• Journal of Biosystems Engineering
• /
• v.6 no.2
• /
• pp.48-57
• /
• 1982

In order to improve the quality of traditionally sun-dried red peppers and to increase the efficiency of drying performance, three types of solar dryers were designed and built, and drying performance of the solar dryers was compared to traditional sun drying. Results obtained from the experiment are summarized as fallows: 1. The air temperature and relative humidity profiles over a 8-hour period measured at the specified locations in the drying chamber of solar dryers appeared to have large variation in each dryer. The rate of drying increased with the temperature rise in the drying chamber of the solar dryer. 2. In general. drying with solar dryers proceeded faster than traditional sun drying. With A'-type of solar dryer developed in the second experiment it was possible to dry red peppers in seven days from an initial moisture content of 80% to safe storage conditions. The drying time with the A'-type solar drier was 50% shorter compared to traditional sun drying. 3. Red peppers appeared to have an increasing or constant-rate drying period until the weight of the product was reduced to about one half the initial weight, followed by a falling-rate drying period. When the dried red peppers were exposed to the atmospere during the night, the moisture content increased as much as 6%, which is much higher than for the grains. 4. It was suggested from the experiment that either a heat storage system or a supplemental heating system in the solar dryer was desirable for more efficient drying operation. 5. It was shown that the solar dryer developed in this study may be suitable for drying other vegetables and fishes, and also offered additional advantages of saving in drying time, maintaining sanitation and minimizing contamination by dust, insects and unfavorable weather condition.

• Journal of the Mineralogical Society of Korea
• /
• v.9 no.1
• /
• pp.1-6
• /
• 1996

Woolastonite from Susan occurs as intercalations in limestone beds of Lower Paleozoic Joseon Supergroup. It is a thermal metamorphic product of impure limestone. Electron microprobe analysis shows that it is considerably pure wollastonite. It has triclinic cell with a=7.932$\AA$, b=7.328$\AA$, c=7.069$\AA$, $\alpha$=89.995$^{\circ}$, $\beta$=$95.255^{\circ}$, and $ \Upsilon=103.367^{\circ}$.Dissolution behaviors of wollastonite have been studied conducting three different dissolution experiments; two different reactions with HC1 (one batch and one re-initialization experiment) and one traction with distilled water. In the batch type powder wollastonite-HCl reaction, pH of solution rapidly increases in the early stage and then its rate of increase slows down to reach plateau resulting in parabolic relationship with time. It is represented by the early rapid rise and fall in pH giving a sharp pH-edge and succeeding slow rise in the re-initialization experiment. The early rapid rise in pH is due to the rapid sorption of H- in solution to oxygens on the reactive surface of wollastonite and the fall in pH means that all reactive surface sites are occupied by H- ions and no more H- adsorption occurs. The slow rise in pH following the pH- edge is due to the dissolution of wollastonite as evidenced by the correlation of pH variation and cation concentration. Dissolution of powder wollastonite in HCl shows linear trend with time. Si is dissolved predominantly over Ca at a constant rate. Ca is dissolved predominantly in the very early stage. Dissolution rate of coarse-grained wollastonite fragments in distilled water is parabolic with times howing a rapid reaction in the early stage and a slow reaction in the advanced stage. The Ca/Si ratio in solution is high in the case of coarse-grained wollastonite fragment as compared with powder wollastonite. The coarse-grained wollastonite fragment-water (acid) reaction resulted in the solution with an elevated constant pH value (alkaline) giving an important significance on the environmental view point.

• Korean Chemical Engineering Research
• /
• v.56 no.3
• /
• pp.315-319
• /
• 2018

Fenton reaction is widely used as a out of cell method for evaluating the membrane electrochemical durability of Proton Exchange Fuel Cell (PEMFC). In this study, we investigated the factors affecting the Fenton reaction. In order to estimate the degree of the reaction, it is necessary to analyze the radicals as a product in the Fenton reaction. However, since the radicals are difficult to analyze, the degree of the reaction was measured by analyzing the concentration of hydrogen peroxide. The activation energy was calculated from the rate of hydrogen peroxide change with temperature. The activation energy was 24.9 kJ/mol at 180 min. The Fenton reaction rate was affected by the iron ion concentration. At $80^{\circ}C$, 200 rpm, and $Fe^{2+}$ 80 ppm, the concentration of hydrogen peroxide was decreased more than 20% even for 1 hour, which shows that frequent solution replacement increases the membrane degradation rate.

