• Journal of the Korean Geotechnical Society
• /
• v.29 no.11
• /
• pp.73-84
• /
• 2013

When a slope failure or a debris flow occurs, a shear strength on failure plane becomes nearly zero and soil begins to flow like a non-cohesive liquid. A consistency of cohesive soils changes as a water content increases. Even a cohesive soil existing at liquid limit state has a small amount of shear strength. In this study, a water content, at which a shear strength of cohesive soils is zero and then cohesive soils will start to flow, was proposed. Three types of clays (kaolinite, bentonite and kaolinite (50%)+bentonite (50%)) were mixed with three different solutions (distilled water, sea water and microbial solution) at liquid limit state and then their water contents were increased step by step. Then, their undrained shear strength was measured using a portable vane shear device called Torvane. The ranges of undrained shear strength at liquid and plastic limits are 3.6-9.2 kPa and 24-45 kPa, respectively. On the other hand, the water content that corresponds to the value of the undrained shear strength changing most rapidly is called flow water content. The flow limit refers to the water content when undrained shear strength of cohesive soils is zero. In order to investigate the relationship between liquid limit and flow limit, the cohesive index was defined as a value of the difference between flow limit and liquid limit. The new plasticity index was defined as the value of difference between flow limit and plastic limit. The new liquidity index was also defined using flow limit. The values of flow limit are 1.5-2 times higher than those of liquid limit. At the same time, the values of new plasticity index are 2-5.5 times higher than those of original plasticity index.

• Transactions of Materials Processing
• /
• v.12 no.3
• /
• pp.228-235
• /
• 2003

In this paper, the workability of flange in the radial extrusion is analyzed in terms of the deformation pattern, the punch load and the forming limit by using simulation and experiment. A single action pressing is applied to both simulation and experiment. The analysis in this study is focused on the transient extrusion into the gap in radial direction with various gap heights and die corner radius. Based on the surface strains where surface cracking occurs, the forming patterns and strain-fracture relationships in producing radially extruded flange are obtained.

• Journal of Navigation and Port Research
• /
• v.36 no.3
• /
• pp.181-187
• /
• 2012

Highly plastic clays in their normally consolidated states are not always linear but are concave downwards. Thus their compression index deceases with the increase of consolidation pressure. The $e-{\log}{\sigma}_{\upsilon}{\prime}$ curves of plastic or non-plastic silty clays are not linear but are convex upwards. In this paper, consolidation tests were conducted with several undisturbed field soils of Korea south coast and their $e-{\log}{\sigma}_{\upsilon}{\prime}$ plots are not always linear. In case of using Butterfield's method(liquid limit 50~100%), ${\ln}{\upsilon}-{\ln}{\sigma}_{\upsilon}{\prime}$ plots are linear. But some undisturbed samples which have void ratio over 2.24, liquid limit over 100% and plasticity index over 60% are not linear. In results of consolidation tests with remolded samples which contain silt(fly ash) contents of 90% has compression index increasing with the increase in consolidation pressure.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 1993.10a
• /
• pp.131-138
• /
• 1993

To analysis machanical behavior for RC frame under monotonic & Cyclic load, it is needed to investigate elasto-plastic behavior for steel & concrete. Therefore, in this study, we idealized material model(steel and concrete) to take into account elasto-plastic, limit state, and developed structural analysis program that consider complex non-linearity. We investigated simple beam and portal frame under cyclic & monotonic loading, so we confirmed the propriety.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.9
• /
• pp.1293-1298
• /
• 2010

In most power plants, wall thinning in carbon-steel pipes due to flow-accelerated corrosion is one of the major aging phenomena, and it reduces the load-carrying capacity of the piping system. Various types of wall-thinning defects were manufactured in real-scale elbows, and monotonic in-plane bending tests were performed under internal pressure to evaluate the failure behavior of the elbows. In this paper, the behavior of elastic and plastic limit leads of locally thinned elbows in a real-scale failure test is presented. The loads determined on the basis of TES (twice elastic slope) were considered to be the limit loads of locally thinned elbows so that the integrity of the thinned elbows could be maintained, even when a small amount of plastic deformation might have occurred.

