• Water for future
• /
• v.14 no.4
• /
• pp.73-81
• /
• 1981

More than 650 numbers of water well ranging in depth from 100M to 200M were installed in South Korean Penninsula during the last decade for the purpose of industrial use and municipal water supply. Those data were compiled and synthesized by writer to determine their hydrogeologic occurences in accordance with their geologic and areal characteristics. Rocks yielding the deep seated ground water beared in the geologic primary and secondary porosities are classified into 6 groups according to their geologic, hydrogeologic, and topographic characteristics, that are: volcanic, sedimentary, meta-sediment and/or schist, andesitic, gneissic, and granitic rocks. The order of ground water productivity of the groups is as written above. Even granitic rocks including porphyries, granite, and intermediate and basic plutonic rocks is considered to be the most poorest ground water yielding group among 6, it's average yield form a single well with average drilling depth of 116M is about 225 cubic meters per day if it's drilling site is properly located. Generally speaking, seizable geologic structures such as fractured, sheared, and faulted zone at the flat surface and valley center yield almost 310% more of deep seated bet rock ground water in comparision with minor structures of joints, bedding planes, and so on that are occured at high land. 50 numbers of water well drilled at crystalline rocks were specially checked and measured it's ground water yie 1ds at each drilled depth to determine each interval's productivity while hammer drilling was going on. The results indicate that the specific capacity and yield of each water well at a depth below 70M to 80M was almost neglegible. It means that optimum well depth of crystalline rocks, except the area having seizable geologic structures, shall be not deeper than 80M.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.15 no.4
• /
• pp.301-307
• /
• 2002

Direct bonded SOI wafer pairs with $Si ll SiO_2/Si_3N_4 ll Si$ the heterogeneous insulating layers of SiO$_2$-Si$_3$N$_4$are able to apply to the micropumps and MEMS applications. Direct bonding should be executed at low temperature to avoid the warpage of the wafer pairs and inter-diffusion of materials at the interface. 10 cm diameter 2000 ${\AA}-SiO_2/Si(100}$ and 560 $\AA$- ${\AA}-Si_3N_4/Si(100}$ wafers were prepared, and wet cleaned to activate the surface as hydrophilic and hydrophobic states, respectively. Cleaned wafers were pre- mated with facing the mirror planes by a specially designed aligner in class-100 clean room immediately. We employed a heat treatment equipment so called fast linear annealing(FLA) with a halogen lamp to enhance the bonding of pre mated wafers We kept the scan velocity of 0.08 mm/sec, which implied bonding process time of 125 sec/wafer pairs, by varying the heat input at the range of 320~550 W. We measured the bonding area by using the infrared camera and the bonding strength by the razor blade clack opening method, respective1y. It was confirmed that the bonding area was between 80% and to 95% as FLA heat input increased. The bonding strength became the equal of $1000^{\circ}C$ heat treated $Si ll SiO_2/Si_3N_4 ll Si$ pair by an electric furnace. Bonding strength increased to 2500 mJ/$\textrm{m}^2$as heat input increased, which is identical value of annealing at $1000^{\circ}C$-2 hr with an electric furnace. Our results implies that we obtained the enough bonding strength using the FLA, in less process time of 125 seconds and at lowed annealing temperature of $400^{\circ}C$, comparing with the conventional electric furnace annealing.

• Archives of design research
• /
• v.17 no.4
• /
• pp.141-148
• /
• 2004

The purpose of this study is to define the emotion that expressed in step animation and to quantify the intuitional expression of emotion that related step for using extract, measure, analysis the stimulate element about step. The survey of relation with 27 word of emotional expressions and 36 moving pictures of step sample is used for method of this test. The emotional mental structure is transferred to 2 dimensional planes as applying the results of analysis of integrated data using Quantification Method 3, which the integrated data is composed two axial - confidential axial and stabling axial. Analysis of distribution of 2 dimensional diagram shows that the second of the plane and the third of the plane have much data. However, the first of the plane and the forth of the plane have a little data. Through this kind of analysis of graph, it is difficult to express a different emotion between unstable the timidity mind and stable feel the timidity mind using only step analysis. Six difference types about physical elements affecting to emotion are selected and analyzed such as the paces of step, the rate of step, the movement angle of pelvis, the swing range of arm, angle of backbone and the lean angle of body. The result is that the rate of stop and the lean angle of body are the major element that effects to emotional stimulate of stop. This thesis argues about methods transforming subjective expression to objective and quantitative expression with the state of delicate emotion of character apply to step animation naturally. Those data to apply to multi-contents in future are the main target in this study.

