Inside wing net was opened 30% of the normal opening. 6. The bosom and the bag net of the model net A were risen up to the upper lazer, this phenomenon was more apparent as the distance between paired boats and the towing speed increase, but the model net B was almost constant. 7. Working depth of the model net was gradually hallowed according to the increase of the distance between paired boats and the towing speed

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.16 no.1
• /
• pp.3263-3291
• /
• 1974

Experimental work of grain bin was carried out to develop the methods of natural air in-bin drying and storage. The method is considered to be more economical, labour saving, and an effective countermeasure to grain loss. To examine the possibility of farm use of the grain bin and to analyze the related factors concerned with in-bin grain drying and storage, ambient air conditions (especially the change of air temperature and relative humidity) and grain quality during drying and storage periods were investigated. A laboratory model bin was constructed to investigate the effect of different forced air conditions on the drying characteristics of rice. In addition, a grain bin with 2.2m diameter and 1.8m height, considered to be the optimum size for the average Korean farm, was constructed and tested to examine the drying and storing characteristics of rice. The weather data analyzed in this study was the nine-year (from 1964 to 1972) record of air temperature and relative humidity in the Suweon area, and the thirty-year (from 1931 to 1960) record of pentad normal relative humidity and air temperature in the Seoul area. From the results of the weather data analyses, the adequate air delivery hours (which was arbitrary defined as the condition to give less than 75% relative humidity) to dry the rice during October were about nine hours (from approximately 10 A.M. to 7 P.M, ) a day, in which the average air temperature was about 15.9$^{\circ}C$ and average relative humidity was 66%. The occurence of days having three hours of such conditions was 1, 2, and 1-day within the 1st, 2nd add last 10-day periods for the month of October, respectively. Therefore, it may be considered that the weather condition in October was satisfactory for the forced natural air drying. The results of the laboratory model bin test were analyzed to obtain the drying curve and drying rate for different drying stages and grain layers in the bin corresponding to various conditions of forced natural air. A drying experiment with a prototype grain bin showed that an approximate 5 percent grain moisture gradient through a 1.6 meter grain deposit was observed after 80 hours of intermittent drying, giving an over dried zone in the lower grain layers and an extremely high grain moisture zone in the upper layers. This indicates that an effective measure should be taken to reduce this high moisture gradient. In order to investigate the drying characteristics of bulk grain in a layerturning operation a grain bin test was performed. This showed a significant improvement of uniform drying. In this test, approximate 107 hours were required to dry a depth of 1.6 meter of grain from an initial moisture content of 22.2 percent to a moisture content of 16.7 percent using an air delivery rate of 2.8 cubic meter per a minute per every cubic meter of grain. This resulted in a 2 percent moisture gradient from the top to the bottom of the bin. During storage period, till the end of June the average temperature of grain was 2~3$^{\circ}C$ higher than ambient air temperature. But during July when the grain moisture content went up slightly (less than 1 percent), the average temperature of the grain also increased to 3~5$^{\circ}C$ higher than ambient air temperature. It is therefore recommended that for safe grain storage, grain should not be stored in sheet metal bins after mid May. From the above results, in-bin rice drying and storage can be used effectively on Korean farms. It is strongly recommended that the use of grain-bin system should be implemented for farm use to improve farm drying and storage of rice.

