• Membrane and Water Treatment
• /
• v.10 no.6
• /
• pp.431-440
• /
• 2019

A novel composite membrane was synthesized using crosslinked polyamide and fly ash ceramic substrate for phenol removal. Glutaraldehyde was used as crosslinker. Characterization shows that synthesized membrane possesses good permeability ($0.184l.m^{-2}.h^{-1}.kPa^{-1}$), MWCO (1.7 kDa), average pore size (1.08 nm) and good chemical stability. RSM was adopted for phenol removal studies. Box-Behnken-Design using quadratic model was chosen for three operating parameters (feed phenol concentration, pH and applied pressure) against two responses (phenol removal, flux). ANOVA shows that model is statistically valid with high coefficient of determination ($R^2$)value for flux (0.9897) and phenol removal (0.9302). The optimum conditions are obtained as pH 2, $46mg.l^{-1}$ (feed phenol concentration) and 483 kPa (applied pressure) with 92.3% phenol removal and $9.2l.m^{-2}.h^{-1}$ flux. Data validation with deviation of 4% confirms the suitability of model. Obtained results reveal that prepared composite membrane can efficiently separate phenol from aqueous solution.

• Elastomers and Composites
• /
• v.55 no.4
• /
• pp.339-346
• /
• 2020

We functionalized a wear-resistant carbon-based MoS2 filler to solve its limited wear condition problem. The filler exhibits excellent lubricative properties. The surface modification of MoS2 was carried out using a (3-glycidyloxypropyl)trimethoxysilane (GPTMS) silane coupling agent to improve the low compatibility and dispersibility of the filler that generally degrade the performance of composites. A silane coupling agent was employed for the functionalization of MoS2, and its effect on the wear resistance of MoS2/Polyamide-6,6 was investigated. The silanization of MoS2 was identified by contact angle analysis and Fourier-transform infrared, energy dispersive X-ray, and X-ray photoelectron spectroscopies. The wear resistance of the composite was found to be improved significantly by the surface functionalization of MoS2.

• Elastomers and Composites
• /
• v.52 no.1
• /
• pp.59-68
• /
• 2017

The effect on the hydrolysis resistance properties by the addition of maleic anhydride grafted EMDM (MA-g-EPDM) and PP (MA-g-PP) to a PA66/GF composite was investigated with respect to the mechanical properties, thermal properties, and morphology. The degree of hydrolysis of the PA66/GF composite was measured using py-GC/MS analysis. When compared to the PA66/GFcomposite in MEG/water solution, the composites where MA-g-EPDM and MA-g-PP were added to PA66/GF showed a higher degree of hydrolysis resistance, impact strength, and thermal properties, whereas their tensile strength, tensile modulus, flexural strength and flexural modulus decreased. As immersion time in the solution increases, the rate of tensile strength drop of the MA-g-PP added composite appeared lower than that of the PA66/MA-g-EPDM/GF and PA66/GF composites. The py-GC/MS analysis confirmed the formation of PA66 hydrolysis reaction by products such as carboxylic acid and alkylamine with increasing immersion time.

• Applied Chemistry for Engineering
• /
• v.7 no.1
• /
• pp.194-202
• /
• 1996

Hot melt adhesive based on the polyamide resin was studied to improve the conventional hot melt adhesives such as ethylene-vinyl acetate which have inherent problems against creep and heat resistance. It was found that the terpolymer of nylons6, nylon66, and nylon12 or the nylon blend instead of nylon homopolymer was suitable base resin for hot melt adhesives, since the disruption of regularity in the polymer chains reduced the crystallinity, resulting in lower melting point and melt viscosity. Also, the rheological properties of the polyamide based hot melt adhesive could be controlled by the incorporation of terpene resin, butyl benzyl phthalate, and paraffin wax. The results of melt viscosities and tensile properties of adhesive itself indicated that the optimum adhesion properties could be obtained through the blending of CM831/843P resins with weight ratio 75/25~50/50. The adhesion between steel and steel was tested by using lap shear geometry. It was found that the surface roughness of steel affected the adhesion strength.

• Korean Membrane Journal
• /
• v.7 no.1
• /
• pp.58-66
• /
• 2005

Nanofiltration (NF) of a dyeing wastewater was carried out using polyamide NF-membranes. Before applying the wastewater to the membrane process, it was pretreated with various chemical coagulants such as alum, ferric chloride and HOC-100A. In order to see the effect of the pretreatment of the wastewater using chemical coagulants on the membrane separation process, the optimum conditions for the coagulation and sedimentation process using the chemical coagulants were sought. By the pretreatment, despite the different coagulants used, the chemical oxygen demand (COD) and UV-absorbance of the wastewater were lowered by more than $70\%$. The pretreated wastewater was then applied to the membrane process. The effect of the coagulants used for the pretreatment on the membrane fouling was studied. From this study, it was found that the HOC-100A was the best out of the coagulants used far the removal of the materials that could cause membrane fouling.