• Resources Recycling
• /
• v.26 no.3
• /
• pp.39-46
• /
• 2017

AlN powder was prepared by carbon reduction and subsequent nitridation method through lab- scale experiments. AlN powder was synthesized using the mixture of high purity $Al_2O_3$ powder and carbon black at $1,600{\sim}1,700^{\circ}C$ for 0.5~6 hours under nitrogen atmosphere (flow rate of nitrogen gas: $4.7{\times}10^{-6}{\sim}20{\times}10^{-6}m^3/sec$) with variation of charged height of the mixture powder. Experimental results showed that size of the synthesized particles grows with increasing of temperature. The reaction activation energy was calculated as 382 kJ/mol at the temperature range, and it was considered that chemical reaction is the rate determining step. Content of oxygen and nitrogen of the prpared samples were 0.71~0.96 wt% and 30.7~35.1 wt%. The results was similar with those of the commercial AlN product.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.37 no.8A
• /
• pp.712-719
• /
• 2012

This paper presents Single-bit Third order Delta-Sigma Modulator, which can be applied to the Low speed High resolution ADC in Audio signal Process System. Whereas the Operational Amplifier in modulator consumed static power dissipation in operating, this modulator used Switching on/off techniques, which makes the Power dissipation of the modulator reduced. Also proposed modulator minimizes frequency characteristic variation by optimizing switch position. And this modulator chooses Single-bit type to guarantee stability. The designed ADC went through 0.35um CMOS n-well 1-poly 4-metal process to be a final product, and the final product has shown 17.1mW of power dissipation with 3.3V of Supply Voltage, 6.4MHz of conversion rate. And 84.3dB SNDR and 13.5bit ENOB with 20KHz of input frequency.

• Design & Manufacturing
• /
• v.8 no.1
• /
• pp.10-13
• /
• 2014

Plastic products are producted more than 70% of total processes by the injection molding. The injection molding process has 4 processes such as filling, packing, cooling and ejecting. It spends most of times in the cooling process. Therefore, it is important to control the mold temperature in producing plastic products. The time and system of cooling affect the product's quality and productivity. Especially, cooling time has about 60% of total injection cycle time. Therefore, we can improve a productivity by shortening cooling time. This study shows comparative study about cooling efficiency of spiral channel and baffle and observed the variation of time to freeze of molding As the result of CAE experiments, cooling rate by spiral channel had faster than baffle and as freeze time was decreased. Results of this study will be used widely to design for cooling system of injection mold.

• International conference on construction engineering and project management
• /
• 2005.10a
• /
• pp.527-532
• /
• 2005

The construction industries are facing problems of productivity, quality of work, safety, and the completion of projects in time. In construction industry a worker is exposed to hazardous environment, and has to do more physical work, effecting his health and also productivity. The automation and robotics can offer solution to many problems of the industry. In the past the major barrier to construction automation is the lack of electronic components and systems. This is solved now with the development of information technology, and the current obstacle is the high cost of automated systems, shortage of public money for R&D, and problems of acceptance. The robots employed in construction have followed the same concept as those employed in manufacturing. However, construction industry requires a different kind of robot compared to manufacturing Industry. The robots are stationery and product moves along the assembly line in manufacturing sector, but construction robots have to move about the site because buildings are stationary and of large size. The construction robots must function in adverse weather conditions, including variation in humidity, and temperature and increase the overall construction productivity rate. The major objective of the paper is to review the existing applications of building robots and to assess their implementation in building industry. A case study is considered for the implementation of robots for the painting work of the University Building at Saifabad PG College of Science, Hyderabad, India.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.21 no.1
• /
• pp.99-106
• /
• 2013

DME (Di-Methyl Ether) is synthetic product that is produced through dehydration of methanol or a direct synthesis from syngas. And it is able to save fossil fuel and reduce pollutants of emission such as PM and $CO_2$. In spite of its advantages it is difficult to design DME fuelled engine system because DME fuel may cause to severely generate cavitation and corrosion in fuel delivery system due to physical properties of DME. Therefore, in this study three-dimensional internal flow characteristics with consideration of cavitation were predicted in the DME injector using diesel and DME fuel. Moving grid technique was employed to describe needle motion and 1-D hydraulic simulation of injector was also simulated to obtain transient needle motion profiles. The results of simulation show that cavitations was generated at the inlet of nozzle near high velocity region both diesel and DME. And mass flow rate of DME is reduced by 4.73% compared to that of diesel at maximum valve lift because cavitation region of DME is much more larger. To increase flow rate of DME injector, internal flow simulation has been conducted to investigate the nozzle hole inner R-cut effect. The flow rates of diesel and DME increase as R-cut increases, and flow coefficient of DME fuel injector was increased by 6.3% on average compared with diesel fuelled injector. Finally, optimum shape of DME injector nozzle is suggested through the comparison of flow coefficient with variation of nozzle hole inner R-cut.

