• Microbiology and Biotechnology Letters
• /
• v.38 no.3
• /
• pp.308-314
• /
• 2010

This study was conducted to investigate the characteristics and concentrations of ammonia produced from the livestock swine nightsoil treated with or without the livestock - environment improving agents. Odor generating device made of acryl was made by volume of 96 L to sample the ammonia odor. When swine night soil was placed in the device, concentration of ammonia averaged out at about 23.4 ppmv and ranged from 16 ppmv to 40 ppmv. Removal efficiencies of them showed 50% to 90% as compared to initial level before spraying, when the spray type agents were used immediately after they purchased. The persistence of the efficiency was retained for first two days. Among the agents, the natural deodorant showed the best efficiency of 87 to 99%. To evaluate the effects of 5 kinds of dietary probiotic powders, the experiments were conducted and based dietary treatments without antibiotics on growing piglets. In experiments, 60 piglets ($6.3{\pm}0.2\;kg$) were subjected to a 35-day feeding trial in which the effects of the dietary probiotic powder on the ammonia emission were compared. The ammonia gas emission was measured for every week. Ammonia emission from the swine nightsoil obtained from piglets supplemented with the probiotics power was lower than that of the nightsoil obtained from pigs in the control treatment (without probiotics). In ammonia removal efficiencies of the experimental groups, some products showed from 71% to 99% removal efficiencies throughout the entire period as compared to the control group. On the other hand, initial reduction of ammonia in some product was effective temporarily. After then, it did not show any reduction efficiency of ammonia.

• Journal of the Korean Applied Science and Technology
• /
• v.33 no.1
• /
• pp.75-82
• /
• 2016

The technology of fast pyrolysis is regarded as a promising route to convert lignocellulose biomass into bio-oil which can be upgraded to transportable fuels and high quality chemical products. Despite these promises, commercialization of bio-oil for fuels and chemicals production is limited due to its notoriously undesirable characteristics, such as high and changing viscosity, high water and oxygen contents, low heating value and high acidity. Therefore, in this study quality improvement of bio-oil through vaccum distillation had been targeted. A 600 g of cork oak(Quercus variabilis) which grounded 0.8~1.4 mm was processed into bio-oil via fast pyrolysis for 1.64 seconds at $465^{\circ}C$ and temperature of vaccum distillation(100hPa) was designed to control, $40^{\circ}C$, 50, 60, 70, and 80 for 30min. Bio-oil, biochar, and gas of pyrolytic product were produced to 62.6, 18.0 and 19.3 wt%, respectively. The water content, viscosity, HHV(Higher Heating Value) and pH of bio-oil were measured to 0.9~26.1 wt%, 4.2~11.0 cSt 3,893~5,230 kcal/kg and 2.6~3.0, respectively. Despite these quality improvement, production was still limited due to its notoriously undesirable characteristics, therefore continous quality improvement will be needed in order to use practical fuel of bio-oil.

• Korean Chemical Engineering Research
• /
• v.46 no.1
• /
• pp.82-87
• /
• 2008

$N_2O$ decomposition characteristics of dual bed mixed metal oxide catalytic system was investigated. The partial oxidation of methane at first reactor of dual bed catalytic system was performed over Co-Rh-Al (1/0.2/1) catalyst under the optimized condition of $8,000h^{-1}$ GHSV, gas ratio ($CH_4:O_2=5:1$) at $500^{\circ}C$. In the dual bed system investigated herein, the second catalyst bed was employed for the $N_2O$ decomposition using product of partial oxidation of methane at first bed. An excellent $N_2O$ conversion activity even at lower temperature ($<250^{\circ}C$) was obtained with Co-Rh-Al (1/0.2/1) or Co-Rh-Zr-Al (1/0.2/0.3/1) catalyst by combining Co-Rh-Al (1/0.2/1) hydrotalcite catalyst for the partial oxidation of methane in a dual-bed system. The $N_2O$ conversion activity is drastically reduced in the presence of oxygen in second bed of a dual-bed system over Co-Rh-Al (1/0.2/1) catalyst at $300^{\circ}C$.

• Korean journal of applied entomology
• /
• v.56 no.4
• /
• pp.395-402
• /
• 2017

Overuse of synthetic pesticides caused negative side-effects such as environmental contamination, development of insect pests' resistance, and effects on non-target organisms. Plant origin substances without/or with low mammalian toxicity have been considered as promising alternatives to the synthetic pesticides. Fumigant toxicity of the essential oil of Iranian Yarrow, Achillea millefolium L., was investigated against a cosmopolitan stored-product insect pest: saw-toothed grain beetle (Oryzaephilus surinamensis L.). Chemical profile of this essential oil was studied by Gas Chromatography-Mass Spectrometry. Tested concentrations were significantly effective to the mortality of insect pest. A positive correlation between essential oil concentrations and pest mortality were realized. LC50 value (lethal concentration needed to 50% mortality) was achieved as $17.977(16.195{\pm}20.433){\mu}l/l$ air. The main components were 1,8-Cineole (13.17%), nerolidol (12.87%), ${\alpha}$-cubebene (12.35%), artemisia ketone (6.69%), ${\alpha}$-terpineol (5.27%), alloaromadendrene oxide (4.71%) and borneol (3.99%). Terpenic compounds including monoterpene hydrocarbons (8.19%), monoterpenoids (44.23%), sesquiterpene hydrocarbons (21.69%) and sesquiterpenoids (22.24%) were 96.35% of the total identified compounds. Results indicated that the terpene-rich A. millefolium essential oil may be considered as a safe bio-agent in the O. surinamensis management.

