• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.10a
• /
• pp.1051-1054
• /
• 2005

On this study, we optimized minimizing the characteristic function for mixed result of the structural contact analysis and the buckling analysis according to the pin jig initial model's level change using mixed the table of orthogonal away and ANOM, Pin jig's weight is reduced up to 20 percent considering constraint conditions. Also we optimized reducing 20 percent weight of pin jig model using topology optimization.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.9 no.3
• /
• pp.259-267
• /
• 1997

Average heat transfer coefficients and friction coefficients have been measured from staggered short pin-fin arrays to investigate the effect of fin shapes. Flow entering into the test section is a fully developed duct flow and the Reynolds number ranges from 5,000 to 25,000 based on fin diameter and average approaching velocity. The fin has three different shapes; uniform-diameter circular fin, two stepped-diameter circular fins. Average heat transfer rates change slightly with the fin shapes. However, friction loss(pressure loss) for the stepped-diameter fins is significantly less than that for the uniform-diameter fin. This results indicate that the stepped-diameter fin arrays in duct flow enhance heat transfer rates largely based on unit pumping power.

• Proceedings of the KIEE Conference
• /
• 1996.07c
• /
• pp.1950-1953
• /
• 1996

A $1\;{\times}\;4$ micro mirror array is designed and fabricated. In contrast to other micro mirrors which utilize torsional flexure hinges or cantilevers for restoring torque and supporting purpose, we have placed a substrate hinge structure under each mirror. Each micro mirror consists of address electrode, substrate hinge consisting of pin and staple, supporter post, and mirror plate. Electrical connection between mirror plate and ground electrode is established by substrate hinge. Mirror undergoes a rotational motion due to electrostatic force when voltage difference is applied between address electrode and mirror plate. Micro mirrors with two different types of staple shape and two different pin sizes are designed and fabricated. Each mirror is designed to have ${\pm}\;10^{\circ}$ of deflection angle and have $100\;{\times}\;110\;{\mu}m^2$ of size.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.05a
• /
• pp.164-169
• /
• 2005

Microphone array techniques are being used widely in wind tunnel measurements for identification of the distributed aerodynamic noise sources on the model being tested. Depending on the frequencies and sound levels, conventional beamforming algorithm has limitation in separating two adjacent sources. Several modifications to the classical beamforming have been developed to enhance way resolution and reduce sidelobe levels. In this Paper the robust adaptive beamforming and the CLEAN algorithm are used to compare to the result of conventional beamforming method. It is found that the CLEAN algorithm is capable of pin-pointing locations of multiple sources nearby, while these sources are unidentifiable with robust adaptive or conventional beamforming techniques.

• Tribology and Lubricants
• /
• v.24 no.6
• /
• pp.368-373
• /
• 2008

This paper will investigate the friction characteristics of a 100m Hexagonal Array, Micro-scale Dimple Pattern, on bearing steel. These characteristics are researched by utilizing a pin-on-disk wear test machine, under various test conditions. The reduction of friction is a necessary requirement for the improved efficiency of this machine. As the speed increases, there is a decrease in the effect of the dimple of friction characteristic, with substantially little change to density. Conversely, as the load increases, the dimple pattern grows larger, resulting in a difference in the texture of these two components. At a dimple density of 10% the friction characteristic is easily demonstrated, with a consistent change in both speed and load.

• ETRI Journal
• /
• v.41 no.6
• /
• pp.715-730
• /
• 2019

We propose a switched beam-forming antenna that satisfies not only ultra-wideband characteristics but also beam-forming in the WLAN frequency band using an ultra-wideband antenna and passive parasitic elements applying a broadband optimal reactance load algorithm. We design a power and phase estimation function and an error correction function by re-analyzing and normalizing all the components of the parasitic array using control system engineering. The proposed antenna is compared with an antenna with a pin diode and reactance load value, respectively. The pin diode is located between the passive parasitic elements and ground plane. An antenna beam can be formed in eight directions according to the pin diode ON (reflector)/OFF (director) state. The antenna with a reactance load value achieves a better VSWR and gain than the antenna with a pin diode. We confirm that a beam is formed in eight directions owing to the RF switch operation, and the measured peak gain is 7 dBi at 2.45 GHz and 10 dBi at 5.8 GHz.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.39 no.5
• /
• pp.34-42
• /
• 2002

In this paper, we designed the VLSI array architecture for the high speed processing of the motion estimation used by block matching algorithm. We derived the one dimensional systolic array from the full search block matching algorithm. The data and control signals of the proposed systolic array are passed through adjacent processing element. So proposed architecture has temporal and spatial locality. The I/O ports exists only in the first and last processing elements of the array. This architecture has low pin counts and modular expandability. So the proposed array architecture can be cascaded for different block size and search range.

• Journal of the Korean Society for Precision Engineering
• /
• v.24 no.5
• /
• pp.82-88
• /
• 2007

This work is to fabricate a precise optical fiber array using polymer composite for optical interconnection. Optical fiber array has to satisfy low optical loss requirement less than 0.4 dB according to temperature change. For this purpose, design criteria for an optical fiber array was derived. The coefficient of thermal expansion of silica particulate epoxy composites was affected by volume fraction of silica particles. And also, elastic modulus of silica particulate epoxy composites was affected by volume fraction of silica particles. To obtain the coefficients of thermal expansion below $10{\times}10E-6/^{\circ}C$ and elastic modulus more than 20 GPa , we chose the volume fraction more than 76%. Using silica particulate epoxy composites with the volume fraction 76%, 8-channel optical fiber array with dimensional tolerances below $1\;{\mu}m$ was manufactured by transfer molding technique using dies with the uniquely-designed core pin and precisely-machined zirconia ceramic V block. These optical fiber arrays showed optical loss variations within 0.4 dB under thermal cycling test and high temperature test.

• Journal of Radiation Protection and Research
• /
• v.29 no.4
• /
• pp.257-261
• /
• 2004

A coded-aperture gamma camera was developed to increase the sensitivity of a pin hole camera made with a pixellated CsI(Tl) scintillator and a position-sensitive photomultiplier tube. The modified round-hole uniformly redundant array of pixel size $13{\times}11$ was chosen as a coded mask considering the detector spatial resolution. The performance of the coded-aperture camera was compared with the pin hole camera using various forms of Tc-99m source to see the improvement of signal-to-noise ratio or the improvement of the sensitivity. The image quality is much improved despite of a slight degradation of the spatial resolution. Though the camera and the test were made for low energy case, but the concept of the coded-aperture gamma camera could be effectively used for the radioactive environmental monitoring and other applications.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.21 no.3
• /
• pp.763-770
• /
• 1996

In this paper, the Single-stage Transmission type Injectiong-Locked Oscillator(STILO) was designed and fabicated for the Active Integrated Phased Array Antenna(AIPAA) system. The STILO, which was designed and fabricated by injection-locked technique and hair-pin resonator, has the same 210MHz frequency tuning range of the Voltage Controlled Oscillator(VCO) used by varactor. The locking bandwidth of STILO with 11.5MHz bandwidth, is much better than that of the Injection-Locked Dielectric Resonator Oscillator(ILDRO), And the STILO has the improved noise characteristics in AM, FM, and PM. This STILO is useful for the AIPAA, the coupled VCO array, an the MMIC structure.