• The Journal of Korean Academy of Prosthodontics
• /
• v.32 no.4
• /
• pp.526-552
• /
• 1994

The extent and direction of movement of removable partial dentures during function are influenced by the nature of the supporting structures and and the design of the prosthesis. Since forces are transmitted to the abutment teeth through occlusal rests, guide planes and direct retainers during functional movements, proper design based on the avaialble research data will maintain the health of abutment teeth and their supporting structures. The purpose of this in vitro study is evaluating stress distribution clinically around the abutment teeth prepared following 4-type clasping systems for unilateral free-end removable partial dentures. Three-Dimensional Photoelastic Stress Analysis method was used because it shows a visual display of stresses of the simulated abutment teeth and residual ridges and reveals stress concentration that can be read at any given points in terms of direction and magnitude. For this study, the author fabricated 4 mandibular photoelastic epoxy models missing left 1st and End molar. Epoxy models were duplicated and 4 unilateral removable partial dentures were construe- ted in accordance with 4-type direct retainers. Unilateral free-end removable partial dentures were positioned on their own models. 6kg force was loaded on the every removable partial dentures of the epoxy model on the central fossa of mandibular left 1st molar vertically by the loading device. After the stress was frozen in a stress freezing furnace, 6 specimens of 6-mm thickness were made from every epoxy model and examined with the circular polariscope. The results were as follows : 1. Generally I-bar clasp revealed the most favorable stress distribution around the abutment teeth. 2. At the end portion of the free-end ridge, Back action clasp showed the highest stress concentration at the bucco-lingual and top portions of the residual alveolar ridge. 3. At the distal area of the abutment teeth, Akers clasp and Roach clasp showed higher stress concentration bucco-lingually and apically than the others. 4. To the abutment tooth, I-bar clasp showed the least stress distribution bucco-lingually but the others showed irregular stress distribution. 5. At the mesial area of the abutment teeth, the order of effective stress distribution was I-bar clasp, Back-action clasp, Akers clasp and Roach clasp. There was big difference of stress distribution between them. 6. At the right 2nd premolar and 1st molar, the stress concentration of Akers clasp was a little high but that of I-bar clasp was low.

• Journal of Biomedical Engineering Research
• /
• v.24 no.4
• /
• pp.241-246
• /
• 2003

To evaluate the usefulness if functional MR imaging(MRI) for the determination of language dominance system and to assess differences in the visual and auditory instrument language generation task according to activation task or activated area. Functional maps of the language area were obtained during visual and auditory instructions in word generation tasks in 6 healthy volunteer with right-handness were examined on a 1.5T scanner and the EPI BOLD technique, and three pulse sequence technique get of the true axial planes. Both task consisted of 96 phases including 6 activations and rests contents. Postprocessing were done on MRDx program by using cross correlation method. Two task compare the blain activation area surveyed of 1anguage lateralization index. To evaluated of the detection rates of Broca. Wernicke, pre-frontal lobe, Supplementary Motor Area (SMA) and pre-motor cortex areas and the differences of language lateraliaztion among two word generation task To lateralization index survey in 1anguage area on right and left in brain get to activation area pixel in brain. Compared to visual and auditory instrument task in the language areas get to the lateralization index. Two language generation task high detection rates of Broca and Wernicke areas. The visual instruction no detected in the auditory area, and auditory instruction no detected in the visual area. There was statistics significant different of them among language generation task. 1'his indicated that language area obtained image of the brain functional MR imaging usefulness in the visual and auditory task instrument.

