• 한국세라믹학회지
• /
• 제42권11호
• /
• pp.722-728
• /
• 2005

A wet-chemical route was utilized to obtain nanosized crystalline goethite ($\alpha$-FeOOH) particle, which was known as an oxidation catalyst in reducing carbon monoxide (CO) and dioxine during incineration. A cost-effective $FeSO_4{\cdot}7H_2O$ was used as starting raw material and a successive process of hydrolysis-oxidation was utilized as synthetic method. The effects of the initial $Fe^{2+}$ concentration, hydrolysis time and oxidation period on the crystalline phase and particle characteristics were systematically investigated by X-Ray Diffraction (XRD), Scanning Electron Microscopy (SEM) and BET analyses. It was found that the spindle-shaped crystalline $\alpha$-FeOOH particle with the width of 70 nm and the length of 200 nm could be obtained successfully when the initial concentration of 1.5 M, hydrolysis time of 4h, and oxidation period of 10 h, respectively. In addition, it was observed that the spindle-shaped $\alpha$-FeOOH particle consisted of nano-sized primary crystallites of $30\~50\;nm$, which were de-agglomerated into individual particle and successively re­agglomerated into spherical or irregular-shaped agglomerates beyond certain periods in the hydrolysis and oxidation process.

• 한국분말재료학회지
• /
• 제25권5호
• /
• pp.408-414
• /
• 2018

This study investigates the microstructure and wear properties of cermet (ceramic + metal) coating materials manufactured using high velocity oxygen fuel (HVOF) process. Three types of HVOF coating layers are formed by depositing WC-12Co, WC-20Cr-7Ni, and Cr3C2-20NiCr (wt.%) powders on S45C steel substrate. The porosities of the coating layers are $1{\pm}0.5%$ for all three specimens. Microstructural analysis confirms the formation of second carbide phases of $W_2C$, $Co_6W_6C$, and $Cr_7C_3$ owing to decarburizing of WC phases on WC-based coating layers. In the case of WC-12Co coating, which has a high ratio of $W_2C$ phase with high brittleness, the interface property between the carbide and the metal binder slightly decreases. In the $Cr_3C_2-20CrNi$ coating layer, decarburizing almost does not occur, but fine cavities exist between the splats. The wear loss occurs in the descending order of $Cr_3C_2-20NiCr$, WC-12Co, and WC-20Cr-7Ni, where WC-20Cr-7Ni achieves the highest wear resistance property. It can be inferred that the ratio of the carbide and the binding properties between carbide-binder and binder-binder in a cermet coating material manufactured with HVOF as the primary factors determine the wear properties of the cermet coating material.

• 한국동물위생학회지
• /
• 제34권4호
• /
• pp.429-439
• /
• 2011

This article described the comparison of a quick, easy, cheap, effective, rugged and safe (QuEChERS) sample preparation and the classical method established by National Veterinary Research and Quarantine Service (NVRQS) for the determination of pesticide residues in livestock products using GC-tandem mass spectrometry. The classical method by NVRQS used liquid-liquid partioning followed by evaporizing. The modified QuEChERS entailed extraction of 2 g sample with 15 ml acetonitrile containing 1% acetic acid followed by addition of 6 g anhydrous magnesium sulfate and 1.5 g sodium acetate. After centrifugation, 6 ml of the extract underwent a cleanup step (in a technique known as column-based solid phase extraction) using 400 mg each of $C_{18}$ and primary secondary amine sorbents plus 1,200 mg magnesium sulfate. The quantitation of individual pesticides by both methods was based on tissue standard calibration curves with a correlation coefficient in excess of 0.98 for the 24 pesticides. The detection limits by the classical method were ranged 1.3~5.0 ${\mu}g$/kg, with mean recoveries between 76.2% and 114.3% except aldrin (59.3%) and deltamethrin (63.6%). The detection limits by modified QuEChERS were ranged 0.3~6.2 ${\mu}g$/kg, with mean recoveries between 68.0% and 114.3% except dimethipin (152.6%), chlorfenvinphos (138.1%), 4,4-DDT (61.5%), aldrin (60.4%) and chinomethionate (30.3%).

