• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.36D no.7
• /
• pp.42-49
• /
• 1999

In this paper, we proposed a simple measurement method to find the behaviors of the fiber-to-waveguide coupler. The polished fiber blocks and planar waveguides on silicon dioxide were fabricated independently and then optically coupled by physical pressure. Several kinds of polymer with different refractive indices were used for waveguide films. The proposed method makes it possible to measure the center wavelength, bandwidth, extinction ratio, and polarization dependence of the coupler during fabrication procedure. The wavelength sensitivity increased with refractive index of polymer. The symmetric planar waveguide structure and isotropic property of guiding materials reduced polarization dependent property. Insertion loss of the coupler was less than 0.5dB. It is expected that our measurement method is useful for developing various optical devices using evanescent coupling between polished fiber and planar waveguide such as optical modulators and filters etc.

• Korean Journal of Optics and Photonics
• /
• v.15 no.6
• /
• pp.490-494
• /
• 2004

Bragg gratings were fabricated in Ge-doped silica planar lightwave circuits (PLC) for different writing conditions to study the growth characteristics. The refractive index modulation of the gratings grew in the PLC with total fluence F according to the power law $\Delta$n=A $F^{B}$. The characteristics of the PLC gratings formed for external cavity lasers match closely to those predicted by the power law. The oscillation spectra of the FP-LD with a Bragg grating grown in the PLC waveguide were also presented.d.

• Journal of the Korean Society of Safety
• /
• v.29 no.4
• /
• pp.34-41
• /
• 2014

The goal of this study is to investigate some crack behaviors which affect the crack propagation angle at the planar solid oxide fuel cell with cracks under the fabricating and operating temperature and analyze the stresses by 3 steps processing on the solid oxide fuel cell. Currently, there are lots of researches of the performance improvement for fuel cells, and also for the more powerful efficiency. However, the planar solid oxide fuel cell has demerits which the electrode materials have much brittle properties and the thermal condition during the operating process. It brings some problems which have lower reliability owing to the deformation and cracks from the thermal expansion differences between the electrolyte, cathode and anode electrodes. Especially the crack in the corner of the electrodes gives rise to the fracture and deterioration of the fuel cells. Thus it is important to evaluate the behavior of the cracks in the solid oxide fuel cell for the performance and safety operation. From the results, we showed the stress distributions from the cathode to the anode and the effects of the edge crack in the electrolyte and the slant crack in the anode. Futhermore the crack propagation angle was expected according to the crack length and slant angle and the variation of the stress intensity factors for the each fracture mode was shown.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.5 no.3
• /
• pp.101-109
• /
• 2012

Because the installation problem of parabola antenna that is tilted to 45 degree when this antenna is installed at the area of middle latitude, the study on planar antenna in place of parabola antenna is made rapid progess. Especially, The development of the planar antenna for VSAT is needed depending on the increased Ka-band satellite communications. In this paper, in order to meet with these performances, an array antenna consisting of the vertical polarized waveguide longitudinal slots based on the leaky-wave mode of traveling wave antenna is proposed. Especially, for the lower sidelobe level, the design method of the radiation power distribution control using the different slot widths is proposed. An array antenna consisting of 32 leakywave waveguide antennas is showing 35.16 dBi of gain, 2.5 degree of beamwidth at azimuth, below than -30 dB of sidelobe level, 45.8 degree of beam tilt angle in center frequency 30.2 GHz.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.12
• /
• pp.1337-1342
• /
• 2012

In this paper, we propose a novel reconfigurable antenna that can change the electrical shape of the matching network using RF switches of PIN diodes. The designed antenna operates at two different modes that are Mode 1 (HSDPA band, 2.1~2.2 GHz) and Mode 2(WiBro WiFi band, 2.3~2.5 GHz). The antenna is built on both sides of a polyarcylate substrate. The measured reflection coefficient shows a matching bandwidth of 547 MHz($S_{11}$ <-3 dB, 2.035~2.582 GHz) for Mode 1 and 600 MHz($S_{11}$ <-3 dB, 2.2~2.8 GHz) for Mode 2, and it shows average vertical gains of -4.4 dBi and -4.5 dBi in x-y plane, respectively.

• Journal of Ocean Engineering and Technology
• /
• v.23 no.2
• /
• pp.1-7
• /
• 2009

This paper presents a sliding mode controller based on Ackermann's formula and applies it to stabilizing a two-wheeled mobile inverted pendulum in equilibrium. The mobile inverted pendulum is a system with an inverted pendulum on a mobile cart. The dynamic modeling of the mobile inverted pendulum was established under the assumptions of a cart with no slip and a pendulum with only planar motion. The proposed sliding mode controller was based upon a class of nonlinear systems whose nonlinear part of the modeling can be linearly parameterized. The sliding surface was obtained in an explicit form using Ackermann's formula, and then a control law was designed from reachability conditions and made the sliding surface attractive to the equilibrium state of the mobile inverted pendulum. The proposed controller was implemented in a Microchip PIC16F877 micro-controller. The developed overall control system is described. The simulation and experimental results are presented to show the effectiveness of the modeling and controller.

• Journal of Sensor Science and Technology
• /
• v.15 no.4
• /
• pp.231-236
• /
• 2006

Single-mode planar waveguide type UV sensor was fabricated using SU-8 and photochromic dye. Polymer waveguide was fabricated $10{\mu}m$ width and $2{\mu}m$ thickness for single-mode operation. The UV sensor had an absorbance with $0.0396{\sim}0.114$ absorbance/mW respectively when the 5 mm sensing area was irradiated with UV for 3 sec. And sensor had a linear properties by sensing area variation. Proposed single-mode sensor had more excellent properties of UV sensitivity than other UV sensors.

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.2 s.95
• /
• pp.225-233
• /
• 1999

This paper describes a versatile finite element technique which has been used to investigate of wide range of structural defects of practical importance. The procedure automatically remeshes the three-dimensional finite element model during the stages of crack growth. Problems analyzed to date include the surface cracks in leak-before-break situations, the development of quarter-elliptical corner defects, planar semi-elliptical surface defects and the fatigue growth of defects.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.35D no.7
• /
• pp.25-31
• /
• 1998

Modal transmission-line is utilized to analyze the power coupling of optical directional coupler composed by two parallel guiding slabs. By defining a coupling efficiency .eta. amenable to rigorous supermodes and boundary conditions of modal functions, we evaluate the power transfer for TE mode of gainy coupler. The results reveal that optimized power exchange occurs at a novel wavelength .lambda.$_{op}$ , which is generally different from minimum gap .lambda.$_{min}$ between rigorous modes and phase-matching condition .lambda.$_{ph}$ .

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1997.04a
• /
• pp.493-499
• /
• 1997

In this study, the changes in transmitting and receiving characteristics, especially resonance frequencies, of the underwater acoustic planar array transducer by the transformers used in the analog weighting circuit are investigated. Electrical equivalent circuit analysis shows that an ideal transformer does not change the resonance frequency of the transmitting mode, but the resonance frequency which gives the maximum receiving sensitivity can be designed by adjusting the magnitude of reactance of transformer.