• Journal of Astronomy and Space Sciences
• /
• v.20 no.4
• /
• pp.339-350
• /
• 2003

Engineering qualification model payload for a communications and broadcasting satellite(CBS) was developed by ETRI from May, 2000 to April, 2003. For. the purpose of functional test and verification of the payload, a real-time hardware-in-the-loop(HITL) CBS simulator(CBSSIM) was also developed. We assumed that the spacecraft platform for the CBSSIM is a geostationary communication satellite using momentum bias three-axis stabilization control technique based on Koreasat. The payload hardware is combined with CBSSIM via Power, Command and Telemetry System(PCTS) of Electrical Ground Support Equipment(EGSE). CBSSIM is connected with PCTS by TCP/IP and the payload is combined with PCTS by MIL-STD-1553B protocol and DC harness. This simulator runs under the PC-based simulation environment with Windows 2000 operating system. The satellite commands from the operators are transferred to the payload or bus subsystem models through the real-time process block in the simulator. Design requirements of the CBSSIM are to operate in real-time and generate telemetry. CBSSIM provides various graphic monitoring interfaces and control functions and supports both pre-launch and after-launch of a communication satellite system. In this paper, the HITL simulator system including CBSSIM, communications payload and PCTS as the medium of interface between CBSSIM and communications payload will be described in aspects of the system architecture, spacecraft models, and simulator operation environment.

• Journal of Astronomy and Space Sciences
• /
• v.13 no.2
• /
• pp.173-180
• /
• 1996

This paper briefly describes the KITSAT-1 and KITSAT-2 spacecrafts and presents the functions, calibration procedures and in-orbit results of the KITSAT-2 analog sun sensors have been flown as an experimental payload for the future mission. We have two constraints in their design: small size and very low power consumption due to the tight mass and power budget of the spacecraft. Two one-dimensional analog sun sensors are mounted on the top facet of the KITSAT-2 spaceraft. Each has $\pm$60 degrees of view angle and they cover 210 degree field of view in total as the 30 degree view angles are overlapped. Only the relative sun angle around the Z-axis (yaw-axis) and the spin rate of the spacecraft can be achieved as the one dimensional sun sensors are used and they are aligned with the Z-axis. The calibration formulae are obtained using the fifth order line fitting algorithm for each sun sensor on the ground and they are applied to the obtained in-orbit data. ASS-1 with silicon solar cells has maximum error of 1.5 degree and ASS-2 with silicon photocells manufactured at KAIST has maximum error of 0.5 degree except near 0 degree of sun ray incident anagle where random reflection of incident sun ray is maximum in orbit. The results are presented in chapter 4. The performance of each sun sensor and the possible mounting errors are stated in chapter 5.

• The KIPS Transactions:PartA
• /
• v.12A no.5 s.95
• /
• pp.451-460
• /
• 2005

We present a methodology to design energy-efficient data paths using FPGAs. Our methodology integrates domain specific modeling, coarse-grained performance evaluation, design space exploration, and low-level simulation to understand the tradeoffs between energy, latency, and area. The domain specific modeling technique defines a high-level model by identifying various components and parameters specific to a domain that affect the system-wide energy dissipation. A domain is a family of architectures and corresponding algorithms for a given application kernel. The high-level model also consists of functions for estimating energy, latency, and area that facilitate tradeoff analysis. Design space exploration(DSE) analyzes the design space defined by the domain and selects a set of designs. Low-level simulations are used for accurate performance estimation for the designs selected by the DSE and also for final design selection We illustrate our methodology using a family of architectures and algorithms for matrix multiplication. The designs identified by our methodology demonstrate tradeoffs among energy, latency, and area. We compare our designs with a vendor specified matrix multiplication kernel to demonstrate the effectiveness of our methodology. To illustrate the effectiveness of our methodology, we used average power density(E/AT), energy/(area x latency), as themetric for comparison. For various problem sizes, designs obtained using our methodology are on average $25\%$ superior with respect to the E/AT performance metric, compared with the state-of-the-art designs by Xilinx. We also discuss the implementation of our methodology using the MILAN framework.