• Journal of Biosystems Engineering
• /
• v.1 no.1
• /
• pp.1-6
• /
• 1976

This paper is the third one of the study on balanced type oscillating mole-drainer, the first one was presented in No 9. Gyeongsang College Report and the second one in Vol. 17, No.4 of the KSAE. In the first part of this study, the characteristics of traction forces between the nonoscillating earth working equipments and oscillating ones was compared. A model of the balanced type oscillating mole-drainer, which composed of a mechanism that may reduce the machine vibration, was designed following the dimensional analysis and similitude technique. The model test was carried out to clarify the balancing mechanism of the oscillating parts and other parts of the machine. In the light of the results from the model tests, a prototype machine was made for experimental purpose. Results from the field test by a reported in the near future. In the second report, the model tests were carried out under the same soil conditions, i.e, . oscillating frequency, running velocity, and oscillating amplitude, etc. It was clear that use of balanced type oscillating model could substantially reduce the vibration of the whole system of the machine, when compared with the nonoscillating type model. In this paper(the third report), results of investigation on the traction force, power requirement, and moment. etc, is presented. Analysis of variance technique was used for analyzing the effect of the frequency, amplitude, and running velocity on the draft force, torque, power requirements, and moments. The results obtained from the model tests are as follows, 1) By practicing a balanced-type oscillating mole-drainer, it was possible to reduce the traction resistance by 55.1-61. 2 percent of traction resistance, however, was 1.75 - 1.95 times greater than the value of resistance which was induced by use of a mole-drainer with single bullet. The resistance of rear shank against soil was considered as a main causing factor of the above results. 2) As the oscillation frequency was increased, the traction resistance was decreased. Considering on the effect of oscillation the greater the amplitude, and the slower the running velocity was, the greater the reduction ratio of traction resistance was. 3) The ratio of the traction resistance of oscillating mole-drainer to that of non-oscillating one could be represented as a function of dimensionless variable (V/$Af$). The results from the tests were well agreed with the reported results from the experim ents on oscillation plow or hoe. 4) By taking a lower value of (V/$Af$), reducing the traction resistance was possible. This fact meant, however, that the efficiency of mole drain practice would be lower. 5) It was experimentally confirmed under the same condition of soil that the variable (R/$rD1^3$) could be represented as a function of a variable($V^2/gD$) when a non\ulcornerocillating mole-drainer was used. 6) When a oscillating mole-drainer was used, the variable(R/$rD_1^{3}$) could be represented as a function of two variables ($v^2/gD_1$) and (V^2/gD_1$). 7) The torque was not affected by a change of frequency. However, a relation of proportionality existed between torque and amplitude, running velocity, and ratio of bullet diameter. When a balanced type oscillating mole-drainer with two bullets was used, torque was increased by 52.8-78. 4 percent and total power requirement was also increased. 8) Total power requirement was increased linearly in accordance with the increasing frequency, 41.96 percent of total power was used for oscillating action. The magnitude of total power requirement was 1. 8-9. 4 times greater than that of a non-oscillating mechanism. In the view point of power requirement, it was not advisable to increase the frequency, amplitude, running velocity, and ratio of bullet diameter at the same time. 9) Only the positive moment occured in the rear shank. Change of the diameter of a rear bullet, could not affect the balancing against the soil resistance. It was necessary for rear bullet to have a large resistance against soil only when the rear bullet was in backward motion. 10) Within an extent of the experimental base, optimum limits for several design factors were A=0.5cm, $f$=22.5Hz, V=O. 05m/sec, and $\lambda$=1.0 By adapting these values traction resistance was reduced by 40 percent and vibration acceleration wa s reduced by 60 percent. Even though the total , power requirements for operating a balanced type oscillation mechanism was greater ~than that of non-oscillating one, using a oscillating mechanism would be more effective. Because a balanced type oscillating mechanism is used, tractive resistance will be reduced and then the lighter . tractive equipment could be used.

• Journal of the Korea Society of Computer and Information
• /
• v.8 no.2
• /
• pp.51-56
• /
• 2003

The structuring of Web information supports a strong user side viewpoint that a user wants his/her own needs on snooping a specific Web site. Not only the depth first algorithm or the breadth-first algorithm, but also the Web information is abstracted to a hierarchical structure. A prototype system is suggested in order to visualize and to represent a semantic significance. As a motivating example, the Web test site is suggested and analyzed with respect to several keywords. As a future research, the Web site model should be extended to the whole WWW and an accurate assessment function needs to be devised by which several suggested models should be evaluated.

• Journal of the Korean Institute of Traditional Landscape Architecture
• /
• v.34 no.3
• /
• pp.38-49
• /
• 2016