• Food Science and Preservation
• /
• v.14 no.4
• /
• pp.369-377
• /
• 2007

This study investigated the effect of ginseng products on the baking properties of white breads. Flour was substituted by ginseng products (ginseng at levels 2, 4, 6, and 8%, all w/w, of flour levels). Both ginseng powder (GP) and red ginseng powder (RGP) were used. Similarly, red ginseng extract (RGE) was substituted at levels of 1, 2, 3, and 4% (all w/w) of flour. The physical properties of each dough were assessed using farinograms, extensograms, and amylograms. Water absorption increased as the proportions of ginseng products rose. The dough surface areas and R/E (resistance/extensibility) values decreased, as did peak viscosities, at the proportions of ginseng products increased. The pH values during fermentation decreased as the proportions of ginseng products increased. The fermentation power of dough with GP was lower than that of control, and higher than that of dough with RGP or RGE, but the addition of ginseng products beyond certain levels weakened the gas retention power: The specific loaf volumes of breads with 2% GP were the highest at 5.41 mL/g. In breads with RGE, the specificloaf volume increased from 5.52 mL/g to 5.82 mL/g as RGE levels rose from 0% to 4%. Hardness increased with rising GP and RGP levels in breads with GP and RGP, but decreased with RGE levels in breads with RGE. The moisture contents of breads during storage tended to be higher than control in breads with ginseng products. Lightness increased with addition of GP and decreased upon addition of RGP or RGE, while redness and yellowness increased after addition of any ginseng products. In sensory evaluation tests, the sensory scores for texture, color, mouth feel, and overall acceptability, were high, when any ginseng product (GP, RGP or RGE) was present at 2%. Of these breads, the bread with 2% RGE attained the highest sensory score.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.5 no.1
• /
• pp.103-110
• /
• 2010

Recently, reducing usage of cement and using by-product of industry such as blast furnace slag and fly-ash have been increased to reduce $CO_2$ gas emission. That apply to construction. As a result, reduction of environmental stress and recycling of resources are expected. In this study, as basic study to the reuse of resources and reduce Environmental Load, comparing and analyzing hardening characteristics and durability as using the blast furnace slag and fly-ash, examining concrete characteristics substituted the three elements for the blast furnace slag and fly-ash and evaluating the relationship as binder. Through this, it want to provide the basic data for mass utilization. Blast furnace slag powder and replaced at fly-ash compressive strength of concrete in the strength of the initial seven days material age lower level of expression significantly compared to the concrete, but, 28 days after the similar or higher compressive strength than the concrete expression of the was. In addition, the reserves replacement of blast furnace slag powder salt injury increasing resistance are seen improvements, according to the conventional blast furnace slag powder study by the chloride ions on the surface of the concrete are improved being fixation salt injury resistance is considered.

• Journal of Korean Society of Environmental Engineers
• /
• v.35 no.10
• /
• pp.710-716
• /
• 2013

New and renewable energy sources have drawn attention because of climate change. Many studies have been carried out in waste-to-energy field. Fast pyrolysis of waste lignocelluosic biomass is one of the waste-to-energy technologies. Bubbling fluidized bed (BFB) reactor is widely used for fast pyrolysis of the biomass. In BFB pyrolyzer, bubble behavior influences on the chemical reaction. Accordingly, in the present study, hydrodynamic characteristics and fast pyrolysis reaction of waste lignocellulosic biomass occurring in a BFB pyrolyzer are scrutinized. The computational fluid dynamics (CFD) simulation of the fast pyrolysis reactor is carried out by using Eulerian-Granular approach. And two-stage semi-global kinetics is applied for modeling the fast pyrolysis reaction of waste lignocellulosic biomass. To summarize, generation and ascendant motion of bubbles in the bed affect particle behavior. Thus biomass particles are well mixed with hot sand and consequent rapid heat transfer occurs from sand to biomass particles. As a result, primary reaction is observed throughout the bed. And reaction rate of tar formation is the highest. Consequently, tar accounts for 66wt.% of the product gas. However, secondary reaction occurs mostly in the freeboard. Therefore, it is considered that bubble behavior and particle motions hardly influences on the secondary reaction.