• Bulletin of the Korean Chemical Society
• /
• v.28 no.12
• /
• pp.2359-2362
• /
• 2007

MALDI-TOF-MS technique was applied to obtain structural and compositional information of synthetic polyamides, Nylon6 and Nylon66. Mass spectra of both the original and the hydrolyzed polyamide samples were analyzed using the self calibration method as well as the internal calibration method with the standard materials of known masses. The MALDI-TOF mass spectra of Nylon6 samples showed the presence of protonated, sodiated, and potassiated ions that were assigned to cyclic and NH2/COOH terminated linear oligomers. From the MALDI-TOF mass spectra of Nylon66 samples, the potassiated linear oligomers with three different end groups are identified as well as the cyclic oligomers, i.e., NH2/COOH terminated oligomers, NH2/NH2 terminated oligomers, and COOH/COOH terminated oligomers. Full characterization of the molecular species and end groups present in the polyamide samples has been achieved, and also the changes in mass spectral patterns after the hydrolysis of the samples are presented.

• Journal of the Korean Society of Industry Convergence
• /
• v.24 no.6_2
• /
• pp.819-825
• /
• 2021

In the industry, the use of lightweight bearings is increasing to minimize motor power loss, and in particular, the application of next-generation systems such as robots and drones is increasing. Bearing manufacturers are producing lightweight bearings by changing the bearing material, but related researches is insufficient. In this paper, life test and structural analysis were performed for lightweight bearings, and shape parameters and scale parameters were derived based on the life test results. It was confirmed that the shape parameter was 2.52 and the scale parameter was 164 hours. As a result of calculating the dynamic load rating based on the B₁₀ life, it was confirmed that the dynamic load rating of the lightweight bearing was 7% compared to the formula suggested by ISO 281. The reason is that the material of the retainer, which is a major failure part, is a polyamide 66 series that reacts sensitively to heat, so It is judged to show a lot of difference from the ISO 281 calculation formula.

• Polymer(Korea)
• /
• v.36 no.6
• /
• pp.712-720
• /
• 2012

Thermal degradation for glass fiber-reinforced polyamide 66 composite (PA 66) with respect of thermal exposure time has been investigated using optical microscopy, scanning electron microscopy and Fourier transform infrared spectroscopy. As the thermal exposure time was prolonged, a slight increase in tensile strength for only initial stage and afterward, a proportional decrease of tensile strength was observed. These results can be explained by the increase of crystallinity, followed by the increase of crosslinking density, chain scission and the decrease in chain mobility, due to thermal oxidation with the exposure time. Fourier transform infrared spectroscopy results showed the increase of ketone peak and silica peak on the surface of thermally exposed PA 66. In addition, the thermal decomposition kinetics of PA 66 was analyzed using thermogravimetric analysis at three different heating rates. The relationship between activation energy and lifetime-prediction of PA 66 was investigated by several methodologies, such as statistical tool, UL 746B, Ozawa and Kissinger. The activation energy determined by thermogravimetric analysis had a relatively large value compared with that from the accelerated test. This may result in over-estimating the lifetime of PA 66. In this study, a master curve of exponential fitting has been developed to extrapolate the activation energy at various service temperatures.

• Proceedings of the Korean Fiber Society Conference
• /
• 2003.04a
• /
• pp.165-168
• /
• 2003

Nylon was the first commercialized synthetic fiber. It is a polyamide, derived from a diamine and dicarboxylic acid. The nylon fiber has outstanding durability and excellent physical properties such as stiffness, wear and abrasion resistance, friction coefficient and chemical resistance. Due to these properties of nylon 66, nano-sized fibers are produced by electrospinning method in this study. During the past years the nylon 66 fibers have been prepared by conventional melt spining. (omitted)

• Elastomers and Composites
• /
• v.55 no.2
• /
• pp.137-146
• /
• 2020

Part 1 provides a theoretical introduction of the hydrolysis mechanism, while Part 2 introduces other types of reaction mechanisms after hydrolysis in elastomer and PA66 composites. We reviewed the condensation reaction, which occurs after hydrolysis in bi-functional alkoxy silane (TESPD & TESPT), and investigated its effects on the mechanical properties of the composites. We also reviewed activators such as zinc soap, which enhances the mechanical properties of silica-silane-filled elastomer composites. The interaction parameter of silica-silane-filled elastomer composites [α_C (alpha C)] were also discussed. The effects of hydrolysis on the mechanical property changes in plastic composites were compared and reviewed.