• 한국세라믹학회지
• /
• 제43권10호
• /
• pp.666-672
• /
• 2006

GDC20($Ce_{0.8}Gd_{0.2}O_{1.9}$) powder was synthesized by oxalate co-precipitation and milling and its thermal decomposition, phase formation, and sinterability were investigated. As-prepared precipitates were non-crystalline due to the milling process and completely decomposed at 400$^{\circ}C$ The powder calcined at 800$^{\circ}C$ for 2 h contained fine p]sty particles with an average size of 0.69 $\mu$m. Attrition milling of the calcined powder for 2 h had a little milling effect, resulting in a slight decrease in the particle size to 0.45 $\mu$m. The milled powder consisted of small spherical primary particles and some large particles, which had been agglomerated during calcination. Due to the excellent sinterability of the powder, sintering of the powder compacts for 4 h showed relative densities of 78.7% at 1000$^{\circ}C$ and 97.8% at 1300$^{\circ}C$, respectively. Densification was found to almost complete at temperature above 1200$^{\circ}C$ and a dense and homogeneous microstructure was obtained. A rapid grain growth occurred between 1200$^{\circ}C$ and 1300$^{\circ}C$. Grains in 0.1$\sim$0.5 $\mu$m sizes at 1200$^{\circ}C$ grew to 0.2$\sim$2 $\mu$m and their size distribution became broader at 1300$^{\circ}C$.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 하계학술대회 논문집 C
• /
• pp.2098-2100
• /
• 2000

We propose pulsed $CO_2$ laser below 30W by the AC(60Hz) switching control of leakage transformer primary which has some advantage of cost and size compared to a typical pulsed power supply. Pulse repetition rate is adjusted from 5Hz to 60Hz to control laser output. In this laser, a low voltage open loop control for high voltage discharge circuit is employed to avoid the HV sampling or switching and high voltage leakage transformer is used to convert rectified low voltage pulse to high voltage one. A ZCS(Zero Cross Switch) circuit and a PIC one-chip microprocessor are used to control gate signal of SCR precisely. The pulse repetition rate is limited by 60Hz due to the frequency of AC line and a high leakage inductance. The maximum laser output was obtained about 23W at pulse repetition rate of 60Hz, total gas mixture of $CO_{2}/N_{2}$/He = 1/9/15, SCR gate trigger angle 90$^{\circ}$, and total pressure of 18Torr.

• 한국자기학회지
• /
• 제2권2호
• /
• pp.91-98
• /
• 1992

$Co_{67}Fe_{4.5}Nb_{2}Si_{10}B_{15}$ 비정질합금리본에서 2단 어닐링이 자기특성에 미치는 영향을 조사 하였다. 고온인 $480^{\circ}C$ 이상에서 20분간 1단 어닐링한 리본을 저온인 $310^{\circ}C$에서 2시간 동안 2단으로 진공어닐링한 결과 보자력과 각형비는 1단 어닐링한 경우와 거의 비슷한 값들을 나타내었으나, 직류 및 교류투자율은 1단 어닐링에 비해 현저히 높아졌다. 2단 어닐링시 직류 및 1 kHz에서의 교류투자율의 최대치는 각각 약 290,000과 41,000으로서 1단 어닐링에 비해 30% 이상 증가하였다. 어닐링온도에 따른 자성의 변화는 3단계로 나누어 내부응력, 자구크기, cluster 및 결정상의 변화를 주요 요인으로 하여 고찰하였다.

• 한국전산구조공학회논문집
• /
• 제27권4호
• /
• pp.265-271
• /
• 2014

304L 스테인리스강판은 멤브레인타입 LNG선 단열시스템의 1차 방벽으로 이용된다. 304L 스테인리스강은 변태유기소성(TRIP)강으로 복잡한 재료거동을 보이는데, 이는 소성변형이 발생하는 동안 상변태를 경험하기 때문이다. 본 연구에서는 304L 스테인리스 강의 비선형 기계적 거동분석을 위한 온도의존 일축인장시험을 수행하였으며 재료의 파단이나 비선형 거동을 예측하기 위한 점소성모델을 제안하였다. 수치해석의 결과와 시험 결과를 비교 분석하여 유효성을 검증하였으며 LNG 멤브레인에 대한 적용성을 검토하기 멤브레인 구조시편을 제작하여 구조해석 및 유한요소해석을 수행하였다. 재료모델은 개발 서브루틴을 이용하였으며 ABAQUS 사용자지정 재료 서브루틴을 탑재한 유한요소해석 결과와 극저온 구조인장시험을 수행한 결과를 비교하여 구조적용성을 검증하였다.