• Journal of Preventive Medicine and Public Health
• /
• v.11 no.1
• /
• pp.123-127
• /
• 1978

The major objective of this research is to identify those hospital characteristics that best explain cost variation among hospitals and to formulate linear models that can predict hospital costs. Specific emphasis is placed on hospital output, that is, the identification of diagnosis related patient groups (DRGs) which are medically meaningful and demonstrate similar patterns of hospital resource consumption. A casemix index is developed based on the DRGs identified. Considering the common problems encountered in previous hospital cost research, the following study requirements are estab-lished for fulfilling the objectives of this research: 1. Selection of hospitals that exercise similar medical and fiscal practices. 2. Identification of an appropriate data collection mechanism in which demographic and medical characteristics of individual patients as well as accurate and comparable cost information can be derived. 3. Development of a patient classification system in which all the patients treated in hospitals are able to be split into mutually exclusive categories with consistent and stable patterns of resource consumption. 4. Development of a cost finding mechanism through which patient groups' costs can be made comparable across hospitals. A data set of Medicare patients prepared by the Social Security Administration was selected for the study analysis. The data set contained 27,229 record abstracts of Medicare patients discharged from all but one short-term general hospital in Connecticut during the period from January 1, 1971, to December 31, 1972. Each record abstract contained demographic and diagnostic information, as well as charges for specific medical services received. The 'AUT-OGRP System' was used to generate 198 DRGs in which the entire range of Medicare patients were split into mutually exclusive categories, each of which shows a consistent and stable pattern of resource consumption. The 'Departmental Method' was used to generate cost information for the groups of Medicare patients that would be comparable across hospitals. To fulfill the study objectives, an extensive analysis was conducted in the following areas: 1. Analysis of DRGs: in which the level of resource use of each DRG was determined, the length of stay or death rate of each DRG in relation to resource use was characterized, and underlying patterns of the relationships among DRG costs were explained. 2. Exploration of resource use profiles of hospitals; in which the magnitude of differences in the resource uses or death rates incurred in the treatment of Medicare patients among the study hospitals was explored. 3. Casemix analysis; in which four types of casemix-related indices were generated, and the significance of these indices in the explanation of hospital costs was examined. 4. Formulation of linear models to predict hospital costs of Medicare patients; in which nine independent variables (i. e., casemix index, hospital size, complexity of service, teaching activity, location, casemix-adjusted death. rate index, occupancy rate, and casemix-adjusted length of stay index) were used for determining factors in hospital costs. Results from the study analysis indicated that: 1. The system of 198 DRGs for Medicare patient classification was demonstrated not only as a strong tool for determining the pattern of hospital resource utilization of Medicare patients, but also for categorizing patients by their severity of illness. 2. The wei틴fed mean total case cost (TOTC) of the study hospitals for Medicare patients during the study years was $11,27.02 with a standard deviation of $117.20. The hospital with the highest average TOTC ($1538.15) was 2.08 times more expensive than the hospital with the lowest average TOTC ($743.45). The weighted mean per diem total cost (DTOC) of the study hospitals for Medicare patients during the sutdy years was $107.98 with a standard deviation of $15.18. The hospital with the highest average DTOC ($147.23) was 1.87 times more expensive than the hospital with the lowest average DTOC ($78.49). 3. The linear models for each of the six types of hospital costs were formulated using the casemix index and the eight other hospital variables as the determinants. These models explained variance to the extent of 68.7 percent of total case cost (TOTC), 63.5 percent of room and board cost (RMC), 66.2 percent of total ancillary service cost (TANC), 66.3 percent of per diem total cost (DTOC), 56.9 percent of per diem room and board cost (DRMC), and 65.5 percent of per diem ancillary service cost (DTANC). The casemix index alone explained approximately one half of interhospital cost variation: 59.1 percent for TOTC and 44.3 percent for DTOC. Thsee results demonstrate that the casemix index is the most importand determinant of interhospital cost variation Future research and policy implications in regard to the results of this study is envisioned in the following three areas: 1. Utilization of casemix related indices in the Medicare data systems. 2. Refinement of data for hospital cost evaluation. 3. Development of a system for reimbursement and cost control in hospitals.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.6 no.4
• /
• pp.103-111
• /
• 2012

One of the basic physical properties of the hardened cement paste, the rigidity, is deteriorated during concrete matrix forming, depending on the replacement rate of the crushed stone powder, and due to drying shrinkage. Therefore, the concrete containing crushed stone powder has been limitedly used as non-structural construction material. To improve these disadvantages, a hydrothermal reaction employing method can be considered. High-temperature and high-pressure water is involved in the hydrothermal reaction in the mixing with specific materials. The rigidity improving mechanism is related to the synthesis of calcium silicate. The calcium silicate is produced through reaction between calcium compounds and the silicic acid. Various kinds of calcium silicate can be produced depending on the CaO/$SiO_2$ mole ratio, the temperature of the hydrothermal synthesis, the pressure, and the reaction time. The product of the synthesis mechanism, tobermorite crystal, plays a pivotal role for the rigidity reinforcement. The crushed stone powder, analyzed in this study, contains 50 to 60% of $SiO_2$ and 10 to 20% $Al_2O_3$. The composite rate is appropriate to create the tobermorite crystal through formation of hardened cement matrix under the hydrothermal synthetic conditions and with the CaO in the cement. Moreover, further reinforcement was promoted using the property of material under the identical density through promoting the formation of tobermorite crystal.