• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1999년도 추계학술대회 논문집 - 한국공작기계학회
• /
• pp.74-80
• /
• 1999

Work roll wear in the cold rolling of mild steel strip is strongly affected by rolling materials, rolling conditions such as roll arrangement in the cold rolling mill and lubrication. The tests were performed to find the effects of roll arrangement n the cold rolling mill on the work roll wear under the same lubricating conditions. The obtained results are as follows:If the distance of cold rolling is about 60km, the surface roughness of its was reduced by half(Ra 0.49${\mu}{\textrm}{m}$) and Pc(peak count) also was decreased to 60 ea/cm.It is easier for CC(Continuous casting) to make a slip on rolling than IC(Ingot casting). It is due to surface mirror in which first residual product appears and iron powder included Al2O3 is sticked. Because bending degree of 4Hi-rolling mill is higher than 6Hi-rolling mill, the first surface mirror was occurred to its center-point which is loaded strongly. 6Hi-rolling mill shape-controlled by intermediate roll doesn't need the initial crown to work roll. Therefore, fatigue and wear would appear a little bit.

• 한국세라믹학회지
• /
• 제54권2호
• /
• pp.121-127
• /
• 2017

Gadolinium tetraboride ($GdB_4$) was synthesized by reduction of $Gd_2O_3$ using boron carbide in presence of carbon. Effect of temperature on product quality was investigated. Pure $GdB_4$ powder was obtained in vacuum at $1500^{\circ}C$. Pressureless sintering experiments revealed that sintering takes place only above $1600^{\circ}C$. A maximum density of 77.1% of the theoretical value was obtained at $1800^{\circ}C$ by pressureless sintering. Hot pressing resulted in 95.5% of theoretical density at the lower temperature of $1700^{\circ}C$ under 35 MPa pressure. Hardness and fracture toughness of dense $GdB_4$ were measured and found to be 21.4 GPa and $2.3MPa{\cdot}m^{1/2}$, respectively. After exposure to air at $900^{\circ}C$, the formation of a porous and non-protective oxide layer was observed.

• 한국세라믹학회지
• /
• 제43권5호
• /
• pp.309-314
• /
• 2006

We synthesized lithium zirconate using solid-state reaction and analyzed thermal properties (TG/DTA) of starting materials and the synthesized one. When $Li_2ZrO_3$ powder was exposed to $CO_2$ environment at $500^{\circ}C$, 93% of the theoretical absorption weight was gained within 280 min with fairly high sorption rate. Almost all the absorbed $CO_2$ was generated by heating the sample to $800^{\circ}C$. We also investigated densification behavior of $Li_2ZrO_3$ under $CO_2$ environment. By sintering $Li_2ZrO_3$ at $760^{\circ}C$ using 2-step process, we obtained dense product, composed mainly of $Li_2ZrO_3\;and\;ZrO_2$, with relative density of 92%.

• 약학회지
• /
• 제37권2호
• /
• pp.172-181
• /
• 1993

The purpose of this study was to evaluate the clinical efficacy and safety of NRM which was newly developed as a combination product containing antacids, digestive enzyme and herbal drugs, and OTA powder, called OHTA'S ISAN on the morret, for the treatment of various symptoms in upper gastrointestinal diseases. 63 patients were recruited, 36 as a treated group with NRM and 27 as a controlled one with OTA. Patients were randomly allocated to receive either NRM or OTA t.i.d. for treatment of upper G-1 symptoms and undergone endoscopic, symptomatic and clinical laboratory assessments before and after 2 weeks. The results were as follows; 1. The general improvement rates of subjective symptoms in upper G-1 diseases were observed in 100%(32/32) for NRM and in 92%(23/25) for OTA. 2. The overall effective rates in terms of the symptoms and endoscopic findings were 88.9%(32/36) for NRM and 85.2%(23/27) ,or OTA respectively. 3. In NRM group, no significant side effects by NRM were observed except a mild and transient vomiting in one patient, but in OTA group treatment was discontinued due to nousea in one patient, However, there were no clinically significant changes detected in the laboratory parameters. According to the result of this trial, it is cocluded that NRM was safe and effective and (but not statistically significant) was superior to OTA in the treatment of gastrointestinal diseases caused by gastritis, gastric and duodenal ulcer, functional gastrointestinal disorder, non-ulcer dyspepsia etc.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1994년도 추계학술대회 논문집 학회본부
• /
• pp.202-204
• /
• 1994

Nowadays Perovskite $La_{1-x}Sr_xCoO_3$ is a preferred cathode material in the construction Solid Oxide Fuel Cell (SOFC). The $La_{1-x}Sr_xCoO_3$ with Sr contents ranging from X=0.0 to X=1.0 were prepared by a citrate method. All samples were examined by X-ray powder diffraction. The samples used for measuring thermal expansion were prepared as pellets by cold pressing and subsequent sintering in air at $1200^{\circ}C$ for 5 hours. To measure the sub-product of $La_{1-x}Sr_xCoO_3$ with YSZ, where coating films were sintered at $1200^{\circ}C$ for 5 hour.

