• Title/Summary/Keyword: plate bonding

검색결과 230건 처리시간 0.026초

탄성 의치상 이장재의 접착력에 관한 연구 (A STUDY ON THE BONDING STRENGTH OF RESILIENT DENTURE LINERS)

  • 이상훈;정재헌
    • 대한치과보철학회지
    • /
    • 제30권3호
    • /
    • pp.411-436
    • /
    • 1992
  • The purpose of this study was to assess the adhesion of resilient denture liners (such as, heat-cured silicone molloplast B,cold- cured silicone Mollosil) to polymethyl metacrylate (K-33) and metal (Megalloy) in the laboratory by peel test. The resilient denture lines were processed according to manufactures instruction, onto prepared specimens(original resin base plate, rough resin base plate, stippled metal plate, mesh metal plate ) 75mm long and 25m wide. And then, the peel test was performed by instron. The results were as follows : 1. The bonding strength of Mollosil was stronger than that of Molloplast B except the specimen of stippled metal plate. 2. The tensile strength of Mollosil was weaker than that of Molloplast Bas tearing of Mollosil was occured in the peel test. 3. Mesh metal plate had the highest bonding strength in the case of Molloplast B and Mollosil. But stippled metal plate have high bonding strength in the case of Molloplast B and have the lowest bonding strength in the case of Mollosil. 4. The bonding strength of rough resin base plate was stronger than that of original resin base plate in the case of Molloplast B and Mollosil. 5. The bonding strength of metal plates was stronger than that of resin base plates in the case of Molloplast B and Mollosil except the case of bonding strength between the stippled metal plate and Mollosil. 6. It seems that the Increase of surface and retention form of metal plate and resin base plate produces higher physical bonding strength.

  • PDF

접착 보강부재 단부에서의 응력분포에 관한 연구 (Studies on Stress Distribution at the end of the Bonded Strengtening Plate)

  • 김지선;김경원;한만엽;정영수;홍영균
    • 한국콘크리트학회:학술대회논문집
    • /
    • 한국콘크리트학회 1996년도 봄 학술발표회 논문집
    • /
    • pp.129-134
    • /
    • 1996
  • Bonding strength of reinforcing material has been recognized to be the most important factor which determines the strengthening effect and the durability of repair work. The properties of bonding layers affects the stress distribution at the end of the plate, therefore the behavior of bonding layer has to be investigated. In this study, the stress distribution at the end of the bonded plate has been tested and compared with Roberts' analysis. Shear stress and vertical normal stress at the end of strengtening plate are analysized and the effedts of bonding layer thickness, plate thickness and plate length on the bonding behavior are tested. The test results showed that thickness is one of the most important factor, which is the thinner the thickness, the smaller the maximum stress.

  • PDF

노치를 이용한 보강재의 부착력 증가 방안에 관한 연구 (A Study to Improve Bonding Strength of Strengthening Plate with Notches)

  • 한만엽;송병표;이광명
    • 콘크리트학회지
    • /
    • 제11권1호
    • /
    • pp.129-139
    • /
    • 1999
  • 본 연구는 콘크리트 구조물의 보강공법으로 널리 쓰이고 있는 강판에 의한 부착식 보강공법의 단점인 단부에서의 강판분리 현상에 대한 보완실험으로 실시되었다. 실험결과 노치가 적용된 강판부착식 공법이 항복하중 이후 최대하중까지의 증가율이 기존의 공법보다 증가되어 구조물의 보강 성능의 개선 및 안전성의 확보 측면에서 크게 개선되었을 뿐만 아니라 균열이나 처짐의 조절측면에서도 우수한 것으로 판명되었다. 이는 강판에 대한 약간의 변형만으로도 구조물의 수명을 연장시킬 수 있다는 장점과 함께 경제적으로도 보강된 구조물에 대한 추가적인 제반 비용의 절감도 기대할 수 있을 것이다.

Strength degradation of reinforced concrete piers wrapped with steel plates under local corrosion

  • Gao, Shengbin;Ni, Jie;Zhang, Daxu;Ge, Hanbin
    • Steel and Composite Structures
    • /
    • 제24권6호
    • /
    • pp.753-765
    • /
    • 2017
  • This paper aims to investigate the strength degradation of reinforced concrete piers wrapped with steel plates which corrode at the pier base by employing a three dimensional elasto-plastic finite element formulation. The prediction accuracy of the employed finite element analysis method is firstly verified by comparing the analytical results with test results. Then, a series of parametric studies is carried out to investigate the effects of steel plate's corrosion position along width direction, corrosion depth along plate thickness, corrosion range along width direction, and steel plate-concrete bonding degradation on the strength of the piers. It is observed that the strength degradation of the piers is closely related to steel plate's corrosion position, corrosion depth and corrosion range in the case of local corrosion on the webs. In contrast, when the base of flanges corrodes, the strength degradation of the piers is only related to steel plate's corrosion depth and corrosion range, and the influence of corrosion position on the strength degradation is very gentle. Furthermore, the strength of the piers decreases with the degradation of steel plate-concrete bonding behavior. Finally, the maximum strength of the piers obtained from numerical analysis corresponding to different bonding behavior is compared with theoretical results within an accepted error.