• Journal of the Korean Institute of Traditional Landscape Architecture
• /
• v.29 no.1
• /
• pp.105-120
• /
• 2011

A moat is a pond or waterway paved on the outside of a fortress that is one of the facilities to prevent enemy from approaching the fortress wall or classify it as the boundary space, moats had existed in Europe, Asia and the America from ancient times to medieval times. however it is has been disappeared in modem society. In addition, a moat is a great value in historical and cultural sense such as offering a variety of cultural activities and habitats for animals, but unfortunately there is little consideration of its restoration plan. This research is aimed to investigate historical and cultural meaning and significance of moats which had been existing from ancient times to medieval times in the Eastern and Western. For this purpose, this research analyzed concepts and functions in consideration with times and ideological backgrounds of moats in Korea, China, and Japan. Results were as follows: 1. Moats in Korea existed not only in the castle towns of Goguryeo but also in ancient castle towns of Baekje and Silla. Natural moats and artificial moats existed around castles that were built to prevent and disconnect accessibility of enemies In Goryeo Dynasty and Chosun Dynasty, moats were also used as a defensive function. 2. A moat was generally installed by digging in the ground deep and wide at regular intervals from the ramparts, A moat was installed not only around a castle but also in its interiors. Moats outside castles played an important role in stomping the ground hard besides enhancing its defensive power. In addition, water bodies around a facility often discouraged people's access and walls or fences segregated space physically, but a moat with its open space had an alert and defensive means while pertaining its visual characteristics. 3. The moat found at Nagan Eupseong rumor has it that a village officials' strength was extremely tough due to strong energy of the blue dragon[Dongcheon] in Pungsujiri aspects, so such worries could be eliminated by letting the stream of the blue dragon flow in the form of 'S'. 4. The rampart of the Forbidden City of China is 7.9 meters high, and 3,428 meters long in circumference. It was built with 15 layers of bricks which were tamped down after being mixed with glutinous rice and earth, so it is really solid. The moat of the Forbidden City is 52 meters in width and 6 meters in depth, which surrounds the rampart of the Forbidden City, possibly blocking off enemies' approach. 5. Japan moats functioned as waterways due to their location in cities, further, with the arrangement of leisure facilities nearby, such as boating, fishing from boats, and restaurants, it helped relieve city dwellers' stress and functions as a lively city space. 6. Korean moats are smaller in scale than those of the Forbidden City of China, and Edo, and Osaka castles in Japan, Moats were mostly installed to protect royal palaces or castles in the Eastern Asia whereas moats were installed to protect kings, lords, or properties of wealthy people in the west.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.27 no.3
• /
• pp.155-162
• /
• 2014

Using an isogeometric approach, a continuum-based shape design optimization method is developed for steady state power flow problems at high frequencies. In case the isogeometric method is employed to the shape design optimization, the NURBS basis functions used in CAD geometric modeling are directly utilized to embed the exact geometry into the computational framework so that the design parameterization for shape optimization is much easier than that in the finite element method and consequently provides the enhanced smoothness of design perturbations. Thus, exact geometric models can be used in both the response and the shape sensitivity analyses, where normal vector and curvature are continuous over the whole design space so that enhanced shape sensitivity can be expected. Through numerical examples, the developed isogeometric sensitivity is compared with finite difference one to provide excellent agreement. Also, it turns out that the proposed method works very well in the shape optimization problems.

• Monthly Notices of the Royal Astronomical Society
• /
• v.501 no.4
• /
• pp.5616-5645
• /
• 2021

We analyse the large-scale clustering in Fourier space of emission line galaxies (ELG) from the Data Release 16 of the Sloan Digital Sky Survey IV extended Baryon Oscillation Spectroscopic Survey. The ELG sample contains 173 736 galaxies covering 1170 deg² in the redshift range 0.6 eff = 0.845 we measure D_V(z_eff)/r_drag = 18.33^+0.57_-0.62, with D_V the volume-averaged distance and r_drag the comoving sound horizon at the drag epoch. In combination with the RSD measurement, at z_eff = 0.85 we find fσ₈(z_eff) = 0.289^+0.085_-0.096, with f the growth rate of structure and σ₈ the normalization of the linear power spectrum, D_H(z_eff)/r_drag = 20.0^+2.4_-2.2 and D_M(z_eff)/r_drag = 19.17 ± 0.99 with D_H and D_M the Hubble and comoving angular distances, respectively. These results are in agreement with those obtained in configuration space, thus allowing a consensus measurement of fσ₈(z_eff) = 0.315 ± 0.095, D_H(z_eff)/r_drag = 19.6^+2.2_-2.1 and D_M(z_eff)/r_drag = 19.5 ± 1.0. This measurement is consistent with a flat ΛCDM model with Planck parameters.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.55 no.3
• /
• pp.141-145
• /
• 2006

The line current problem(2-dimensional space : point source) is not easy to analyze the magnetic field using the standard finite element method(FEM), such as overhead trolley line or transmission line. To supplement such a defect this paper is proposed the coupling scheme of analytical solution and FEM. In analysis of the magnetic field using the standard FEM. If the current region is a relatively small compared to the whole region. Therefore the current region must be finely divided using a large number of elements. And the large number of elements increase the number of unknown variables and the use of computer memories. In this paper, an analytical solution is suggested to supplement this weak points. When source is line current and the part of interest is far from line current, the analytical solution can be coupling with FEM at the boundary. Analytical solution can be described by the multiplication of two functions. One is power function of radius, the other is a trigonometric function of angle in the cylindrical coordinate system. There are integral constants of two types which can be established by fourier series expansion. Also fourier series is represented as the factor to apply the continuity of the magnetic vector potential and magnetic field intensity with tangential component at the boundary. To verify the proposed algorithm, we chose simplified model existing magnetic material in FE region. The results are compared with standard FE solution. And it is good agreed by increasing harmonic order.