• 한국미생물·생명공학회지
• /
• 제47권2호
• /
• pp.234-241
• /
• 2019

In Korea, traditional doenjang is manufactured using the conventional method at home and by small-scale enterprises. Because this age-old process depends on natural inoculation of various microorganisms, it is difficult to reproduce or maintain consistency in the final product quality across batches. Moreover, doenjang occasionally prepared by this method raises safety concerns related to aflatoxin, biogenic amine, and Bacillus cereus contamination. To develop starters that can be conveniently used at home or in small industry settings for the manufacturing of safe and flavor-improved doenjang, autochthonous microbe starters were developed in dried forms as ready-to-use starters. Each starter powder prepared by heat- or freeze-drying methods remained stable even after 24-week storage. These ready- to-use starter powders were successfully applied to lab-scale fermentation for the production of safe and flavor-improved doenjang. We believe that these ready-to-use starter powders will benefit small-scale enterprises in the manufacturing of doenjang of good reproducible quality.

• 자원리싸이클링
• /
• 제28권6호
• /
• pp.18-25
• /
• 2019

폐니켈수소전지에 함유되어 있는 세륨을 회수하기 위하여 침출 및 침전을 통해 회수한 희토류복합 침전분말을 수산화나트륨(NaOH) 수용액에 반응온도 70 ℃ 및 반응시간 4시간의 조건에서 이온치환반응을 통하여 희토류 수산화물로 변환시켰다. 이후 희토류 수산화물은 반응온도 80 ℃에서 반응시간 4시간의 조건에서 공기를 주입하며 산화반응을 통해 세륨을 Ce³⁺에서 Ce⁴⁺로 전환시켰다. 세륨의 산화율은 XPS 분석을 통해 약 25 %로 확인하였으며, 산화반응이 완료된 분말은 묽은 황산에 대한 용해도 차이를 이용하여 세륨과 나머지 희토류를 분리하였다. 최종적으로 회수된 분말은 XRD 분석을 통해 수산화세륨(Ce(OH)₄)의 결정상을 확인하였으며, 이때 세륨의 순도는 약 94.6 %, 회수율은 97.3 %를 나타내었다.

• 한국축산식품학회지
• /
• 제38권5호
• /
• pp.866-877
• /
• 2018

Cheese emulsion is an intermediate product for the production of cheese powder and needs to be stable, homogeneous and pumpable characteristics to convey to the spray drier. This study was conducted to evaluate the effects of fat reduction and emulsifying salt (ES) amount in cheese emulsion systems on the physicochemical characteristics. Reduced-fat (RF) and full-fat (FF) white-brined cheese emulsions were produced with different dry matters (DM; 15%-25% excluding ES) and ES concentrations (0%-3% based on cheese weight). Stable cheese emulsion was obtained at lower DM in RF cheese emulsion than that of FF cheese emulsion. Reduction in the amount of ES resulted in instability of both emulsions. Apparent viscosity with pseudoplastic flow behavior significantly increased with the decrease of fat content in stable cheese emulsions. Microstructure of emulsions appeared to be related to the fat content, stability and degree of emulsification. Reduction of fat content caused to get less lightness and more greenness in color, whereas yellowness was significantly decreased by increase in the amount of ES. In conclusion, fat reduction resulted in higher viscosities of cheese emulsion due to inducing the increment of protein, and the addition amount of ES considered as very important factor to produce stable cheese emulsion without protein precipitation or cream separation. Therefore, for preparation of RF cheese emulsion using a variety of white-brined cheese, lower amounts of DM would be suggested in this study to obtain homogenous droplets in the atomizing process of spray drying.

• 한국분말재료학회지
• /
• 제27권2호
• /
• pp.111-118
• /
• 2020

The convergence of artificial intelligence with smart factories or smart mechanical systems has been actively studied to maximize the efficiency and safety. Despite the high improvement of artificial neural networks, their application in the manufacturing industry has been difficult due to limitations in obtaining meaningful data from factories or mechanical systems. Accordingly, there have been active studies on manufacturing components with sensor integration allowing them to generate important data from themselves. Additive manufacturing enables the fabrication of a net shaped product with various materials including plastic, metal, or ceramic parts. With the principle of layer-by-layer adhesion of material, there has been active research to utilize this multi-step manufacturing process, such as changing the material at a certain step of adhesion or adding sensor components in the middle of the additive manufacturing process. Particularly for smart parts manufacturing, researchers have attempted to embed sensors or integrated circuit boards within a three-dimensional component during the additive manufacturing process. While most of the sensor embedding additive manufacturing was based on polymer material, there have also been studies on sensor integration within metal or ceramic materials. This study reviews the additive manufacturing technology for sensor integration into plastic, ceramic, and metal materials.

• 한국재료학회지
• /
• 제25권12호
• /
• pp.659-665
• /
• 2015

The self-propagating high temperature synthesis approach was applied to synthesize amorphous boron nano-powders in argon atmospheres. For this purpose, we investigated the characteristics of a thermally induced combustion wave in the $B_2O_3+{\alpha}Mg$ system(${\alpha}=1.0-8.0$) in an argon atmospheres. In this study, the exothermic nature of the $B_2O_3-Mg$ reaction was investigated using thermodynamic calculations. Experimental study was conducted based on the calculation data and the SHS products consisting of crystalline boron and other compounds were obtained starting with a different initial molar ratio of Mg. It was found that the $B_2O_3$ and Mg reaction system produced a high combustion temperature with a rapid combustion reaction. In order to regulate the combustion reaction, NaCl, $Na_2B_4O_7$ and $H_3BO_3$ additives were investigated as diluents. In an experimental study, it was found that all diluents effectively stabilized the reaction regime. The final product of the $B_2O_3+{\alpha}Mg$ system with 0.5 mole $Na_2B_4O_7$ was identified to be amorphous boron nano-powders(< 100 nm).