• Archives of Plastic Surgery
• /
• v.34 no.1
• /
• pp.93-98
• /
• 2007

Purpose: Many options are available for the incision and pocket selection in breast augmentation. Each method has its advantages and disadvantages. To leave an invisible operation scar and to achieve easier pocket dissection by the central location of the incision on the breast, we made a transareolar-perinipple incision. To overcome the disadvantages of the transareolar incision, originally advocated by Pitanguy in 1973, we modified the direction of incision line and dissection plane. Methods: To avoid the injury of 4th intercostal nerve responsible for nipple sensation, we made perinipple incision on the medial side of the nipple instead of trans-nipple incision and made the transareolar incision as 11-5 o'clock on the left side and 1-7 o'clock on the right side instead of 3-9 o'clock on both sides. To avoid the possible infection and breast feeding problem caused by the injury to the lactiferous duct, and the possible implant hernia caused by the incisions lying on a same plane of pocket dissection, we made a subcutaneous dissection just above the breast tissue medially down to the bottom of breast tissue and made a subglandular or subfascial pocket, which may avoid the injury of lactiferous duct and create different planes for skin incision and pocket dissection. Other advantages of the transareolar-perinipple incision include easier pocket dissection, less chance of hematoma, and as a result less postoperative pain because of the central location of the approach which allow finger dissection and meticulous bleeding control with direct vision, without any specialized instrument such as an endoscope or long mammary dissectors. As for pocket selection, we made dual pockets. We prefer subglandular or subfascial pocket. Also, we made a subpectoral pocket in the upper 1/4 of the pocket to add more volume on the upper part of the augmented breast, which can make aesthetically more desirable breasts in thin Asian women with small breasts. Possible disadvantages of our method are subclinical infection and scar widening, which could be overcome by meticulous operation techniques, antibiotic therapy, and intradermal tattooing. Results: From September, 2003 to August, 2005, 12 patients underwent breast augmentation using round smooth surface saline implants by our method. During the mean follow-up period of 13 months, there were no complications such as infection, hematoma, capsular contracture, and sensory change of nipple, and results were satisfactory. Conclusion: We suggest breast augmentation via transareolar-perinipple incision and dual pockets(subpectoral-subglandular or subfascial) as a valuable method in thin oriental women with small breasts.

• Archives of Plastic Surgery
• /
• v.34 no.2
• /
• pp.191-196
• /
• 2007

Purpose: Gluteal perforator is easily identified in the gluteal region and gluteal perforator flap is a very versatile flap in sacral sore reconstruction. We obtained satisfying results using the gluteal perforator flap, so we report this clinical experiences with a review of the literature. Methods: Between November of 2003 and April 2006, the authors used 16 gluteal perforator flaps in 16 consecutive patients for coverage of sacral pressure sores. The mean age of the patients was 47.4 years (range, 14 to 78 years), and there were 9 male and 7 female patients. All flaps in the series were supplied by musculocutaneous arteries and its venae comitantes penetrating the gluteus maximus muscle and reaching the intrafascial and suprafascial planes, and the overlying skin forming a rich vascular plexus arising from gluteal muscles. Patients were followed up for a mean period of 11.5 months. Results: All flaps survived except one that had undergone total necrosis by patient's negligence. Wound dehiscence was observed in three patients and treated by secondary closure. There was no recurrence during the follow-up period. Conclusion: Gluteal perforator flaps allow safe and reliable options for coverage of sacral pressure sores with minimal donor site morbidity, and do not sacrifice the gluteus maximus muscle and rarely lead to post-operative complications. Freedom in flap design and easy-to perform make gluteal perforator flap an excellent choice for selected patients.

• Journal of the Korean Geotechnical Society
• /
• v.33 no.11
• /
• pp.59-72
• /
• 2017

In this study, the calculation method of the active earth pressure acting on the imaginary vertical plane at the end of the heel of the wall is proposed. For cantilever retaining wall, a change of shear zone behind the wall affects the earth pressure in the vertical plane at the end of heel of the wall depending on wall friction and angle of ground slope. It is very complicated to calculate the earth pressure by a limit equilibrium method (LEM) which considers angles of failure planes varying according to the heel length of the wall. So, the limit analysis method (LAM) is used for calculation of earth pressure in this study. Using the LAM, the earth pressures considering the actual slope angles of failure plane are calculated accurately, and then horizontal and vertical earth pressures are obtained from them respectively. This study results show that by decreasing the relative length of the heel, the slope angle of inward failure plane becomes larger than theoretical slope angle but the slope angle of outward failure plane does not change. And also the friction angle on the vertical plane at the end of the heel of the wall is between the ground slope angle and the wall friction angle, thereafter the active earth pressure decreases. Finally, the Coulomb earth pressure can be easily calculated from the relationship between friction angle (the ratio of vertical earth pressure to horizontal earth pressure) and relative length of the heel (the ratio of heel length to wall height).

• Bulletin of the Korean Chemical Society
• /
• v.22 no.1
• /
• pp.30-36
• /
• 2001