• Journal of the Korea Furniture Society
• /
• v.26 no.1
• /
• pp.77-91
• /
• 2015

The appeal of sauna is caused by the fact that through that, one can feel Korea's unique temperament and culture; however, because of its being a public facility and flooding of businesses due to excessive supplies of various additional features such as washing, playing, eating, sleeping and health care functions, issues of social resources and environment come to the fore, so it has reached a situation of red ocean that it is difficult to enter the market anymore. Taking these into account, this study focused on developing a thermal technology and design of the housing of an environment-friendly mobile home sauna, making the most use of the sauna's fundamental purpose and settling it as a tourist product, analyzing the marketing research on the existing sauna and considering the recent housing trends and lifestyles for a new concept sauna. Thus, regarding its characteristics and utilization, it was designed smaller than $10m^2$ (3 pyeong) so that it would be easy to install in any space and convenient to move. It can be installed in separate buildings and rest spaces such as country houses, resorts, pensions, camping grounds as well as outdoor houses, custom produced for a measure of pyeong that customers want so as to match up with the Enforcement Ordinance of the Agricultural Land Act in a concept of the farmer's hut and kitchen, bathroom and bathroom can be installed inside according to an option. In addition, regarding its efficacy, in order to give environment-friendly healing effects, materials such as Hinoki Cypress, red clay and hardwood charcoal were used, a fixed indoor temperature of $70{\sim}100^{\circ}C$ was maintained by heating methods such as electromagnetic wave free, energy saving and low-power boiler, and it was made to have excellent effects on fatigue recovery, relieving stress, skin care and diet through far-infrared emission.

• Aerospace Engineering and Technology
• /
• v.11 no.1
• /
• pp.135-144
• /
• 2012

The NARO is South Korea's first carrier launch vehicle, which made its flights from NARO Space Center on 25 August 2009 and 10 June 2010. LV PACS(Preparation Automated Control System) is a electrical ground support system to monitor and control the integrated launch vehicle during the launch preparation and operation in Launch Complex. As a subsystem of LV PACS, LV PACS-II was developed for launch preparation and operation of the NARO upper stage, and all the functions and requirements were verified successfully through NARO flight tests. In this paper the core technology and characteristics applied to LV PACS-II are described.

• Journal of The Korean Astronomical Society
• /
• v.37 no.4
• /
• pp.159-169
• /
• 2004

This is a proposal to probe local part of the interplanetary dust (IPD) cloud complex and retrieve mean volume emissivity of the local IPDs at mid-infrared wavelengths. This will be done by monitoring, with Infrared Camera (IRC) aboard the ASTRO-F, the annual modulation of the zodiacal emission. In pointing mode of the ASTRO-F mission the spacecraft can make attitude maneuvering over approximately ${\pm}1^{\circ}$ range centered at solar elongation $90^{\circ}$ in the ecliptic plane. The attitude maneuvering combined with high sensitivity of the IRC will provide us with a unique opportunity observationally to take derivatives of the zodiacal emission brightness with respect to the solar elongation. From the resulting differential of the brightness over the ${\pm}1^{\circ}$ range, one can directly determine the mean volume emissivity of the local IPDs with a sufficient accuracy to de-modulate the annual emissivity variations due to the Earth's elliptical motion and the dis-alignment of the maximum IPD density plane with respect to the ecliptic. The non-zero eccentricity ($e_{\oplus}$= 0.0167) of the Earth's orbit combined with the sensitive temperature dependence of the Planck function would bring modulations of amplitude at least $3.34\%$ to the zodiacal emission brightness at mid-infrared wavelengths, with which one may determine the IPD temperature T(r) and mean number density n(r) as functions of heliocentric distance r. This will in turn fix the power-law exponent $\delta$ in the relation $T(r) = T_o(r/r_o)^{-\delta}$ for the dust temperature and v in $n(r) = n_o(r/r_o)^-v$ for the density. We discuss how one may de-couple the notorious degeneracy of cross-section, density, reference temperature $T_o$ and exponent $\delta$.