• Journal of the Korean Society of Marine Environment & Safety
• /
• v.29 no.5
• /
• pp.488-496
• /
• 2023

Ship and bridge structures are a type of long box-shaped structure, and resistance to vertical bending moment is a key factor in their structural design. In particular, because box girders are repeatedly exposed to irregular wave loads for a long time, the continuous collapse behavior of structural members must be accurately predicted. In this study, plastic collapse behavior, including buckling according to load changes of the box girder receiving pure bending moments, was analyzed using a numerical analysis method. The analysis targets were selected as three box girders used in the Gordo experiment. The cause of the difference was considered by comparing the results of the structural strength experiment with those of non-linear finite element analysis. This study proposed a combination of the entire and local sagging shape to reflect the effect of the initial sagging caused by welding heat that is inevitably used to manufacture carbon steel materials. The procedures reviewed in the study and the contents of the initial sagging configuration can be used as a good guide for analyzing the final strength of similar structures in the future.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.30 no.4
• /
• pp.358-364
• /
• 2024

Type A carrier structures that support blocks or equipment gradually deform over time with load changes, reducing the area in contact with the block and changing the load pattern from distributed to concentrated during construction work in the shipyard. This phenomenon has the potential to misrepresent actual service loads. In particular, A carriers are often used by small manufacturers, who often do not have specialized engineering capabilities, necessitating the development of a method for easy calculation of carrier safe working load. This study proposes a quick evaluation method for the long-term safe working load of Type A carriers, to predict the plastic deformation and safety issues resulting from changes in load distribution. Based on the results of finite element analysis (beam and shell modeling) of the centralized load, beam-theory was modified to propose a method for determining the distributed load conditions of the A-carrier. In beam modeling, the theoretical value was multiplied by a correction factor of 0.73 for concentrated loads and 0.69 for distributed loads to obtain a safe working load. For shell modeling, a correction factor of 0.75 can be used for concentrated loads and 0.69 for distributed loads. This study can serve as a basis for improving the safety of shipbuilding, enabling quick and effective decisions for determining safe working loads in actual working environments.

• Korean Journal of Soil Science and Fertilizer
• /
• v.38 no.1
• /
• pp.38-44
• /
• 2005

In addition to the variation in nitrate accumulation of vegetables due to environmental conditions, there is also a distinct genetic variation. The variation of nitrate accumulation in some cultivars of lettuce and spinach commonly cultivated in Korea was investigated. Ten cultivars for both lettuce and spinach were grown in plastic containers filled with a 1:1 mixture of perlite and vermiculite with application of Hoagland No. 2 nutrient solution of high nitrate content (17.3 mM N) in a greenhouse condition. Plants were harvested four weeks after transplanting four-leaf stage seedlings. Plant growth was measured by fresh and dry matter of shoot, and contents of nitrate and other inorganic ions and organic solutes including sugar, amino acids and organic acids were measured. Large and significant genotypical variations in the nitrate content of the plants were found for both lettuce and spinach, and high negative correlations between nitrate content and fresh or dry weight were found in lettuce and spinach. Variation in nitrate accumulation of lettuce and spinach cultivars was not directly related to the differences in contents of organic and inorganic solutes, and this result indicates that photosynthesis and osmotic regulation are not directly related with the nitrate accumulation. Considering the correlations between nitrate content and plant growth of this study, it can be simply suggested that different cultivars of lettuce and spinach have their own inherited growth and physiological characteristics and also optimum nitrogen level required for the growth. Therefore when available nitrogen in root media is higher than the optimum level required for the inherited growth potential, some of the excess nitrate supplied can be accumulated in plants.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.17 no.1
• /
• pp.43-54
• /
• 1989

