• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.67 no.11
• /
• pp.1434-1446
• /
• 2018

This paper presents new speed control strategy for periodic load torque injected in AC motor. If motor drive system has a periodic load torque, it causes a periodic motor speed ripple bringing about vibrations and noises. This paper proposed new control method consisting of PIR(proportional-integral-resonant) controller and repetitive controller. PIR controller controls DC, low frequency and fundamental components and repetitive controller controls other harmonics. The performance has been verified through computer simulations using MATLAB Simulink and experiments.

• Journal of Power Electronics
• /
• v.14 no.6
• /
• pp.1217-1223
• /
• 2014

A novel half load-cycle worked dual input single output (DISO) DC/AC inverter is presented. The basic circuit consists of a dual buck regulator, which works in continuous current mode. The working principle of DISO DC/AC inverter has been used. The control method applied for half load-cycle worked DISO DC/AC inverter has been studied. The control effects of the open-loop proportional control and closed-loop proportional-integral control are compared by using PSIM software. The parameters are adopted in the realistic simulation and experiment test. Moreover, the waveforms, such as voltage of modulation reference signal and output voltage, were given. The simulation and experiment results proved that the half load-cycle worked DISO DC/AC inverter could achieve good performance, gain a line frequency of 50 Hz, and verify the correctness of theoretical analysis.

• 제어로봇시스템학회:학술대회논문집
• /
• 2005.06a
• /
• pp.186-189
• /
• 2005

In a clinical setting, developing a reliable method for the automated drug infusion system would improve a drug therapy under the unexpected and acute changes of hemodynamics. The conventional proportional-integral-derivative (PID) controller might not be able to achieve maximum performance because of the unexpected change of the intra- and inter-patient variability. The fuzzy PID control and the conventional PID control were tested under the unexpected response of mean arterial blood pressure (MAP) to a vasopressor agent during acute hypotension. Compared with the conventional PID control, the fuzzy PID control performed the robust MAP regulation regardless of the unexpected MAP response (average absolute value of the error between target value and actual MAP: 0.98 vs. 2.93 mmHg in twice response of the expected MAP and 2.59 vs. 9.75 mmHg in three-times response of the expected MAP). The result was due to the adaptive change of the proportional gain in PID parameters.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.04a
• /
• pp.363-367
• /
• 1996

The robustness issues in fault detection and isolation(FDI) have received considerable attenuation in recent years, due to the increasing demand for safe and reliable operation of uncertain and complex dynamic systems. The aim of this paper is to present the FDI method by using proportional integral(PI) observer and unknown input observer(UIO) under the faults of actuators and sensors. Due to this simple residual generator, the PI observer can easily detect the both faults of actuator and sensor. A simulation results show the effectiveness of this methods.

• Journal of Institute of Control, Robotics and Systems
• /
• v.5 no.6
• /
• pp.656-666
• /
• 1999

In this paper, we design the optimal PD control system which has the robust performance. This PD control system is designed by applying genetic algorithm (GA) to the determination of proportional gain KP and derivative gain KD that are given by PD servo controller, to make the output of plant follow the output of reference model optimally. These proportional and derivatibe gains are simultaneously optimized in the search domain guaranteeing the robust performance of system. And, this PD control system is compared with $\mu$ -synthesis control system for the robust performance. The PD control system designed by the proposed method has not only the robust performance but also the better command tracking performance than that of the $\mu$ -synthesis control system. The effectiveness of this control system is verified by computer simulation.

• Tribology and Lubricants
• /
• v.15 no.1
• /
• pp.17-23
• /
• 1999

A Gerotor hydraulic motor is a planar mechanism consisting of a pair of rotors one of which encloses another rotor. The motion of the inner-rotor relative to the outer-rotor is produced by the pressure difference between the adjacent chambers. A design method of inner-rotor tooth profile using unit tangential vectors is presented in this work. Based on the relationships derived, the influence of the eccentricity of inner-rotor and the radius of circular arc tooth on the flow rate, torque and curvatures were investigated. It was shown that the flow rate and mean torque is proportional to eccentricity, but inversely proportional to the radius of circular arc teeth. Also, the maximum value of the equivalent curvature is increased as the eccentricity and the radius of circular arc teeth increased.

• Proceedings of the KIEE Conference
• /
• 1997.11a
• /
• pp.119-121
• /
• 1997

This paper suggests a design method of the robust model following PD control system using genetic algorithm. This PD control system is designed by applying genetic algorithm with reference model to the optimal determination of proportional and derivative gains that are given by PD servo controller. These proportional and derivative gains are optimized simultaneously in the search domain guaranteeing the robust stability of closed-loop system satisfying different stability margins. The effectiveness of this PD control system is verified by computer simulation.

• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.1779-1780
• /
• 2008

This paper presents a switching system of speed controller between PI (Proportional_Integrator) and P_LPF (Proportional_Low pass filter) to improve overshoot and slow settling time in DC motor. When the integrator is saturated in the PI controller, the error signal is integrated continuously. For preventing the state, the Anti-windup scheme is proposed. But the Anti-windup scheme dose not show stable characteristics in the whole speed command section after tuned a gain. By using P_LPF switching system these problems are improved and there is no need to tune of user hereafter, when the integrator is saturated. The proposed method is verified by the simulation results using MATLAB SIMULINK.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.39 no.2
• /
• pp.192-198
• /
• 1990

The performance of the proportional navigation guidance(PNG) law for a target with constant acceleration has been extensively studied in the prior literature. In this papaer, we consider the performance of the PNG law for a randomly maneuvering target. By means of Lyapunov method, we prove that an ideal missile guided by the conventional PNG law can always intercept a randomly maneuvering target if the initial missile heading error is small and the navigation constant is chosen sufficiently large. To the authors' best knowledge, this is the first analytic result on the performance of the PNG law for a target with time-varying acceleration.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.10a
• /
• pp.230-233
• /
• 2004

The purpose of this study is to establish the optimal induction heating conditions of various preform types used for TR forging. The finite element model coupled electro-magnetic and transient heat transfer was employed to evaluate the distribution of temperature at the billet. Power control method was applied to control temperature of preform in induction heating because TR forging is not a continuous process. Power schedule that consists of heating and holding stage was suggested. In heating stage, power is inversely proportional to diameter of preform but the time of heating stage is directly proportional to the diameter of preform. But, in holding stage, the required power for thermal equilibrium per unit volume of the billet decreases with an increase in a diameter of billet due to the increase of efficiency.