• Economic and Environmental Geology
• /
• v.47 no.6
• /
• pp.625-633
• /
• 2014

The Aquistore project is the world's first commercial capture, transportation, utilization and storage project of post-combustion $CO_2$ from a coal-fired thermo electric power plant, and the proposed storage is a saline aquifer at a depth of about 3,500 m. Deep saline aquifer, compared to hydrocarbon reservoir, provides the great volumetric potential for storage of $CO_2$ anywhere in the world, therefore the research results from the project may be exported globally to other sites. Geological $CO_2$ storage characterization for saline aquifer instead of hydrocarbon reservoir needs to estimate the geophysical properties of subsurface geology. This study calculated the geophysical property of water-saturated formation by applying amplitude variation analysis developed from oil and gas exploration. We correlated horizon tops at the well logs to seismic traveltime of 1,815 and 1,857 ms as Winnipeg and Deadwood formations. Gradient analysis from seismic traces showed correlation coefficient of 45 - 81 % on amplitude variation with respect to incident angle. Crossplot of intercept and gradient shows the inverse proportional trend which represents typical water saturated sediments. Product attribute of intercept and gradient described the base of wet sediment. Poisson's ratio change attribute increased at the top of target area satisfying with wet sediment and decreased at the top of basement in a dry rock bed.

• Korean Journal of Organic Agriculture
• /
• v.22 no.3
• /
• pp.491-502
• /
• 2014

The present study was conducted to investigate effective starter culture to improve biological activity of Asarum sieboldii. Antibacterial activity, antioxidant activity and reduction of enteric rumen methane production were used as criterions for biological activity. Ground A. sieboldii was added in MRS broth at 10% (w/v) and fermented by different starter cultures. Weissella confusa NJ28, Weissella cibaria NJ33, Lactobacillus curvatus NJ40, Lactobacillus brevis NJ42, Lactobacillus plantarum NJ45 and Lactobacillus sakei NJ48 were used for starter culture strains. Each starter culture was inoculated with 1% (v/v) ratio and fermentation was performed at $30^{\circ}C$ with agitation (150 rpm) for 48 h. MRS broth for the control was employed without starter culture. Then the fermentation growth was dried and extracted using ethyl alcohol. The growth of starter culture was detected at NJ40, NJ42, NJ45 and NJ48. And the highest cell growth was found in NJ40. Antibacterial activity against to Staphylococcus aureus, Listeria monocytogens, Mannheimia haemolytica and Salmonella gallinarum were observed in the extract fermented by NJ40 and NJ45. All treatments showed antioxidant activities, however, there were no significant differences (p>0.05). In in vitro rumen fermentation, negative control (NC) and positive control (PC) were assigned to without extract and with non-fermented A. sieboldii extract. Significant suppression of gas productions were detected in positive control and treatments compared to negative control (p<0.05). However, total volatile fatty acid production was not suppressed. Significant methane reduction per total volatile fatty acid productions were found in positive control and NJ45 treatment (p<0.05). The present study suggested a fermentation of A. sieboldii using NJ45 strain could improve its biological activity and make possible for its use in bio additive for enteric rumen methane mitigation without suppression of animal productivity.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.11 no.3
• /
• pp.219-228
• /
• 2001

Objective : For the purpose of preparing the fundamental data and health promotion and control program on organic solvents in air of manufacturing industry. Methods : The author surveyed number of organic solvent components which was used in working site and also determined the organic solvents concentration in air of 927 manufacturing industries and 1,267 working process with gas chromatography(NIOSH manual) for five years from 1995 to 1999. Results : Mean number of solvents components by type of industry, working process was number of 12. There were exceeded to TLV of 1,2-dichloroethane in textile manufacturing industry N,N-dimethyl furan in tanning and dressing of leather ; luggage, handbags, saddlery, harness and footwear manufacturing industry and chemical and chemical product manufacturing industry by type of industry. There were exceeded to TLV of 1,2-dichloroethane in handwriting and drawing process, cellosolve in adhesive spreading process, N,N-dimethly furan in production of solvent process and adhesion process by working process Total exceeded rate to threshold limit values of organic solvents mixture were 12.9% for EI(Exposure index) and 10.0% for Em(Estimation of mixture) by type of industry, 11.3% for EI and 8.2% for Em by type of working process. The highest exceed rate was 36.7% for EI in tanning and dressing of leather ; luggage handbags, saddlery, harness and footwear manufacturing industry and 29.0% for Em in textile manufacturing industry. The highest exceeded rate was 23.1% for EI and 12.5% for Em in adhesive spreading process by working process. Mean values of total subjects by type of industry and type of working process were $0.7{\pm}1.8$ for EI and $0.7{\pm}1.7$ for Em respectively. Conclusions : As above results, the author suggest that it makes the environmental control program on 1.2-dichloroethane, N,N-dimethyl furan, cellosolve by kind of organic solvent and on textile manufacturing industry, tanning and dressing of leather ; luggage, handbags, saddlery harness and footwear manufacturing industry by type of industry, and on handwriting, drawing process and adhesive spreading process and adhesion process by type of working process.