• International Journal of Control, Automation, and Systems
• /
• v.4 no.3
• /
• pp.359-364
• /
• 2006

This article describes the useful way to measure the torque and RPM of the geared motor. For this we have made the planetary geared reduction motor including 2 Hall sensors in it and the monitoring system. The monitoring system displays the sensing values (torque, rpm) and the calculated value (power) and it also has the network capability using the Bluetooth protocol. We will show that our solution is much more inexpensive and simple method to measure torque and rpm than before.

• 제어로봇시스템학회:학술대회논문집
• /
• 2005.06a
• /
• pp.2058-2062
• /
• 2005

This article describes the useful way to measure the torque and RPM of the geared motor. For this, we have made the planetary geared reduction motor including the torque sensor unit which consists of hall effects sensor and permanent magnet. Our monitoring system displays the sensing values (torque, rpm) and the calculated value (power) and it also has the network capability using the Bluetooth protocol. We will show that our solution is much more inexpensive and simple method to measure torque and rpm than before.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.26 no.5
• /
• pp.559-566
• /
• 2016

This study shows a development procedure and results of noise reduction for a new developed FF 8th speed automatic transmission. Based on planetary gear operating frequency analysis using PTA(planetary transmission analysis) program developed in 2012, It is expected that gear noise of the rear planetary gear set could be recognized easily in the concept design stage. Therefore, pRMC (planetary run many cases) analysis program that is developed in 2012 was applied to minimize the planetary gear noise level and noise distributions versus torque. To minimize noises coming from oil pump and final gears of a new transmission, several changes were applied, such as changing the clearance of double angular ball bearing, the oil pump rotor tooth number from 9 to 11 and the oil pump type from parachoid to megafloid and so on. Besides, stiffness values of the transmission case and the mount bracket were measured and reinforced properly. Finally, The total noise of the new FF 8th speed automatic transmission was developed successfully. Furthermore, E.O.L. testers also have been adapted to control the noise quality of automatic transmission assembly in the manufacturing factory. This paper could provide practical solutions to the automatic transmission NVH problems.

• Journal of the Korean Institute of Gas
• /
• v.26 no.2
• /
• pp.21-26
• /
• 2022

Since the four-wheel drive transmits the driving force to all four wheels, the traction with the road surface increases, thereby increasing the driving force. However, it has the disadvantage of lowering fuel efficiency. Therefore, four-wheel drive is commonly used as a method of converting to optional four-wheel drive when necessary while driving in two-wheel drive. This selective four-wheel drive converts the driving force by mechanically changing the electric signal sent by the driver in the transfer case. In this study, in order to mechanically change the electrical signal, a reducer is applied to the motor to increase the torque to perform the function. Therefore, in this study, a reduction mechanism applicable to the motor inside the transfer case applied to convert the drive is derived, and the reduction ratio applying the planetary gear type is optimized accordingly. And based on the derived reduction ratio, two sets of planetary gears using a ring gear in common were applied to develop a planetary gear tooth type in which the input shaft and output shaft are decelerated in the same phase. Optimization design was carried out.

• Proceedings of the Korean Institute of Intelligent Systems Conference
• /
• 2004.10a
• /
• pp.201-204
• /
• 2004

