• Journal of Adhesion and Interface
• /
• v.4 no.4
• /
• pp.7-14
• /
• 2003

"Tack" is defined as "the property that enables an adhesive to form a bond with the surface of another material upon brief contact under light pressure". The tack depends on a number of experimental parameters. We can control various experimental factors (contact force, dwell time, pretest speed) using probe tack tester. We are here concerned with pretest speed of experimental factors using SIS-based hotmelt PSA and water-borne acrylic PSA.

• Journal of Adhesion and Interface
• /
• v.14 no.4
• /
• pp.167-174
• /
• 2013

In this study, Ultraviolet (UV) curable urethane acrylates for ink binder was prepared by reaction of IPDI, polyether polyol and HEA. The UV curing behavior of compositions with HEA/PETA ratio on UV irradiation time was investigated by FT-IR spectrophotometer, probe tack tester and Photo-DSC. Conversion % and gel content were increased with increasing UV irradiation time, but probe tack was decreased. Storage modulus, tensile strength and decomposition temperature were increased as PETA content increased. In case of HEA/PETA ratio was 30/70, adhesion property of UV-cured composition on PMMA sheet was excellent.

• Journal of Adhesion and Interface
• /
• v.14 no.3
• /
• pp.117-120
• /
• 2013

The prepreg material is a sheet of the reinforcement pre-impregnated with a resin. In this study, two types of prepreg were prepared with a general phenolic resin and the polyvinyl butyral (PVB) modified phenolic resin, respectively, with resin content of 40 wt%. After resin impregnation, the prepregs were heat treated in an oven to make them the B-stage. Surface morphology of the prepreg was observed by using a scanning electron microscope (SEM). Tack property of the prepreg is one of the major properties that govern the ability of prepreg to be laid up. In this study, the tack of prepreg was measured under various test parameters by a probe tact test. Test parameters were contact time, contact force and debonding rate. Most of the tack properties of the prepreg increased with the test parameters. Then tack properties exhibited a linear behavior with test parameters before a saturation point. Also, the tack of prepreg was investigated in relation with the fibrillation phenomena involved in the prepreg surface with the debonding rate.

• Journal of Adhesion and Interface
• /
• v.6 no.3
• /
• pp.19-25
• /
• 2005

Synthetic rubber based pressure-sensitive adhesives (PSAs) usually containing SIS or SBS block copolymer, tackifier, plasticizer, and other additives are now widely used on various applications. As these PSAs are physically crosslinked and can be applied without the use of solvent, they are thermally processable and environmentally friendly. However these PSAs cannot be used in high temperature applications and in applications where solvent and chemical resistance properties are required. We developed the PSA adding UV curable system, such as thiol-ene system, to increase adhesion properties at elevated temperature. The adhesion properties such as probe tack, peel strength, shear adhesion failure temperature (SAFT) were evaluated. The probe tack test was conducted with varying probe materials and coating thickness of PSAs. Using the contact angle, the surface property of the cured PSAs was also observed.

• Journal of Adhesion and Interface
• /
• v.8 no.2
• /
• pp.15-21
• /
• 2007

To prepare a natural rubber-based pressure-sensitive adhesive (PSA) for protection film of opto- functionalized sheet, natural rubber (NR) was blended with a DCPD type tackifier and three types of aliphatic hydrocarbon resins, respectively. Also, to supply low cohesion strength of NR, in the fixed ratio of tackifier, synthetic rubber, styrene-isoprene-styrene (SIS) block copolymer was blended with NR as a function of SIS contents. PSA performance of prepared PSAs was evaluated using probe tack and peel strength. Probe tack of NR/tackifier blends was increased with increasing tackifier contents, and showed maximum peak. In addition, probe tack of NR/tackifier blends slightly increased with increasing softening point of aliphatic hydrocarbon resins. Their peel strength increased up to 50 wt% of tackifier contents, but in the over contents of tackifier, they showed stick-slip failure mode. Finally, probe tack of NR/SIS/tackifier blends showed the maximum values at 20~40 wt% of tackifier contents, but at 20 wt% of tackifier contents, they showed fibrillation. For this reason, peel strength showed maximum values at 40 wt% of tackifier contents.