기판단위 밀봉 패키징을 위한 내압 동공열의 설계 및 강도 평가 (Design and Strength Evaluation of an Anodically Bonded Pressurized Cavity Array for Wafer-Level MEMS Packaging)

  • 강태구;조영호
    • 대한기계학회논문집A
    • /
    • 제25권1호
    • /
    • pp.11-15
    • /
    • 2001
  • We present the design and strength evaluation of an anodically bonded pressurized cavity array, based on the energy release rate measured from the anodically bonded plates of two dissimilar materials. From a theoretical analysis, a simple fracture mechanics model of the pressurized cavity array has been developed. The energy release rate (ERR) of the bonded cavity with an infinite bonding length has been derived in terms of cavity pressure, cavity size, bonding length, plate size and material properties. The ERR with a finite bonding length has been evaluated from the finite element analysis performed for varying cavity and plate sizes. It is found that, for an inter-cavity bonding length greater than the half of the cavity length, the bonding strength of cavity array approaches to that of the infinite plate. For a shorter bonding length, however, the bonding strength of the cavity array is monotonically decreased with the ratio of the bonding length to the cavity length. The critical ERR of 6.21J/㎡ has been measured from anodically bonded silicon-glass plates. A set of critical pressure curves has been generated for varying cavity array sizes, and a design method of the pressurized cavity array has been developed for the failure-free wafer-level packaging of MEMS devices.

Al-Si계 필러메탈을 이용한 A1050알루미늄의 브레이징 접합조건에 관한 연구 (A Study on the Brazing Bondinf Conditions of A1050 Using Al-Si Alloy Filler Metal)

  • 김정일;김영식
    • Journal of Advanced Marine Engineering and Technology
    • /
    • 제17권1호
    • /
    • pp.66-72
    • /
    • 1993
  • The brazing of Al to Al using Al-Si alloy filler metal was performed under different bonding conditions such as ratio of lap length to plate thickness, surface roughness and joint clearance of the lap joint. The adopted thickness of the base metal in this experiments were two kinds of 4mm and 7mm which were most commonly used in various field. Influence of several bonding conditions of Al/Al joint was quantitavely evaluated by bonding strength test, and microstructural analysis at the interlayer were performed by optical microscope. From above experiments, the optimum bonding conditions of the brazing bonding of Al/Al using Al-Si alloy filler metal was determined. The major results obtained are as follows. 1) The fracture occurs at brazed joint in the conditions of that the ratio of lap length to plate thickness is less than 2 in case of 7mm plate thickness. 2) The ratio of lap length to plate thickness which the fracture occurs at base metal is decreased with the decreasing of the plate thickness. 3) The joint strength is not affected by the surface roughness and joint clearance of the brazed part. 4) The heat-treatment of the brazed joint contribute to eliminate the boundary between the base metal and filler metal. However, the joint strength is not affected by the heat-treatment.

  • PDF

강판으로 보강된 RC보의 에폭시-콘크리트 계면의 부착특성 (Bonding Properties of Epoxy-Concrete Interface in RC Beams Strengthened by Steel Plate)

  • 박윤제;신동혁;이광명;신현목
    • 콘크리트학회논문집
    • /
    • 제13권3호
    • /
    • pp.221-227
    • /
    • 2001
  • 강판으로 철근콘크리트 보를 휨보강하면 보의 강성과 강도는 현저하게 증가하나 부착면에서의 조기파괴로 인하여 충분한 연성을 발휘하지 못하는 경우가 자주 발생한다. 본 연구에서는 에폭시와 콘크리트 계면에서의 부착파괴 메카니즘을 규명하기 위하여 Mohr-Coulomb 규준을 채택하였으며, 에폭시-콘크리트 계면의 부착특성을 결정하기 위하여 사전단 부착실험, 직접전단 부착실험 및 휨보강 부재실험을 수행하였다. 실험과 수치해석을 통하여 에폭시-콘크리트 계면의 내부마찰각이 45$^{\circ}$ 일 때 점착력은 50 kgf/$\textrm{cm}^2$~70 kgf/$\textrm{cm}^2$을 얻었으며, 이를 강판으로 보강된 RC보의 구조계산에 적용하여 파괴하중을 예측함으로써 보강보의 조기파괴를 효과적으로 방지할 수 있을 것으로 판단된다.

