• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 1999.11a
• /
• pp.71-75
• /
• 1999

This paper describes the temperature characteristics and influence produced from the unification of Magnetic Ballast and simple Electronic starter for fluorescent lamp. This is affected by the transmitted Temperature from a part of Ballast loss in half-wave rectifier electronic starter. The simulation and experiment show that characteristics of capacitor in electronic starter is changed by the high temperature(80$^{\circ}C$) of magnetic ballast, and preheating time of lamp is reduced by it.

• 한국연소학회:학술대회논문집
• /
• 2002.11a
• /
• pp.65-69
• /
• 2002

Catalytic combustion known as one of the traditional oxidation methods of VOC gas is restricted to its applicable fields because of its reaction characteristics. But recently innovative improvement of catalytic endurance makes its applicable range broader from MEMs to industrial power generation. Therefore, control technologies based on the catalytic combustion characteristics are researched and developed dynamically. Especially, the stable control of catalytic combustion is an essential factor in a view of maximizing its efficiency. In this research, the fuel equivalence ratio and the preheating temperature of mixture gas is controlled by catalytic combustion system enhanced in heat transfer with high temperature heat exchanger. As a result, the combustion characteristics of system was investigated, and both passive and active control type were compared and analyzed.

• 한국연소학회:학술대회논문집
• /
• 2006.04a
• /
• pp.13-18
• /
• 2006

Radiant burners are applicable to drying, preheating and curing in materials manufacturing processes. High radiation efficiency is one of the most important performance criteria for these burners. The wide variation in reported radiation efficiencies are partly due to the differences in the measurement techniques. In the present work, water cooled radiant heat flux meter was used to measure radiant heat flux from a metal fiber mat burner. Non-contact type thermometer was also utilized to measure the surface temperature of the burner. Combustion gas was measured by gas analyzers. According to the thermal loads and stoichiometric ratios, radiant heat transfer ratio and combustion performance were discussed here in.

• Proceedings of the KWS Conference
• /
• 2003.05a
• /
• pp.32-33
• /
• 2003

The evaluation of HAZ toughness and cold crack susceptibility of 90mm thickness API 2W Grade 50 steel has been made in accordance with API RP 2Z as preproduction qualification test to be certified as il steel supplier from Shell International E & P. It was shown that the steel has superior HAZ toughness; CTOD value for CGHAZ more than 1.5mm at -10$^{\circ}C$, CVN absorbed energy more than 150J at -60$^{\circ}C$. Additionally, no generation of cold cracks was observed at 0.7kJ/mm even without preheating condition. These excellent results are due to the extremely low hardenability in HAZ of the steel.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.13 no.1
• /
• pp.60-67
• /
• 2005

Mild combustion or Flameless oxidation(FLOX) have been considered as one of the most prospective clean-combustion technologies to meet both the targets of high process efficiency and low pollutant emissions. A mild combustor with high air preheating and strong internal exhaust gas recirculation is characterized by relatively low flame temperature, low NOx emissions, no visible flame and no sound. In this study, the Steady Flamelet Approach has been applied to numerically analyze the combustion processes and NOx formation in the mild combustor. The detailed discussion has been made f3r the basic characteristics of mild combustor, numerical results and limitation of the present combustion modeling.

• Proceedings of the Korean Society of Laser Processing Conference
• /
• 2001.05a
• /
• pp.31-34
• /
• 2001

Laser cladding Processing allows rapid transfer of heat to the material being minimum conduction into base metal. The effects of CO$_2$ laser cladding with high powder were investigated. High viscosity bronze powder consists of bronze powder used at a high temperature. The material has a high viscosity So that it can be substrate. Therefore. Laser cladding can be processed on a curved or slope surface. CO$_2$ laser cladding was designed It consists of the high viscosity bronze powder the shielding gas system and the preheating system The high viscosity powder properly at 0.3g/s and 0.50g/s. Because of the metallic bond between bronze per the hardness of dilution layer was suddenly increased. Experimental as results viscosity mixed powder can be a useful cladding material.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2003.05a
• /
• pp.89-94
• /
• 2003

Recently, the study to reduce and recycle industrial waste is underway vigorously in the various fields of industry according to the conservation of environment and resources. In construction work, the disposal problem of its waste and environmental disruption have already been serious all over the world. However the recycle of waste concrete is still at an early stage, recycled aggregate from waste concrete have only used those as subsidiary road fillers. The research institute and the company make the study that it is about the properties of recycled aggregate and those structural capacity since 1990. Through the experimentation last year, we know that strength and fluidity of recycle cement are inferior to normal cement, and admixing aggregate powder deteriorates its strength. The purpose of this study is to search for appropriate heating time and to improve performance of the recycle cement while heating hardened cement which is crushed, we investigate separating aggregate from hardened cement by preheating and improvement of strength and fluidity inrecycle cement which contains admixture.

• Proceedings of the KIEE Conference
• /
• 1998.07f
• /
• pp.2088-2090
• /
• 1998

A low-cost electronic starter is developed to decrease ignition failure significantly through successive starting trial and to prevent overheating at the end of fluorescent lamp life. Moreover, it has an additional feature of being capable of ignition at the recovered lamp voltage without any circuit correction. The developed electronic starter is consisted of four parts - a half wave rectifier circuit, a timer circuit, a switching circuit and a protection circuit. The protection circuit made up of a transistor and capacitors utilizing capacitive characteristics, carries out successive starting trial and end-of-life protection. Lamp ignition is completed within 0.5 seconds with taking advantage of a high preheating current from the half-wave rectifier circuit. Nevertheless, its performance is proved to be very excellent through a standard switching endurance test.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.04a
• /
• pp.79-82
• /
• 2002

Induction heating is widely used in today's industry, in operations such as metal hardening, preheating for forging operations, melting or cooking. In this paper, it was presented the magneto-thermal analysis of an induction heating jar(IH-JAR) with the material value of the stainless and the aluminum for efficient design. The magnetic field intensity inside the axisymmetric shaped cooker was analyzed using three-dimensional axisymmetric finite element method(FEM) and the effectual heat source was obtained by ohmic losses from eddy currents induced in the jar. The heat was calculated using the heat source and heating equation. Also, it was represented the temperature characteristics of the IH-JAR according to time and relative permeability in stainless parts and in aluminum parts.

• Journal of Ship and Ocean Technology
• /
• v.8 no.4
• /
• pp.34-44
• /
• 2004

Engine visualization is the most important process to develop the new engine. But this step has a major difficulty that is almost impossible to access the engine on running. Therefore, little indication from the experimental and analytical results has been so far. This work has conducted the important issue of developing a quartz liner. And it has given us good qualitative and quantitative results of temperature and stress fields in the quartz cylinder by considering forced convection of outside quartz liner, thickness of the quartz liner and preheating effect to operate quartz engine safely.