• 한국연소학회지
• /
• 제21권4호
• /
• pp.16-22
• /
• 2016

Pressure and temperature variations in a shock tube have been studied numerically by changing the diameter ratio of a driven part to a driver part. There are five cases where the adopted diameter ratios are 40%, 50%, 60%, 80%, and 100% respectively. The diameter of the driver part remains unchanged meanwhile the shock tube driven part diameter increases from 40% to 100% of the driver part. In the 100% ratio case, the driver part and driven parts have the same diameter of 66.9 mm. As the diameter ratio decreases, the pressure in the shock tube and available test time are increased.

• 한국공간구조학회논문집
• /
• 제2권1호
• /
• pp.67-73
• /
• 2002

Measurement of fluctuating pressure by tube system is carefully designed due to the organ-pipe resonance. It is necessary to correct the pressure before analysis. The three method for correction the distortion fluctuation pressure short tube length and the frequency response functions and insert a restrictor in the tube to increase the damping. The first method is useful when the tube length is short. In second method, the distorted signal through the tubing transformed into the frequency domain, dividing by transfer function and inverse fourier transforming back into the time domain gives the required pressure signal. In this paper three types of tubing which have different length of 100cm, 150cm, 200cm were experimented the distorted signal and correct the distortion signal

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2010년도 춘계학술대회 논문집
• /
• pp.139-150
• /
• 2010

최근 한국에서는 세계적인 녹색기술을 맞아 향후 차세대 교통 시스템으로서 튜브 트레인 시스템의 본격적인 연구가 진행되고 있다. 한국 철도기술연구원(KRRI, Korea Railroad Research Institute)에서 튜브 트레인 시스템의 건설을 위한 목적으로 연구가 진행되고 있다. 본 논문에서는 기초연구의 일환으로 축대칭하며 긴 형상의 수송체가 가지는 다양한 튜브(터널) 내부의 압력, 막힘비율, 운행속도를 파라미터로 선정하여 전산해석을 수행하였다. 세부사항으로는 동일 형상의 운송체가 동일 운행속도를 가지고 일반적 압력의 개활지(오픈 시스템, 개활지 운행)를 운행할 때와, 다양한 환경(튜브 내 압력, 막힘비율, 운행속도)의 튜브 내부를 운행할 때에 대하여 튜브 트레인의 공력특성 연구를 수행하였다. 이를 통하여 다양한 운행속도-막힘비율 별로 개활지와 동일 에너지 효율 나오는 튜브 내 압력(P-D 관계)을 계산하였고, 막힘비율 증가에 따른 튜브 내 감압 정도(P-${\beta}$ 관계), 다양한 막힘비율-튜브 내 압력 별로 운행속도에 따른 전체 항력 양상(D-V 관계)을 보여 주었다. 그리고 개활지 운행시와 튜브 내부 운행시의 에너지 효율(주행저항)을 비교하였고, 튜브 내부 운행 시 트레인이 갖는 효율과 관계되는 충격파 발생의 임계속도(critical V-B 관계) 및 한계속도(V-P 관계)를 얻을 수 있었다. 이러한 연구의 결과는 튜브 시스템 설계 및 건설에 꼭 필요한 것이며 가이드라인을 제시했다.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2006년도 하계학술발표대회 논문집
• /
• pp.657-662
• /
• 2006

The present paper dealt with an experimental study of condensation heat transfer coefficients with refrigerant R-22, R-407C and R-410A, and was focused on pressure gradient and heat transfer coefficient in horizontal tube-in-tube heat exchangers using inner diameter of 4 mm, 3 mm and 2 mm in a 16.91 mm tube and length of 3,000 mm. Experiments were performed at inlet saturation temperature of 35 to $45^{\circ}C$ and mass flux ranges from 200 to $600 kg/m^2s$. The pressure gradient with inner tube diameter of 4.0 mm is higher 2.5 times than that of 8.0 mm. In tube-in-tube HEX, the pressure gradient of R-410A were lower than those of R-22 and R-407C. The condensation heat transfer coefficients increased with mass flux increase, but they decreased with saturation temperature increased. Condensation heat transfer coefficients of R-410A were a little higher than those of R-22 and R-407C. The condensation heat transfer coefficients of tube-in-tube HEX were about 40% higher than those of double tube HEX.

• 대한기계학회논문집
• /
• 제16권6호
• /
• pp.1056-1063
• /
• 1992

본 연구에서는 평면변형이론을 적용하여, 진원형 튜브의 경우 주로 Durban의 과정에 따르고, 몇 가지의 타원형 모델들에 대하여 상용 유한 요소프로그램인 Solvia 를 이용하여 각기 해석하고, 파열압력에 대한 예측값을 구하였으며 각기 해석하고, 파열압력에 대한 예측값을 구하였으며 결함의 영향을 파악하였다.또 반경 대 두께 비가 다른 2가지 시편에 대한 파열시험을 수행하여 해석결과와 비교하였다.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2005년도 후기학술대회논문집
• /
• pp.244-245
• /
• 2005