고온용 RFID 태그 패키징 및 접합 방법 (Bonding Method and Packaging of High Temperature RFID Tag)

  • 최은정;유대원;변종헌;주대근;성봉근;조병록
    • 한국통신학회논문지
    • /
    • 제35권1B호
    • /
    • pp.62-67
    • /
    • 2010
  • 본 연구는 다양한 산업 환경에 적용되는 RFID 태그 개발에 있어 RFID 태그 패키징 개발과 RFID 태그 플립칩(flip chip) 접합 방법이 산업 환경 맞춤형 RFID 태그 개발에 미치는 영향에 대해 분석하였다. RFID 태그 플립칩(flip chip) 접합은 와이어 접합(wire bonding), 초음파 접합(ultrasonic bonding), 열융착 접합(heat plate bonding), 레이저 접합(laser bonding)으로 구분되어 있으며, 이런 접합 방법은 다양한 RFID 태그 개발의 적용 환경에 따라 적합한 접합 방법이 있음을 본 연구를 통해서 알 수 있었다. 극고온, 극저온, 다습, 고내구성 등 다양한 산업 환경 중 극고온 환경에서의 RFID 태그 개발은 빛 에너지를 흡수하여 열 에너지로 전환하는 레이저 접합 방법과 직접적인 열 전달 방식인 열융착 접합 방법은 접속 재료인 ACF의 손상으로 인해 부적합하고, 와이어를 이용하여 직접 범프와 패턴을 연결하는 와이어 접합 방법이 적합함을 알 수 있었다.

접착공법에 의해 전단보강된 RC보의 전단강도 예측 (Shear Strength Prediction of RC Beams Strengthened by Externally Bonding Method)

  • 박성민;변근주;송하원
    • 한국콘크리트학회:학술대회논문집
    • /
    • 한국콘크리트학회 2001년도 봄 학술발표회 논문집
    • /
    • pp.69-74
    • /
    • 2001
  • Steel plate or fiber composite plate are mainly used in externally bonding method. Shear strengthening by externally bonding method is to confirm shear safety and to avoid brittle failure. In case of strengthening by externally bonding method, a failure of structure occurs frequently due to delamination between strengthening plate and concrete. Therefore, it is important to consider the delamination in the strengthening design. The objective of this study is to propose a modified shear strength evaluation by considering the delamination. The delamination criteria of strengthening plate is established by the ultimate strain and shear stress. And shear strength of RC beams is proposed in terms of the delamination criteria. The proposed shear strength is compared with test results and verified through the comparison.

  • PDF

Results of Delamination Tests of FRP- and Steel-Plate-Reinforced Larix Composite Timber

  • LEE, In-Hwan;SONG, Yo-Jin;SONG, Da-Bin;HONG, Soon-Il
    • Journal of the Korean Wood Science and Technology
    • /
    • 제47권5호
    • /
    • pp.655-662
    • /
    • 2019
  • This study evaluated the multi-bonding performances of timbers as well as those of reinforcement and timber to obtain data for preparing guidelines regarding the use of timbers as large structural members. For the multi-bonding performances of timbers, four types of bonding surfaces were prepared according to the pith position. For the bonding performances of FRP (fiber-reinforced plastic)/steel plate and timber, a total of 11 types of specimens were produced for the selection of the appropriate adhesive. The bonding performances of the produced specimens were evaluated through a water soaking delamination test, a water boiling delamination test, and a block shear strength test. The test results showed that the bonding strength of the bonding surface according to the pith position was highest in the specimen for which the two sections with the pith at the center of the cross-section on timber and between the bonding surfaces (the tangential and radial sections were mixed) were bonded. Furthermore, the specimens for which the section (radial section) with the pith on the bonding surface of the timber was bonded showed a high delamination percentage. The results of the block shear strength test showed that the bonding section did not have a significant effect on the shear strength, and that the measured wood failure percentage was higher than the KS standard value. The PVAc adhesive showed the highest bonding strength between larix timber and GFRP (glass FRP). Furthermore, the epoxy and polyurethane adhesives showed good bonding strength for CFRP (carbon FRP) and structure steel, respectively.