• Geomechanics and Engineering
• /
• v.39 no.1
• /
• pp.1-11
• /
• 2024

Geotechnical parameter estimation is critical to the design, performance, safety, and cost and schedule management in Tunnel Boring Machine projects. Since these parameters vary within a certain range, relying on mean values for evaluation introduces significant risks to the project. Due to the non-homogeneous characteristics of geological formation, data may not exhibit a normal distribution and the presence of outliers might be deceptive. Therefore, the use of reliable analyses and simulation models is inevitable in the course of the data evaluation process. Advanced modeling techniques enable comprehensive analysis of the project data and allowing to model the uncertainty in geotechnical parameters. This study involves using Monte Carlo Simulation method to predict probabilistic distributions of field data, and therefore, establish a basis for designs and in turn to minimize project risks. In the study, 166 sets of geotechnical data Obtained from 35 boreholes including Standard Penetration Test, Limit Pressure, Liquid Limit, and Plastic Limit values, which are mostly utilized parameters in estimating project requirements, were used to estimate the geotechnical data distribution of the study field. In this context, firstly, the data was subjected to multi-parameter linear regression and variance analysis. Then, the obtained equations were implemented into a Monte Carlo Simulation, and probabilistic distributions of the geotechnical data of the field were simulated and corresponding to the 90% probability range, along with the minimum and maximum values at the 5% probability levels presented. Accordingly, while the average SPT N30 value is 42.86, but the highest occurrence rate is 50.81. For Net Limit Pressure, the average field data is 17.07 kg/cm², with the maximum occurrence between 9.6 kg/cm² and 13.7 kg/cm². Similarly, the average Plastic Limit value is 22.32, while the most probable value is 20.6. The average Liquid Limit value is 56.73, with the highest probability at 54.48, as indicated in the statistical data distribution. Understanding the percentage distribution of data likely to be encountered in the project allows for accurate forecasting of both high and low probability scenarios, offering a significant advantage, particularly in ordering TBM requirements.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.6
• /
• pp.68-79
• /
• 2018

An examination of the characteristics of the ground material in is very important in a ground investigation. Casagrande classified soil using the material properties of soils. The liquid-plastic limit test is useful for obtaining basic information of soil, and is an effective method for classifying silt and clay, as well as the material properties, such as shear strength, shrinkage, and expansion. Unlike the liquid limit test, the plasticity limit test is due to the ambiguity of the test procedure. Many geotechnical engineers and scholars have questioned the test results. In this study, a new plasticity limit method was used to compare with the thread rolling method with kaolinite, ilite and bentonite at a certain ratio, and samples were collected from the west coast of Korea. As a result of the comparison, the test value of the new test method showed high reproducibility because the error range of the test value of the conventional thread rolling test was only 10% but the error range of the new test values decreased to 2%. The difference in the slope of the existing plasticity test values was 0.1519 ~ 0.1925, and the results of the test were similar or coincided with each other. Aone - point method was proposed to make it easier to apply the new test method.

• Journal of the Korean Geotechnical Society
• /
• v.28 no.10
• /
• pp.79-88
• /
• 2012

Small amount of salt and various microorganisms are contained in natural soils or clays near the shore. In this study, most common clay minerals such as kaolinite and bentonite are used to evaluate the effect of salt and microorganism on liquid and plastic limits. The effect of time after mixing clays with water was also investigated for the consistency limits of clays. The test was conducted immediately, 1 day, or 7 days after mixing soils. For liquid limit tests two different test methods were used, the percussion cup method by Casagrande and the fall cone method. When sea water or microbial solution was used for mixing soils rather than distilled water, the liquid limit of kaolinite decreased by 6-15% and that of bentonite further decreased up to 37-53%. The liquid limit obtained from the fall cone method was approximately 10% for bentonite and 20% for kaolinite, which are higher than those from the percussion cup method. The effect of time on liquid and plastic limits was significant for those tested immediately or 1 day later but the values obtained after 1 day or 7 days did not vary a lot, regardless of soils, mixing waters or test methods.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.10a
• /
• pp.156-159
• /
• 2004

Most formulations for a forming limit diagram (FLD) have been based on yield stress potentials defined in the stress field. Nevertheless, there are formulations where potentials defined in the stain-rate field are especially convenient to formulate the rigid plastic material. Based on a strain-rate potential proposed for materials exhibiting planar anisotropic, the formulations for the forming limit diagram has been developed applying M-K theory. As verification example, the formulation is applied for anisotropic AA5182-O sheet. The good verification results show that the formulation for the forming limit diagram has been successfully developed.

• Advances in Computational Design
• /
• v.8 no.3
• /
• pp.191-217
• /
• 2023

The objective of this study was to evaluate the foundation structure of a 3.6-MW wind turbine generator (WTG) installed offshore in Western Korea. The ultimate limit state (ULS) and fatigue limit state (FLS) of the multi-pile steel foundation (MSF) installed at the Saemangeum offshore wind farm were structurally investigated using the finite element (FE) software, ANSYS Workbench 19.0. According to the ULS analysis, no plastic deformation was found in any of the components constituting the substructure. At the same time, the maximal stress value reached the calculation limit of 335 MPa. According to the FLS results, the stress concentration factor (SCF) ranged from 1.00 to 1.88 in all components. The results of this study can be applied to determine the optimal design for MSFs.