• Journal of the Korean Society for Precision Engineering
• /
• v.10 no.3
• /
• pp.125-132
• /
• 1993

On this study, magnetic force versus input currents is analyzed by modeling taper plunger type proportional electromagnet of ISC valve using the permernce method. And, the reliabiliy of simulation is verified by comparing the experimental values with the calaulate magnetic force. From the result of this study, it is found that the taper angles at plunger and core, the length of air gap between plunger and yoke are the prumary factors in designing taper plunget type proportional electromagnet. Magnetic force is decreased as a whole according to increasing the air gap between pluger and yoke, and vise versa. But, the magnetic force is not proportional to current, when the air gap is very small. In case of decreasing the taper angle of pluger, the stroke range of plunger where magnetic force is proportional to current becomes farther from core.

• Journal of Institute of Control, Robotics and Systems
• /
• v.15 no.10
• /
• pp.974-981
• /
• 2009

In this paper, a method of auto-tuning of PID (Proportional-Integral-Derivative) and PIDA (Proportional-Integral-Derivative-Acceleration) controllers is proposed that can be applied to a time-delayed second order model. The proposed identification method is based on step responses, but it can be easily automated rising digital controller unlike the existing graphical identification methods. We provide a ways to yield parameter identifications which is independent to initial values of the plants. The tuning rule is based on the pole-placement strategy and is formulated so that it can be implemented using a digital controller with ease.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.5 s.176
• /
• pp.1352-1361
• /
• 2000

We obtain a micromechanics-based Helmholtz free energy and then in the framework of irreversible thermodynamics, a kinetic relation, a martensitic nucleation criterion and the reorientation criterion of martensitic variants are obtained. These relations are valid for a three-dimensional proportional and non-proportional loadings and for a combination of mechanical and thermal loading. From the simulated pseudoelastic stress-strain relation of a single crystal with loading rate effect, polycrystalline behavior in case of proportional and non-proportional loading is predicted by a homogenization method. The obtained results are compared quantitatively with experimental results.

• Transactions of The Korea Fluid Power Systems Society
• /
• v.7 no.4
• /
• pp.23-31
• /
• 2010

As the analysis and design technologies for electro-magnetic actuation has advanced over the years, proportional solenoid valve is gaining acceptance in wide range of industrial and commercial applications because of its superior characteristics over the conventional AOV or MOV, such as improved performance, reduced maintenance costs. This research deals with the position controller design of two-stage flow control solenoid valve. Investigation of steady-state characteristics and dynamic model identification for pilot disc is performed. Least square method to minimize the error magnitude of frequency response between the closed-loop and target system is applied to the design of PI-controller gains. From the experiments of step and frequency response, it is concluded that the controller meets the performance specification of target system, which verifies the usefulness of controller design method for proportional solenoid valve.

• Journal of Electrical Engineering and Technology
• /
• v.9 no.5
• /
• pp.1746-1752
• /
• 2014

This paper presents an application of proportional-resonant (PR) current controllers in modular multilevel converter-high voltage direct current (MMC-HVDC) system under unbalanced voltage conditions. The ac currents are transformed and controlled in the stationary reference frame (${\alpha}{\beta}$-frame). Thus, the complex analysis of the positive and negative sequence components in the synchronous rotating reference frame (dq-frame) is not necessary. With this control method, the ac currents are kept balanced and the dc-link voltage is constant under the unbalanced voltage fault conditions. The simulation results based on a detailed PSCAD/EMTDC model confirm the effectiveness of the proposed control method.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.44 no.6
• /
• pp.21-28
• /
• 2007

Using multi-resolution, the mutiresolution proportional-integral-derivative(MRPID) controller functions as a filter to eliminate noise and disturbance which are included in error signals. If the sampling frequency is high, the response time will be delayed because of the remaining high frequency component although the overshoot is removed. However, if the sampling frequency is low, the response time will be enhanced by getting rid of signal components while the overshoot is increased. In this paper, the sampling frequency tuning method is used the response of the proportional integral derivative(PID) controller and the MRPID controller, and the parameter tuning method is considered the characteristic of the MRPID controller. The proposal method is verified by computer simulations.

• Journal of Drive and Control
• /
• v.13 no.3
• /
• pp.47-52
• /
• 2016

This paper presents a control method for the performance improvement of a proportional solenoid actuator using a Pulse Width Modulation (PWM) signal. It is very difficult to obtain excellent response performance from a proportional solenoid actuator using a simple proportional controller with no PWM signal or dither because the mass and structure of a proportional solenoid actuator changes according to the application target, friction force in the proportional solenoid tube, operating force and displacement range. To solve the above problems, first, a controller with a PWM function for experimenting with attraction force characteristics was designed and manufactured. Secondly, an experimental setup for solenoid performance measurement with a force sensor and a displacement sensor was also manufactured. The attraction force characteristics according to the frequency and duty ratio variations of a PWM signal were tested and the relationships among the frequency, duty ratio, plunger mass and friction characteristics were analyzed. Finally, response characteristics improvements for proportional solenoid actuators are discussed.

• Proceedings of the KSR Conference
• /
• 2004.10a
• /
• pp.411-416
• /
• 2004

This paper introduces a fast Fourier transform (FFT)-based spectral analysis method for the transient responses as well as the steady-state responses of linear dynamic systems with non-proportional damping. The force vibration of a non-proportionally damped three-DOF system is considered as the illustrative numerical example. The proposed spectral analysis method is evaluated by comparing with the numerical solution obtained by the Runge-Kutta method

• Journal for History of Mathematics
• /
• v.19 no.2
• /
• pp.101-114
• /
• 2006

The content and method of geometry taught in secondary school is rooted in 'Elements' by Euclid. On the other hand, however, there are differences between the content and structure of the current textbook and the 'Elements'. The gaps are resulted from attempts to develop the geometry education. Specially, the content and method for the proportional relations of geometric figures has been varied. In this study, we reviewed the changes of the proportional relations of geometric figures with pedagogical point of view. The conclusion that we came to is that the proportional relations in incommensurable case Is omitted in secondary school. Teacher's understanding about the proportional relations of geometric figures is needed for meaningful geometry education.

• Journal of the Korea Society for Simulation
• /
• v.25 no.4
• /
• pp.13-20
• /
• 2016

Microsimulation model has aimed to simulate the impact of policy at the level of individual and household. Recently, microsimulation model has been widely accepted in OECD countries for evaluating their economic and social policies. For improving the availability of microsimulation model, the population data which shows good accordance with the official statistics should be required. In this paper, we generate Korean synthetic populations by using the iterative proportional updating method. For the validation of Korean synthetic populations, we compute the difference between the generated synthetic populations and the summary table of Korean census. Then, we confirm that it shows good accordance with the summary table.