In recent years plants have increasingly become in inferior part of the interior designing of large buildings. In 28 large buildings selected at random in Seoul City have been subjected to studies on utilization status of fille interior landscape plants. The results obtained were as follows. 1. Plant class found in Interior of large buildings were 59 class, especially Dracaena were the most predominent plants among them, and then comes Monstera, Phiodendron, Schefflera, and Washingtonia in that order. 2. The most abundant ornamental plant cultivars were Monstera adansoii(Monstera perutusa cv.), and then comes Schefflera arboricora(Schefflera Hong Kong cv.), Washingionia rubusta (Washingtonia palm). Rhapis excelsa, and Diffenbachia(Hawaii Snow cv.) in that order. 3. Foliage plants among the interior landscape plants showed 99.5 percent and Woody plants and Bonsai plants showed each 0.4, 0.1 percent. 4. Climbing foliage plants found in 28 large building observed For the present study were 9 cultivar, and the most abundant plants were Hedera (pittsburgh cv.) and Epipremnum (Marble Queen cv.) pl anted to clustered planting. 5. A majority of plants used to plastic pot, and most of 71an1s place on the floor. 6. Height of plants ranging less then 50cm were more frequently found, but ranging from 50cm to 2.0m were 4.3 percent and the most predominent height of plants were Canariensis showed 4m in the large buildings. 7. Interior light intensity in large building were shortage, therefore artificial lamp for formal growing needed to be equipped. 8. Purpose growth of interior plants were to in order visitors. 9. 7he superintendents prefered to used pot-stand. 10. The most important environment factor for plant growing were light, humidity, and water.

• Journal of Bio-Environment Control
• /
• v.29 no.2
• /
• pp.130-140
• /
• 2020

This study was conducted in order to closely examine about optimum shading for superior seedling production a container seedling of Tetradium daniellii, which is being increased the demand for a seedling due to being used for alternative energy, ecological restoration and honey plant. The experiment of investigating the optimum shading on T. daniellii was carried out by using plastic container types (350 ml/cavity) for the forestry facility cultivation. The shading level was treated with full sunlight and with 35%, 55%, 75% of the full sunlight. As a result of having surveyed height and root collar diameter growth of a containerized seedling in T. daniellii, a case of the shading experiment showed a noticeably high value was indicated in the full sunlight. It was surveyed that the stronger shading level leads to the lower growth value. Root development was most active in full sunlight. Dry matter production, it was investigated to be the highest in full sunlight. It was surveyed to be the similar tendency to the outcome of height and root collar diameter growth. QI, which is index of showing the quality of a seedling, stood at 0.98 in full sunlight, thereby having been investigated to be the highest. As for the chlorophyll content in a seedling, the highest chlorophyll content was indicated in the 75% shading treatment with the relatively highest shading level. The photosynthetic rate and the water use efficiency were surveyed to be the highest in full sunlight with 8.48 μmolCO₂·m^-2s^-1, 1.40 μmolCO₂·mmolm^-1H₂O, respectively. As a result of surveying the whole experiment, optimum shading level for superior seedling production a container seedling of T. daniellii is determined in full sunlight (0%). It is expected that this will be used as a basic data for mass production.

• The Journal of Natural Sciences
• /
• v.14 no.1
• /
• pp.139-149
• /
• 2004

It was aimed to find out an efficient method of drying hot pepper, of which powder is used as one of the main ingredients in Korean dish preparation including Kimchi. Before sun or heat drying fruits harvested were horizontally cut into three pieces punched with an auger of 4 mm in diameter, or used as the whole fruit. Various drying methods were used including sun drying, drying under a plastic house, sun drying after heat drying for 5 hours at $70^{\circ}C$, $80^{\circ}C$, or $90^{\circ}C$, heat drying only at $50^{\circ}C$, $60^{\circ}C$, or $70^{\circ}C$, and changing temperature of $70^{\circ}C$, $5hours+60^{\circ}C$ until coplete dry, $80^{\circ}C+60^{\circ}C$, or $90^{\circ}C+60^{\circ}C$. The results are summarized as follows. With sun drying of the whole fruit, in required about 10days to reach the satisfactory level of dryness as indicated by its moisture content of below 10% in general. In case of heat drying combined with sun drying, it required 5 to 7 days. For cut fruits, it required 1 or 2 days less than for whole or pinholed fruits until drying. Under heat of alternation temperature drying, cut fruits also dried 15-20 hours earlier compared with whole of pinholed fruits. There were not significant differences for the recovery rate of the fruit with various drying methods. The occurrence of white fruits, which are caused by one of physiological disorders during drying, and rotten fruits was reduced with the cut fruit drying. The damages were very high with the PE house drying, but very little with the heat drying.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.28 no.6
• /
• pp.256-268
• /
• 2016