• 한국동물학회지
• /
• 제32권2호
• /
• pp.153-162
• /
• 1989

난자성숙 재개와 1-세포기 배아의 세포주기에서, cAMP-의존성 protein kinase A와 diacylglycerol-의존성 protein kinase C가 핵막붕괴에 미치는 영향을 조사하였다. 난자성숙 재기는 dbcAMP, IBMX, TPA, 또는 diacyllycerol에 의해 억제되었다. 또한 protein kinase A와 protein kinase C 활성제를 같이 처리하면 난자성숙이 더욱 억제되었다. 그러나 1-세포기 배아의 전핵막붕괴에는 아무런 영향도 미치지 못하였으며, 단지 protein kinase C 활성제만이 세포질 분열을 억제하였다. 이상의 결과로부터, protein kinase A와 protein kinase C에 의한 단백질 인산화 양상이 GV난자의 핵막붕괴와 1-세포기 배아의 전핵막붕괴에 미치는 세포내 작용기작은 상이함을 알 수 있었으며, 전기영동 결과, 81 KD 단백질이 난자성숙 재개에 중요한 역할을 하리라 사료되었다.

• 한국수학교육학회지시리즈C:초등수학교육
• /
• 제18권2호
• /
• pp.77-89
• /
• 2015

영재지도에 대한 지속적인 관심 속에서 '독립연구'가 영재학생들의 학습 양식에 부합하는 교육의 한 가지 형태로 주목을 받고 있다. 이에 본 연구에서는 초등수학 영재학생들의 '독립연구를 위한 점검표'를 개발하고, 이를 적용하여 학생들의 독립연구 산출물에 나타난 특징을 분석하였다. 독립연구 산출물에 나타난 특징을 분석한 결과, 첫째, '독립연구를 위한 점검표'가 학생 스스로 자신의 독립연구 과정을 확인할 수 있는 자기점검 체크리스트로서 역할을 하였다. 둘째, '독립연구를 위한 점검표'의 점검 내용은 영재학생들에게 토론 주제를 제시하여 풍부한 토론을 유도하였다. 셋째, '독립연구를 위한 점검표'는 영재 독립연구 지도교사에게 학생들의 특성에 부합하는 지도 자료로 활용될 수 있었다. 넷째, 학생의 연구주제 및 연구방법에 따라 '독립연구를 위한 점검표'는 선택적으로 활용될 수 있었다.

• Molecules and Cells
• /
• 제40권8호
• /
• pp.587-597
• /
• 2017

MicroRNAs (miRNAs) are essential small RNA molecules that regulate the expression of target mRNAs in plants and animals. Here, we aimed to identify miRNAs and their putative targets in Hibiscus syriacus, the national flower of South Korea. We employed high-throughput sequencing of small RNAs obtained from four different tissues (i.e., leaf, root, flower, and ovary) and identified 33 conserved and 30 novel miRNA families, many of which showed differential tissuespecific expressions. In addition, we computationally predicted novel targets of miRNAs and validated some of them using 5' rapid amplification of cDNA ends analysis. One of the validated novel targets of miR477 was a terpene synthase, the primary gene involved in the formation of disease-resistant terpene metabolites such as sterols and phytoalexins. In addition, a predicted target of conserved miRNAs, miR396, is SHORT VEGETATIVE PHASE, which is involved in flower initiation and is duplicated in H. syriacus. Collectively, this study provides the first reliable draft of the H. syriacus miRNA transcriptome that should constitute a basis for understanding the biological roles of miRNAs in H. syriacus.