• Proceedings of the SAREK Conference
• /
• 2009.06a
• /
• pp.751-756
• /
• 2009

In the perspective of saving energy in buildings, the high performance of insulation and air tightness for improving the heating and the cooling efficiency, has brought economically positive effects. However, these building energy saving technologies cause the lack of ventilation, which is the direct cause of increasing the indoor contaminants, and is also very harmful to the residents, because they spend over 90% of their time indoors. Therefore, the ventilation is important to keep the indoor environment clean and it can also save the energy consumption. In this study, a HEPA type nano ceramic filter is designed as a passive ventilation system to collect airborne particles and to supply fresh outdoor air. The double layer filter, which has $30{\mu}m$ in diameter at the conditions of 10wt% of concentration and 3kV/cm of the electric intensity, is produced by electrospinning. The filtration coating technology is confirmed in the solution with $SiO_2$ nano particles using polymer nano fibers. Also double layer filters are coated with $SiO_2$ nano particles and finally the porous construction materials are made by sintering in the electric furnace at $200{\sim}1400^{\circ}C$. The efficiency is measured 96.67% at the particle size of $0.31{\mu}m$, which is slightly lower than HEPA filter. However the efficiency is turned out to be sufficient.

• Journal of the Korean Applied Science and Technology
• /
• v.30 no.1
• /
• pp.146-151
• /
• 2013

This paper reveals the performance decrease and recovery of PEMFC when the contaminated fuel gas and air source with sulfur impurities such as hydrogen sulfide and sulfur dioxide were simultaneously introduced to anode and cathode, respectively. Three different GDLs were fabricated with different carbon black and activated carbon to prevent an introduction of sulfur compound impurities into MEA. components. The severity of $SO_2$ and $H_2S$ poisoning was depended on concentrations(3 ppm - 10 ppm) of sulfur impurities. Especially, cell performance degradation rate was rapid when MEA fabricated with CN-2 GDL because it had little porosity on GDL surface. Moreover, the cell performance can be recovered up to 90%-95% only with neat hydrogen and fresh air feeding.. Conclusively, MEA fabricated with porous CN-1 GDL showed the best cell performance and recovery efficiency during exposure to poisoning condition by simultaneous sulfur impurities.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.45 no.2
• /
• pp.92-98
• /
• 2017

Porosity in polymer matrix composites generated during pyrolysis process affect the thermomechanical behavior of the composites. In this paper, multislice finite element models for the porous composite materials are developed, and poroelastic and failure analysis for these models are performed. In order to investigate the three-dimensional effects, finite element meshes are modeled considering different porosity(up to 0.5) and the number of slices (up to five). As a result, effective Young's moduli and poroelastic parameters exhibit the maximum differences of 74.0% and 442.1% with respect to porosity respectively, and 98.7% and 37.2% with respect to the number of slices. First and last failure strengths are decreased 88.2% and 90.0% with respect to porosity respectively, and 53.8% and 171.8% with respect to the number of slices.

• Membrane Journal
• /
• v.30 no.5
• /
• pp.326-332
• /
• 2020

In this study, polymer-fluorinated silica composite hollow fiber membranes were fabricated and applied to a membrane contactor for the recovery of methane dissolved in the anaerobic effluent. To prepare the composite membranes, porous hollow fiber substrates were fabricated with Ultem^®, a commercial polyetherimide (PEI). Subsequently, fluorinated silica particles were synthesized and coated on the surface via strong covalent bonding. Due to the high porosity, our membrane showed a CH₄ flux of 8.25 × 10^-5 ㎤ (STP)/㎠·s at the liquid velocity of 0.03 m/s which is much higher that that of commercial polypropylene membrane designed for degassing processes. This is attributed to our membrane's high porosity as well as a superior surface hydrophobicity (120~122°) resulted from the coating with fluorinated silica nanoparticles.

• Journal of the Korean Electrochemical Society
• /
• v.11 no.1
• /
• pp.16-21
• /
• 2008

The key component of a direct methanol fuel cell (DMFC) is the membrane electrode assembly (MEA), which comprises a polymer electrolyte membrane and catalyst layers (anode and cathode electrode). Generally the catalyst layer is coated on the porous electrode supporter (e.g. carbon paper or cloth) using various coating methods such as brushing, decal transfer, spray coating and screen printing methods. However, these methods were disadvantageous in terms of the uniformity of catalyst layer thickness, catalyst loss, and coating time. In this work, we used bar-coating method which can prepare the catalyst layer with uniform thickness for MEA of DMFC. The surface and cross-section morphologies of the catalyst layers were observed by SEM. The performances and resistance of the MEAs were investigated through a single cell evaluation and impedance analyzer.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.480-480
• /
• 2011