This article reviews the papers published in the Korean Journal of Air-Conditioning and Refrigeration Engineering during 2015. It is intended to understand the status of current research in the areas of heating, cooling, ventilation, sanitation, and indoor environments of buildings and plant facilities. Conclusions are as follows. (1) The research works on the thermal and fluid engineering were carried out in the areas of flow, heat and mass transfer, cooling and heating, and air-conditioning, the renewable energy system and the flow inside building rooms. Research issues dealing with air-conditioning machines and fire and exhausting smoke were reduced. CFD seems to be spreading to more research areas. (2) Research works on heat transfer area were carried out in the categories of heat transfer characteristics, pool boiling and condensing heat transfer and industrial heat exchangers. Researches on heat transfer characteristics included the economic analysis of GHG emission, micro channel heat exchanger, effect of rib angle on thermal performance, the airside performance of fin-and-tube heat exchangers, theoretical analysis of a rotary heat exchanger, heat exchanger in a cryogenic environment, the performance of a cross-flow-type, indirect evaporative cooler made of paper/plastic film. In the area of pool boiling and condensing, the bubble jet loop heat pipe was studied. In the area of industrial heat exchangers, researches were performed on fin-tube heat exchanger, KSTAR PFC and vacuum vessel at baking phase, the performance of small-sized dehumidification rotor, design of gas-injection port of an asymmetric scroll compressor, effect of slot discharge-angle change on exhaust efficiency of range hood system with air curtain. (3) In the field of refrigeration, various studies were carried in the categories of refrigeration cycle, alternative refrigeration/energy system, system control. In the refrigeration cycle category, a cold-climate heat pump system, $CO_2$ cascade systems, ejector cycles and a PCM-based continuous heating system were investigated. In the alternative refrigeration/energy system category, a polymer adsorption heat pump, an alcohol absorption heat pump and a desiccant-based hybrid refrigeration system were investigated. In the system control category, turbo-refrigerator capacity controls and an absorption chiller fault diagnostics were investigated. (4) In building mechanical system research fields, eighteen studies were reported for achieving effective design of the mechanical systems, and also for maximizing the energy efficiency of buildings. The topics of the studies included energy performance, HVAC system, ventilation, and renewable energies, piping in the buildings. Proposed designs, performance tests using numerical methods and experiments provide useful information and key data which can improve the energy efficiency of the buildings. (5) The field of architectural environment was mostly focused on indoor environment and building energy. The main researches of indoor environment were related to the user and location awareness technology applied dimming lighting control system, the lighting performance evaluation for light-shelves, the improvement evaluation of air quality through analysis of ventilation efficiency and the evaluation of airtightness of sliding and LS window systems. The subjects of building energy were worked on the energy saving estimation of existing buildings, the developing model to predict heating energy usage in domestic city area and the performance evaluation of cooling applied with economizer control. The studies were also performed related to the experimental measurement of weight variation and thermal conductivity in polyurethane foam, the development of flame spread prevention system for sandwich panels, the utilization of heat from waste-incineration facility in large-scale horticultural facilities.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.21 no.1
• /
• pp.31-48
• /
• 2019

The artificial ground freezing (AGF) method is a groundwater cutoff and/or ground reinforcement method suitable for constructing underground structures in soft ground and urban areas. The AGF method conducts a freezing process by employing a refrigerant circulating through a set of embedded freezing pipes to form frozen walls serving as excavation supports and/or cutoff walls. However, thermal expansion of the pore water during freezing may cause excessive deformation of the ground. On the other hand, as the frozen soil is thawed after completion of the construction, mechanical characteristics of the thawed soil are changed due to the plastic deformation of the ground and the rearrangement of soil fabric. This paper performed a field experiment to evaluate the freezing rate of marine clay in the application of the AGF method. The field experiment was carried out by circulating liquid nitrogen, which is a cryogenic refrigerant, through one freezing pipe installed at a depth of 3.2 m in the ground. Also, a piezo-cone penetration test (CPTu) and a lateral load test (LLT) were performed on the marine clay before and after application of the AGF method to evaluate a change in strength and stiffness of it, which was induced by freezing-thawing. The experimental results indicate that about 11.9 tons of liquid nitrogen were consumed for 3.5 days to form a cylindrical frozen body with a volume of about $2.12m^3$. In addition, the strength and stiffness of the ground were reduced by 48.5% and 22.7%, respectively, after a freezing-thawing cycle.