• Asian-Australasian Journal of Animal Sciences
• /
• 제19권7호
• /
• pp.1054-1058
• /
• 2006

The purpose of this study was to use pig blood plasma transglutaminase (TGase) combined with thrombin and fibrinogen as a binder, which was applied to restructured meat, and to investigate its effect on the restructured meat quality. Pig meat was obtained 10 h post mortem from a traditional market was ground using a 10 mm aperture plate. A binder admixture was added (TGase:thrombin:fibrinogen mixed as 0.5:1:20 (v/v/v) to which was added 12% of its volume of 0.25 M calcium chloride) at 0, 5, 10, 15 and 20% of meat weight. Measurements included cooking loss, shrinkage rate, shear value, total plate count, pH value, TBA value, color difference, tension strength and sensory evaluation. The results showed that ground meat containing 20% w/w of binder admixture had higher cooking loss, shrinkage rate and shear value (p<0.05). Addition of different percentages of binder admixture did not affect total plate count, pH value, TBA value, and sensory evaluation of restructured meat (p>0.05). Tension strength was increased with increased level of binder admixture. Addition up to 15% binder admixture to restructured meat showed better scores of sensory texture, flavor and total acceptability (p<0.05).

• 한국인쇄학회지
• /
• 제29권3호
• /
• pp.133-142
• /
• 2011

We produce a photosensitive convex plate to research a Nickel metal relief printing plate using galvanic process. A Method for preparing DLC convex plate that is metalized on Nickel metal relief printing plate using CVD(Chemical Vapor Deposition) process and $N_2DLC$-convex plate that is DLC metalized thin film layer of $N_2$ plasma surface treatment are comprised. DLC thin film layers on Nickel surface are fragile. The results of the research indicate that the coefficient of friction on DLC metalized thin film layer is relatively low than Nickel surface and the durability of Nickel surface coated DLC metalized thin film layer is superior to Nickel surface. A relative evaluation of three form plate wetting properties using varnish liquid-drop plate indicates superior printing aptitudes for $N_2DLC$, DLC, Nichel plate order as above.

• 한국전기전자재료학회논문지
• /
• 제32권4호
• /
• pp.320-326
• /
• 2019

Recently, the application of atmospheric plasma technology in air filtration is increasing. Sterilization by an atmospheric plasma device is very effective. However, ozone gas, which is generated during atmospheric plasma formation, poses a hazard to human health. To reduce the ozone gas during plasma discharge, we fabricated a one-plate hybrid plasma discharge device with a heating element, which can decompose ozone gas effectively by a simple heating action. In this study, we evaluated the plasma discharge characteristics and ozone concentrations with various Ar flow rates and temperatures. With increasing Ar gas flow rate, the ozone concentration and spectrum intensity increased till an Ar gas flow rate of 60 sccm, and decreased thereafter. When discharged in high temperature, the ozone concentration and spectrum intensity decreased. Further, to evaluate the state of the treated surface under various plasma discharge and heating conditions, we measured the variation in the contact angles on the surface. Regardless of the temperature, the contact angle increased with increasing discharge voltage. However, the contact angle increased when discharged at high temperature.

• 전기학회논문지
• /
• 제56권3호
• /
• pp.583-587
• /
• 2007

Corona discharge and ozone generation characteristics of a slit dielectric barrier discharge type wire-plate plasma reactor with a third electrode have been investigated. When a third electrode is installed on a slit of the slit barrier, where an intense corona discharge occurs, it is found that a significantly increased ozone output could be obtained. This, however, indicates that the third electrode can activate the corona discharges both of the discharge wire and the slit of the slit barrier in the plasma reactor. As a result, a thin stainless wire, used as the third electrode has a strong effect to influence the corona discharge of the slit and corona wire, especially to the negative corona discharge. Higher amounts of the output ozone and ozone yield, about 1.27 and 1.29 times for the negative corona discharge, can be obtained with the third electrode, which reveals the effectiveness of the third electrode.

• Journal of Welding and Joining
• /
• 제9권4호
• /
• pp.69-74
• /
• 1991

The Plasma Arc Cutting Method using high density and hight temperature beam is well applicable to the cutting of the nonferrous metal (Al alloy ) and stainless steel which are unable to be cut by the use of the oxy-fuel gas. This study focalizes on the cutting phenomena of the plate of (mm) thickness, since the cutting phenomena of thick plates have been rather thoroughly studied. In this study the cutting groove, adhesive phenomena of dross, surface roughness were measured according to the variation of cutting speed and compared with the case of mild steel plates. The result showed that the kerf width variation of Al alloy was similar to the case of mild steel, while that of the stainless steel differed from the mild steel. In the adhesive phenomena of dross, 6(mm) thick plates of Al alloy showed a difference from those of thick plates, but the stainless steel was similar to thick plates. The surface roughness variation of Al alloy wias minimum at 67 cm/min, while that of stainless steel was at 30cm/min.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1994년도 하계학술대회 논문집 C
• /
• pp.1292-1294
• /
• 1994

With the contact angle of phase epoxy resin on the inorganic filler(glass plate) surface treated with air plasma, we have studied about the interface between epoxy resin and glass plate as simple model of a glass fiber reinforced composite materials. The contact angle on the inorganic filler surface varied with surface treatment conditions. The contact angle significantly depends on plasma treating time and environment temperature of the oven.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2006년도 춘계 학술대회 개요집
• /
• pp.178-180
• /
• 2006

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2006년도 추계학술발표회 초록집
• /
• pp.31-32
• /
• 2006

• 한국레이저가공학회지
• /
• 제17권2호
• /
• pp.19-25
• /
• 2014

Optical embedded diffraction gratings with the bulk modification in BK-7 glass plates excited by tightly focused high-intensity femtosecond (130fs) Ti: sapphire laser (peak wavelength = 790nm) were demonstrated. The structural modifications with diameters ranging from 400nm to $4{\mu}m$ were photo-induced after plasma formation occurred upon irradiation with peak intensities of more than $1{\times}1013W/cm^2$. The graded refractive index profile was fabricated to be a symmetric around from the center of the point at which low-density plasma occurred. The maximum refractive index change was estimated to be $1.5{\times}10^{-2}$. The two optical embedded gratings in BK-7 glass plate were demonstrated with refractive index modification induced by the scanning of low-density plasma formation.

• Journal of Electrical Engineering and Technology
• /
• 제10권4호
• /
• pp.1804-1814
• /
• 2015

In order to explore the characteristics of electrons in DC negative corona discharge, an improved plasma chemical model is presented for the simulation of bar-plate DC corona discharge in dry air. The model is based on plasma hydrodynamics and chemical models in which 12 species are considered. In addition, the photoionization and secondary electron emission effect are also incorporated within the model as well. Based on this model, electron mean energy distribution (EMED), electron density distribution (EDD), generation and dissipation rates of electron at 6 typical time points during a pulse are discussed emphatically. The obtained results show that, the maximum of electron mean energy (EME) appears in field ionization layer which moves towards the anode as time progresses, and its value decreases gradually. Within a pulse process, the electron density (ED) in cathode sheath almost keeps 0, and the maximum of ED appears in the outer layer of the cathode sheath. Among all reactions, R1 and R2 are regarded as the main process of electron proliferation, and R₂₂ plays a dominant role in the dissipation process of electron. The obtained results will provide valuable insights to the physical mechanism of negative corona discharge in air.