The crystal structures of fully dehydrated $Pd^{2+}$ - and $TI^{+}$ -exchanged zeolite X, $Pd_{18}TI_{56}Si_{100}Al_{92}O_{384}(Pd_{18}TI_{50-}X$, a = $24.935(4)\AA$ and $Pd_{21}TI_{50}Si_{100}Al_{92}O_{384}(Pd_{21}TI_{50-}X$ a = $24.914(4)\AA)$, have been determined by single-crystal X-ray diffraction methods in the cubic space group Fd3 at $21(1)^{\circ}C.$ The crystals were prepared using an exchange solution that had a $Pd(NH_3)_4Cl_2\;:TINO_3$ mole ratio of 50 : 1 and 200 : 1, respectively, with a total concentration of 0.05M for 4 days. After dehydration at $360^{\circ}C$ and 2 ${\times}$$10^{-6}$ Torr in flowing oxygen for 2 days, the crystals were evacuated at $21(1)^{\circ}C$ for 2 hours. They were refined to the final error indices $R_1$ = 0.045 and $R_2$ = 0.038 with 344 reflections for $Pd_{18}Tl_{56-}X$, and $R_1$ = 0.043 and $R_2$ = 0.045 with 280 reflections for $Pd_{21}Tl_{50-}X$; I > $3\sigma(I).$ In the structure of dehydrated $Pd_{18}Tl_{56-}X$, eighteen $Pd^{2+}$ ions and fourteen $TI^{+}$ ions are located at site I'. About twenty-seven $TI^{+}$ ions occupy site II recessed $1.74\AA$ into a supercage from the plane of three oxygens. The remaining fifteen $TI^{+}$ ions are distributed over two non-equivalent III' sites, with occupancies of 11 and 4, respectively. In the structure of $Pd_{21}Tl_{50-}X$, twenty $Pd^{2+}$ and ten $TI^{+}$ ions occupy site I', and one $Pd^{2+}$ ion is at site I. About twenty-three $TI^{+}$ ions occupy site II, and the remaining seventeen $TI^{+}$ ions are distributed over two different III' sites. $Pd^{2+}$ ions show a limit of exchange (ca. 39% and 46%), though their concentration of exchange was much higher than that of $TI^{+}$ ions. $Pd^{2+}$ ions tend to occupy site I', where they fit the double six-ring plane as nearly ideal trigonal planar. $TI^{+}$ ions fill the remaining I' sites, then occupy site II and two different III' sites. The two crystal structures show that approximately two and one-half I' sites per sodalite cage may be occupied by $Pd^{2+}$ ions. The remaining I' sites are occupied by $TI^{+}$ ions with Tl-O bond distance that is shorter than the sum of their ionic radii. The electrostatic repulsion between two large $TI^{+}$ ions and between $TI^{+}$ and $Pd^{2+}$ ions in the same $\beta-cage$ pushes each other to the charged six-ring planes. It causes the Tl-O bond to have some covalent character. However, $TI^{+}$ ions at site II form ionic bonds with three oxygens because the super-cage has the available space to obtain the reliable ionic bonds.

• Bulletin of the Korean Chemical Society
• /
• v.21 no.10
• /
• pp.1041-1043
• /
• 2000

We present the effects of temperature (between 10 K and 298 K) and of hole concentration on the frequency and intensity of characteristic phonons in polycrystalline $La_2CuO_4-related$ compounds using FT-IR spectros-copy. The influences of the concentration of carrier doped on the phonon modes are prominent in the IR spectra of $La_2CuO_4-related$ compounds. For $La_2-xSrxCuO_4({\chi}=$ 0.00, 0.03, 0.07, 0.10, and 0.15) and electrochemically (or chemically) oxidized $La_2CuO_4$, the intensities of the transverse oxygen mode around 680cm $-^1$ which cor-responds mainly to Cu-O(1) stretching vibration in the basal plane of CuO6 octahedron, are decreased and dis-appeared depending on the Sr-substitution rate and the amount of excess oxygen, while the longitudinal oxygen mode around 510 cm $-^1$ corresponding to the Cu-O(2) stretching in the basal plane of CuO6 octahedron are near-ly invariable. In particular, after two cycles of cooling-heating between 10 K and 298 K for these sample, the phonons around 680 cm $-^1$ are blue shif 13-15 cm $-^1$, while the phonons around 510 cm $-^1$ are nearly constant. The introduction of the charge carrier by doping would give rise to the small contraction of CuO6 oc-tahedron as Cu $^3+$ requires a smaller site than Cu $^2+$, which results in the shortening of the Cu-O(1) bond length and Cu-O(2) bond length with the increased La-O(2) bond length. These results in the frequency shift of the characteristic phonons. The IR spectra of $La_2Li0.5Cu0.5O_4$ which exhibits an insulator behavior despite the $Cu^3+$ of nearly 100%, corroborate our IR interpretations. The mode around 710 cm $-^1$ corresponding to Cu-O(1) stretching vibration is still strongly remained even at low temperature (10 K). Thus, we conclude that the con-duction electrons formed within $CuO_2$ planes of $La_2CuO_4-related$ superconductors screen more effectively the transverse oxygen breathing mode around 680 $cm-^1$ depending on the concentration of the doped charge carrier in $La_2CuO_4-related$ compounds, which might use as a superconductivity probe.