• Journal of Adhesion and Interface
• /
• v.9 no.3
• /
• pp.27-33
• /
• 2008

A series of aluminum acetylacetonate (AlACA) belonging in inorganic chelate calculating with the ratio of -COOH mole in PSA (0, 0.25, 0.5, 0.75, 1) and a series of PSA with different acrylic acid contents (3 wt%, 7 wt%, 10 wt%) were blended and measured gel contents, probe tack, peel strength, SAFT. With the increasing of aluminum acetylacetonate contents, the network structure was formed and gel contents were increased. Probe tack fibrillation and peel strength were decreased following the addition of aluminum acetylacetonate. SAFT were significantly changed with the change of acrylic acid contents in PSA. From these results, aluminum acetylacetonate could be used in the range of which would not change the performance a lot, and cure the PSA.

• Journal of Adhesion and Interface
• /
• v.12 no.2
• /
• pp.67-72
• /
• 2011

Acrylic pressure-sensitive adhesives are used in many different parts in the world. But acrylic acid in PSAs may occur unexpected results such as corroding adherends or producing by-products when applied within electronic devices. This study employed acrylic PSAs based on 2-ethylhexyl acrylate (2-EHA), 2-hydroxyethyl acrylate (2-HEA) and butyl acrylate (BA) with different coating thickness. There are two types of curing agents. One is methylaziridine derivative (MAZ) and the other is aluminum acetylacetonate (AlACA). This study examined the adhesion performance and curing behaviors using peel strength, probe tack and gel fraction. Also, the viscoelastic properties of acrylic PSAs were investigated from Advanced rheometric expansion system (ARES).

• Journal of Sensor Science and Technology
• /
• v.25 no.5
• /
• pp.344-348
• /
• 2016

We developed a 2-channel fiber-optic temperature sensor (FOTS) using a temperature sensing probe, a fiber-optic coupler, transmitting optical fiber, and an optical time domain reflectometer (OTDR). The temperature sensing probe is divided into a sensing probe and a reference probe for accurate thermometry. A sensing probe is composed of a silicon oil, a FC terminator, a brass pipe, and a singlemode optical fiber and the structure of a reference probe is identical with that of the sensing probe excluding a silicon oil. In this study, we measured the modified optical powers of the light signals reflected from the temperature sensing probe placed inside of the water with a thermal variation from 5 to $70^{\circ}C$. Although the optical power of the reference probe was constant regardless of the temperature change, the optical power of the sensing probe decreased linearly as the temperature increased. As experimental results, the FOTS using a subtraction method showed a small difference (i.e., hysteresis) in its response due to heating and cooling. The reversibility and reproducibility of the FOTS were also evaluated.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.20 no.4
• /
• pp.395-400
• /
• 2011

Scanning Probe Lithography is a method to localized oxidation on single crystal silicon wafer surface. This study demonstrates nanometer scale non contact lithography process on (100) silicon (p-type) wafer surface using AFM(Atomic force microscope) apparatuses and pulse controlling methods. AFM-based experimental apparatuses are connected the DC pulse generator that supplies ultra short pulses between conductive tip and single crystal silicon wafer surface maintaining constant humidity during processes. Then ultra short pulse durations are controlled according to various experimental conditions. Non contact lithography of using ultra short pulse induces electrochemical reaction between micro-scale tip and silicon wafer surface. Various growths of oxides can be created by ultra short pulse non contact lithography modification according to various pulse durations and applied constant humidity environment.

• Journal of Adhesion and Interface
• /
• v.10 no.3
• /
• pp.134-140
• /
• 2009

The acrylic copolymers with variation in side chain were synthesized based on molecular design. Wettability and adhesion properties on the wafer surface were investigated for these acrylic copolymer pressure sensitive adhesives. Three-dimensional networks of linear acrylic copolymers were produced with epoxy-type Tetra-DX cross-linking agent. The effect of cross-linking on adhesion characteristics was investigated. The side chain of acrylic copolymer played more important role in wettability than the interfacial interaction. As the degree of cross-linking increased, both probe tack and peel strength decreased. Also, heat resistance measured by SAFT increased with cross-linking; however, it showed the deterioration when excess cross-linking agent was added.