This paper presents the heat transfer and pressure drop characteristics during cooling process of carbon dioxide in a horizontal tube. The test section is a tube in tube type heat exchanger with refrigerant flowing in the inner tube and water flowing in the annulus. It was made of a stainless steel tube with the inner diameter of 7.75 [mm], the outer 2 diameter of 9.53 [mm] and length of 6000 [mm]. The refrigerant mass fluxes were $200{\sim}400$ [kg/$m^2s$] and the average pressure varied from 7.5 [MPa] to 10.0 [MPa]. The main results were summarized as follows The heat transfer coefficient of supercritical $CO_2$ increases in decrease of the gas cooler pressure. And the heat transfer coefficient increases with respect to the increase of the refrigerant mass flux. Among some correlations proposed in a transcritical region, Bringer-Smith's correlation has some analogy with experimental results. The pressure drop decreases in increase of the gas cooler pressure and increases with respect to increase the refrigerant mass flux.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2008년도 제30회 춘계학술대회논문집
• /
• pp.53-56
• /
• 2008

일반적으로, 고체로켓모타에 대한 지상연소시험을 실시할 경우, 연소관 내부의 압력을 계측하기 위해 압력 계측용 배관에 기름을 채우고 그 끝에 압력센서를 연결하여 사용한다. 통상적으로 사용되어지는 이 방법은 지상연소시험을 실시할 경우에는 특별한 문제가 되지 않으나, 고고도 환경에서 점화되는 고체로켓모타의 압력계측은 배관 기름의 누출로 인한 점화성능 저하가 문제시된다. 이는 배관의 부착 위치가 통상적으로 전방 점화기 부위인 것에 기인한 것이며, 이러한 문제를 해결하기 위하여 본 논문에서는 기름을 사용하지 않는 압력배관을 어떻게 설계하고 검증하였는지에 대해 기술하도록 하겠다.

• 설비공학논문집
• /
• 제13권11호
• /
• pp.1149-1155
• /
• 2001

The experimental investigation on energy separation in a vortex tube has been carried out to sow the effect of inlet and outlet pressures with various working fluids(air,$O_2,\;and\; CO_2$). Those outlet pressure means cold outlet and hot outlet pressure which were set equally. The results showed that the total enthalpy variation became a maximum when the mass flow rate at the cold outlet was a half of the total mass flow rate in the vortex tube (y=0.5). The total enthalpy variation was quite affected by the pressure difference between the inlet and outlet of vortex tube when the ratio of the inlet pressure to the cold outlet pressure remained constant. Although specific enthalpy differences between the inlet and the outlet (both cold and hot outlet) did not noticeably vary with the pressure difference, the specific enthalpy difference between the inlet and cold outlet was dominantly affected by physical properties of working gases.

• 오토저널
• /
• 제13권3호
• /
• pp.32-42
• /
• 1991

In SI engine research the pressure data in cylinder is the most important fundamental ones leading to engine efficiencies and performances. It is, therefore, necessary to obtain accurate pressure data and yet it is often impossible to install a reliable data producing, flush-mounted type pressure transducer in a cylinder of small and medium size multicylinder SI engines. When flush mounting the transducer is not possible, the spark-plug type pressure transducer is commonly used as an alternative. In this case, the transmission tube of spark-plug type pressure transducer introduces distortions in the pressure signal. Efforts were made to understand the dynamic characteristics of spark-plug pressure transducer by shock tube tests and real engine experiments. In engine experiment the cylinder pressure data were simultaneously obtained by both flush mounted and spark-plug type pressure transducers of certain transmission tube geometry. Those pressure data collected by spark-plug type pressure transducer were tested for correction to flush mounted ones by the application of transfer function. As a result of the calibration the IMEP difference between F/M data and improved S/P data was shown to be corrected about 75-98% from the original ones.

• 한국농공학회논문집
• /
• 제51권5호
• /
• pp.19-24
• /
• 2009

This study was conducted to provide fundamental data for design of air inflating apparatus of air-inflated double-layer plastic greenhouse. The variation of static pressure in air tube for different fans and filters, filtering performance for various kinds of filters and destruction phase of experimental greenhouse collapsed by excessive static pressure in air space were analyzed. The general type of forward centrifugal fan was recommended for inflating air space in air-inflated double-layer plastic greenhouse. The experimental greenhouse was collapsed down by excessive static pressure just like fallen by heavy snow load acting on it. The static pressure in air tube without filter decreased linearly as the number of outlet openings increased. But the pressure in air tube with filter declined quadratically, the decremental ratio diminished by the increase of outlet openings. The higher filtering efficiency and the greater decrements of static pressure in air tube, the larger capacity fan was required for maintaining proper static pressure in air space. Because the porosities of filter were blocked by dust as time goes by, the static pressure in air tube with filter decreased. The higher filtering efficiency, the less decremental ratio of static pressure in air tube as time passes by. Considering the filtering efficiency, decrement of static pressure and thickness of filter, the 5mm thickness filter of 75% efficiency was recommended for air inflating filter of air-inflated double-layer plastic greenhouse.