감속기가 사용되어지는 경우 부하의 변동이나 구동부의 상태변화에 따라 모터의 토크, 회전수 등이 변하는데 이러한 값들을 모니터링 하면 부하의 변동이나 구동부를 진단할 수 있다. 본 논문은 유성기어를 이용한 기어드 모터를 제작하고, LCD를 포함하는 간단한 사용자 인터페이스를 통해 전달 Torque, 전달회전수(rpm), 전달동력을 확인할 수 있는 소형의 표시기가 있는 감속기에 관한 것이다. 일반적으로 전달 토크를 측정하는 장비는 크기가 크고 고가이며 계측기를 연결하고 측정하는 과정이 매우 번거로울 뿐만 아니라 지속적인 유지보수가 필요한 단점이 있다. 본 논문에서 제안하는 유성기어를 사용하면 간단히 모터의 토크 및 회전수를 측정할 수 있고 측정값을 표시하는 표시기를 모터에 부착할 수 있다. 측정 및 표시기는 기존 가격에 비해 매우 값싸게 제작할 수 있고 유지보수가 필요 없으며 검출 값을 시스템 제어부에 피드백 시키면 자기진단이 가능해진다. 특히 블루투스를 이용한 무선 통신기능을 부과하면 원격 모니터링이 가능하고 복수 모터유닛의 네트워크 구성이 용이하며 인터넷을 통한 데이터 통신으로의 확장이 가능하다.

• Journal of the Korean Society for Precision Engineering
• /
• v.30 no.11
• /
• pp.1187-1192
• /
• 2013

In the case of 4 wheel drive (4-WD) type car, power switching occurs to 4-WD by operating lever or switch that operates power switching device attached in transfer case which can operate motor by electric signal. So if the RPM of motor is high, power switching will not exactly occur and can cause damage to gear in transfer case according to circumstances. So in this study, we applied 2 level of planet gear type motor spindle of motor drive part of a power train. And conducted decelerating to increase torque to switch power safe and accurately. Also, we researched efficiency of gear by designing reduction gear ratio and gear type and by calculating contact stress and bending strength. Based on researched content, we made drive head of power switching device and a reduction module which uses type that uses motor spindle as sun gear and ring gear as cover.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.5
• /
• pp.537-543
• /
• 2012

In this study, we experimentally investigate a noise mechanism related to the machining accuracy of the reducer in the driving state. We fabricate a planetary reducer and four types of gears for use in the planetary reducer. We use signal analysis to determine the noise and vibration of the reducer at different motor speeds; the motor speed is increased from 0 rpm to the maximum speed in a stepwise manner. In addition, we obtain the sound level by using a sound level meter. The machining accuracy of gears is evaluated by public organizations, Korea Testing Laboratory (KTL), on the basis of the Japanese Industrial Standard (JIS). We analyze and compare the results with the noise and vibration of the reducer.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.14 no.7
• /
• pp.914-919
• /
• 2004

When the motor is rotating, the torque and rpm are varying as the loads or the driving status connecting through reduction units are changing. On the contrary, one can monitor the changes of the loads or the driving status in the manner of measuring motor torque and rpm. There is a torque measuring method using the strain gauge and bridge circuit. But, because this is the contact method, it has the life time which is dependent on rotating velocity and used time. So this system demands on replacement of some Parts or whole system itself for maintenance. And this system is also relatively big and expensive, requiring preceding annoying process. In this paper, we are going to suppose non-contact method to measure torque and rpm using the Hall effects sensor For this we have made the planetary geared reduction motor with Hall sensors and with the monitoring system. The monitoring system displays the sensing data(torque, rpm) and calculated data( power) and also has the network capability with Bluetooth protocol. Our solution is much more inexpensive ;md simple method to measure torque and rpm than before.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.25 no.6
• /
• pp.391-398
• /
• 2015

The swing noise of an excavator is reduced in this study. When an excavator is under a swing motion, it produces the annoying noise which is required to be reduced. To identify the characteristics of the swing noise, the signals of noise and vibration from an excavator are measured during the swing motion. From the variation of the driving motor speed, the noise and vibration signals are picked up and plotted in the waterfall plots. From the waterfall plots, we identify the frequency components corresponding to the driving motor frequency, the gear mesh frequency of the planetary gear, and their harmonics. In addition, the natural frequencies and modes of the center frame are extracted by using the experimental modal test. It is found that the swing noise is amplified when the gear mesh frequencies coincide with the natural frequencies of the center frame. To reduce the swing noise, the structural modification is performed to the center frame. Finally, it is observed that the noise is considerably reduced by the structural modification.