양극산화(anodization)는 금속을 전기화학적으로 산화시켜 금속산화물로 만드는 기술로서 최근 다양한 크기의 나노 구조를 제조하는 기술로 각광받고 있으며, 이러한 기술에 의하여 얻어지는 anodic aluminum oxide(AAO)는 magnetic data storage, optoelectronic device, sensor에 적용될 수 있는 nano device 뿐만 아니라 nanostructure를 제조하기 위한 template 및 mask로써 최근 광범위 하게 연구되고 있다. 또한, AAO는 Al2O3의 단단한 구조를 가진 무기재료이므로 solid mask로써 다른 porous materials 보다 뛰어난 특성을 갖고 있다. 또한 electron-beam lithography 및 block co-polymer 에 의한 patterning 과 비교하여 매우 경제적이며, 재현성이 우수할 뿐만 아니라 대면적에서 나노 구조의 크기 및 형상제어가 비교적 쉽기 때문에 널리 사용되고 있다. 그러나, AAO 형성 시 생기게 되는 반구형 모양의 barrier layer는 물질(substance)과 기판과의 direct physical and electrical contact을 방해하기 때문에 해결해야 할 가장 큰 문제점 중 하나로 알려져 있다. 따라서 본 연구에서는 실리콘 기판위의 형성된 AAO의 barrier layer를 Cl/BCl3 gas mixture에서 Neutral Beam Etching (NBE)과 Ion Beam Etching (IBE) 로 각각 식각한 후 그 결과와 비교하였다. NBE와 IBE 모두 Cl2/BCl3 gas mixture에서 BCl3 gas의 첨가량이 60% 일 경우 etch rate이 가장 높게 나타났고, optical emission spectroscopy (OES)로 Cl2/BCl3 플라즈마 내의 Cl radical density와 X-ray photoelectron spectroscopy (XPS)로 AAO 표면 위를 관찰한 결과 휘발성 BOxCly의 형성이 AAO 식각에 크게 관여함을 확인 할 수 있었다. 또한, NBE와 IBE 실험한 다양한 Cl2/BCl3 gas mixture ratio 에서 AAO가 식각이 되지만, 이온빔의 경우 나노사이즈의 AAO pore의 charging에 의해 pore 아래쪽의 위치한 barrier layer를 어떤 식각조건에서도 제거하지 못하였다. 하지만, NBE에서는 BCl3-rich Cl2/BCl3 gas mixture인 식각조건에서 AAO pore에 휘발성 BOxCly를 형성하면서 barrier layer를 제거할 수 있었다.

• Applied Biological Chemistry
• /
• v.35 no.1
• /
• pp.36-41
• /
• 1992

Several commercial cottonseed, corn and rapeseed oils were stored at $60^{\circ}C\;and\;70^{\circ}C$ with daily exposure of fluorescent light for 12 hours and evaluated their rancidity by headspace gas chromatographic analysis of pentanal and hexanal. The data of gas chromatographic analysis was compared with organoleptic flavor evaluation. For headspace gas chromatographic analysis, the volatile compounds were recovered by porous polymer trap and flushed into a fused silica capillary column at $250^{\circ}C$. Twenty-three GC peaks were identified on the basis of relative retention time of reference compounds and gas chromatography-mass spectrometry. The results showed that the contents of pentanal and hexanal were linearly increased during storage. A very simple linear relationship was found between organoleptic flavor scores and amounts of two volatile compounds with very high correlation coefficient. This results suggested the possible implication of pentanal and hexanal as an quality index for rancidity evaluation of cottonseed, corn and rapeseed oils.

• Journal of the Korean Ceramic Society
• /
• v.41 no.7
• /
• pp.528-533
• /
• 2004

Macroporous SiC with pore size 84∼658 nm and mesoporous SiC with pore size 15∼65 nm were respectively prepared by infiltrating low viscosity preceramic polymer solutions into the various sacrificial templates obtained by natural sedimentation or centrifuge of 20∼700 nm silica sol, which were subsequently etched off with HF after pyrolysis at 1000∼140$0^{\circ}C$ in an argon atmosphere. Three-dimensionally long range ordered macroporous SiC ceramics derived from polymethylsilane (PMS) showed surface area 584.64$m^2$g$^{-1}$ when prepared with 112nm silica sol and at 140$0^{\circ}C$, whereas mesoporous SiC from polycarbosilane (PCS) exhibited the highest surface area 619.4 $m^2$g$^{-1}$ with random pore array when prepared with 20-30 nm silica sol and at 100$0^{\circ}C$. Finally, tile pore characteristics of porous SiC on the types of silica sol, polymers and pyrolytic conditions were interpreted with the analytical results of SEM, TEM, and BET instruments.

• Membrane Journal
• /
• v.26 no.2
• /
• pp.146-151
• /
• 2016

Sulfonated poly (arylene ether sulfone) (SPAES) random copolymers have merits such as high proton conductivity, relatively low production cost, and thermochemical resistance when applied as polymer electrolyte membranes for fuel cells. However, it is difficult to directly employ SPAES copolymers into practical fuel cell membrane applications owing to their low chemical stability and dimensional instability under harsh operation conditions. A plausible solution is to impregnate SPAES copolymers into support films (e.g., electrospun polyimide support) with interconnected pore structures and high thermochemical toughness. In this study, a SPAES copolymer with a swivel group, which induces high free volume for fast ion transport, is chosen as ionomers to prepare pore-filling membranes (PFMs). The feasibility of the resulting membranes is evaluated via membrane characterizations.

• Membrane Journal
• /
• v.22 no.3
• /
• pp.191-200
• /
• 2012

New composite membranes were manufactured by impregnating post-sulfonated poly(arylene ether sulfone)s containing perfluorocyclobutane (PFCB) groups into porous polytetrafluoroethylene (PTFE) films. Two kinds of post-sulfonated poly(arylene ether sulfone)s with two different monomer ratios (sulfonable biphenylene monomer : non-sulfonable sulfonyl monomer = 6 : 4, 4 : 6) were first prepared through three synthetic steps: synthesis of trifluorovinylether-terminated monomers, thermal cycloaddition polymerization and post-sulfonation using chlorosulfonic acid (CSA). The composite membranes were then prepared by adjusting the concentrations (5~20 wt%) of the resulting copolymers impregnated in the PTFE films. The water uptake, ion exchange capacity (IEC) and ion conductivity of the composite membranes were characterized and compared with their unreinforced dense membranes and Nafion. All the synthesized compounds, monomers and polymers were characterized by $^1H$-NMR, $^{19}F$-NMR and FT-IR and the composite membranes were observed with scanning electron micrographs (SEM).