This study is based on the assumption that the documentations, and poetry form a basis for undertone of the location and original landscape explored by inference and enjoyment aspects; the significance has been inferred by investigating the original location, relocated location, and the original landscape of Imsil Manchwi Pavilion. The results of the attempted research for locational value, and preservation of the original landscape before and after the relocation of Imsil Manchwi Pavilion is as follows. Firstly, Manchwi, meaning evergreen, was made a pseudonym of KimWi. The name reflects an image two evergreen pine trees facing one another. The poetry form presents the eternal fidelity. In addition, considering the symbolic plant and the meaning of evergreen pine trees specified on the pavilion, the name is derived from the fidelity, longevity of the family, vitality and so on. Secondly, Manchwi Pavilion was founded in the location, known as the snakehead form, that represents the vitality. Snake faces the swallow form over the river, therefore, it connotes the wishes for fidelity and prosperity of the family. Manchwi Pavillion is prostrate pheasant form which is suitable for those who look for a hiding place or place for their study. It is noticeable that the location infers and hand down the efforts on succession for prosperity of the family and the study. Thirdly, it is estimated that Manchwi Pavilion was established between 1572 and 1582; and the relocation was conducted in the late 1880s. Fourthly, although eternal fidelity was presented in Manchwi Pavillion with locational language, the Manchwi Pavillion after its relocation next to KimWi's grave implies the tendency of the changed value: the commemoration of the ancestors, and prosperity of the family. Fifthly, after the relocation of the pavilion, the proportion of the rooms with Korean heating system, so-called'Ondol'has been increased for its best use in all seasons. And its veranda for extension and its verse couplet implies that this connote the original meaning and pursuit of the study. Sixthly, the way that the poetry portrays pine trees, pond, plants, valleys, and streams shows the aspect of enjoyment of the landscapes and the meaning of fidelity, pure mind, free and easy life, self-examination, the frailty of human life. Lastly, despite the difference between tenth poetic language of three Sipyoung and Wonwoon Sipyeong, exploring the landscape based on the analysis on the poetry can be a basis on the maintenance and restoration of the original landscape as the inspiration and the meaning show that Wonwoon Sipyeong maintains the aspect of the author enjoying original landscape.

• Journal of Intelligence and Information Systems
• /
• v.18 no.2
• /
• pp.47-60
• /
• 2012

Video data comes in the form of the unstructured and the complex structure. As the importance of efficient management and retrieval for video data increases, studies on the video parsing based on the visual features contained in the video contents are researched to reconstruct video data as the meaningful structure. The early studies on video parsing are focused on splitting video data into shots, but detecting the shot boundary defined with the physical boundary does not cosider the semantic association of video data. Recently, studies on structuralizing video shots having the semantic association to the video scene defined with the semantic boundary by utilizing clustering methods are actively progressed. Previous studies on detecting the video scene try to detect video scenes by utilizing clustering algorithms based on the similarity measure between video shots mainly depended on color features. However, the correct identification of a video shot or scene and the detection of the gradual transitions such as dissolve, fade and wipe are difficult because color features of video data contain a noise and are abruptly changed due to the intervention of an unexpected object. In this paper, to solve these problems, we propose the Scene Detector by using Color histogram, corner Edge and Object color histogram (SDCEO) that clusters similar shots organizing same event based on visual features including the color histogram, the corner edge and the object color histogram to detect video scenes. The SDCEO is worthy of notice in a sense that it uses the edge feature with the color feature, and as a result, it effectively detects the gradual transitions as well as the abrupt transitions. The SDCEO consists of the Shot Bound Identifier and the Video Scene Detector. The Shot Bound Identifier is comprised of the Color Histogram Analysis step and the Corner Edge Analysis step. In the Color Histogram Analysis step, SDCEO uses the color histogram feature to organizing shot boundaries. The color histogram, recording the percentage of each quantized color among all pixels in a frame, are chosen for their good performance, as also reported in other work of content-based image and video analysis. To organize shot boundaries, SDCEO joins associated sequential frames into shot boundaries by measuring the similarity of the color histogram between frames. In the Corner Edge Analysis step, SDCEO identifies the final shot boundaries by using the corner edge feature. SDCEO detect associated shot boundaries comparing the corner edge feature between the last frame of previous shot boundary and the first frame of next shot boundary. In the Key-frame Extraction step, SDCEO compares each frame with all frames and measures the similarity by using histogram euclidean distance, and then select the frame the most similar with all frames contained in same shot boundary as the key-frame. Video Scene Detector clusters associated shots organizing same event by utilizing the hierarchical agglomerative clustering method based on the visual features including the color histogram and the object color histogram. After detecting video scenes, SDCEO organizes final video scene by repetitive clustering until the simiarity distance between shot boundaries less than the threshold h. In this paper, we construct the prototype of SDCEO and experiments are carried out with the baseline data that are manually constructed, and the experimental results that the precision of shot boundary detection is 93.3% and the precision of video scene detection is 83.3% are satisfactory.