• Earthquakes and Structures
• /
• v.19 no.4
• /
• pp.273-286
• /
• 2020

The pile group foundation is widely used for gravity pier of high-speed railway bridges in China. If a moderate or strong earthquake occurs, the pile-surrounding soil will exhibit obvious nonlinearity and significant pile group effect. In this study, an improved pushover analysis model for the pile group foundation with consideration of pile group effect is presented and validated by the quasi-static test. The improved model uses simplified springs to simulate the soil lateral resistance, side friction and tip resistance. PM (axial load-bending moment) plastic hinge model is introduced to simulate the impact of the axial force changing of pile group on their elastic-plastic characteristics. The pile group effect is considered in stress-stain relations of the lateral soil resistance with a reduction factor. The influence factors on nonlinear characteristics and plastic hinge distribution of the pile group foundation are discussed, including the pier height, longitudinal reinforcement ratio and stirrup ratio of the pile, and soil mechanical parameters. Furthermore, the displacement ductility factor, resistance increase factor and yielding stiffness ratio are provided to evaluate the seismic performance of soil-pile system. A case study for the pile group foundation of a railway simply supported beam bridge with a 32 m-span is conducted by numerical analysis. It is shown that the ultimate lateral force of pile group is not determined by the yielding force of the single one in these piles. Therefore, the pile group effect is essential for the seismic performance evaluation of the railway bridge with pile group foundation.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2009.09a
• /
• pp.877-883
• /
• 2009

Shaking table tests are performed to evaluate the dynamic group pile effect in fine sand. Single pile tests and $2{\times}4$ group pile tests are performed on 3D pile spacing. Dynamic p-y backbone curves are obtained to evaluate dynamic group pile effect by using dynamic p-y curve of single pile. And dynamic group pile p-multiplier is estimated by dynamic p-y backbone curve. Dynamic p-multiplier can be calculated by using subground reaction ratio of dynamic p-y backbone curve which is the same displacement of p-y curve peak point As the result, dynamic group pile effects are evaluated in terms of a shaking frequency, a shaking acceleration, and a relative density. Dynamic group pile p-multiplier is the largest at lead pile, and the value decrease at middle pile and trail pile. p multiplier increases as increasing input acceleration and decreasing relative density. This results coincide with NCHRP's research which suggest p multiplier increases as increasing pile cap displacement.

• Journal of the Korean GEO-environmental Society
• /
• v.20 no.8
• /
• pp.5-12
• /
• 2019

A pile group, that consists of several piles connected by a pile cap, is used as the superstructure. The pile supports vertical and horizontal load to design the pile group, but the effect of bearing capacity of the pile cap has not considered. Various researches have been conducted to reflect the effect of bearing capacity of the pile cap in order to reduce the amount of piles in the range of the stability under the vertical load of the superstructure. However, the effect of bearing capacity under the horizontal seismic load has not been studied adequately. Therefore, a shaking table test was carried out with different-sized pile caps that support the superstructure in this study. This test was to verify the influence of the size of the pile cap in the group pile under the horizontal load. The result shows that the size of the pile cap affects to the dynamic behavior of the superstructure and the pile group. Also, the bigger size of the pile group makes the larger constraint effect of ground, and it results that both the ground and the pile moves as a whole.

• Journal of the Korean GEO-environmental Society
• /
• v.20 no.10
• /
• pp.39-46
• /
• 2019

The interaction between the ground and structures should be considered for seismic design of group piles supporting the superstructure. The p-y curve has been used widely for the analysis of nonlinear relationship between the ground and structures, and various researches have conducted to apply the dynamic p-y curve for seismic design of group piles. This curve considers the interaction between the ground and structures under the dynamic load such as an earthquake. However the supported effect by the pile cap and the interaction by inertia behavior of superstructures. Therefore, the shaking table test was conducted to verify the effect of the change of the pile cap in group piles supporting superstructures embedded in sandy soil. The test condition is that the arrangement and distance between centers of piles are fixed and the length of the pile cap is changed for various distances between the pile cap side and the pile center. The result shows that the distance between the pile cap side and the pile center have an effect on the dynamic p-y curve and the effect of group piles.

• Proceedings of the Korean Geotechical Society Conference
• /
• 1999.03a
• /
• pp.259-266
• /
• 1999

In case that pile cap is in direct contact with underlying soil, the bearing mechanism for pile groups, including direct bearing effect of cap and its induced influence on pile-soil-cap interaction, should be properly considered. In this paper, the effects of pile caps on behaviors of pile groups in sandy soils were investigated by model tests, which consist of tests on 3 by 3 pile groups with/without contact on subsoil, single pile with/without contact and cap as a shallow foundation. Also, the influences of pile spacing in group piles on contact effects were investigated. The test results showed that the load carrying capacity of pile cap was large enough not to be ignored. However, the interaction effects due to contact between cap and subsoils were not revealed obviously in working load range. And in the design of pile groups, the bearing effect of pile cap when contacted with subsoils, can be reflected by simply summing up load settlement behaviors of each cap and group piles without contact.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2001.03a
• /
• pp.363-370
• /
• 2001

A computationally efficient algorithm to analyze a group pile behavior is proposed by consideration of both soil-pile and pile-cap interactions. Using toad transfer method the nonlinear characteristics of the soil-pile interaction for a single pile is modeled by piecewise linear soil springs (p-y, t-z, and q-z curves). Beam-column method, one of the most practical approaches, is used for numerical modeling of the soil-pile system. In addition to the group effect resulting from the soil-pile-soil interaction, for a more realistic analysis it is essential to consider the effect of pile-cap interaction including geometric configuration of the piles in a group and conectivity conditions between piles and the cap. This paper mainly focuses on the pile-cap interaction and the development of a rational numerical procedure of its incorporation with the beam-column method.

• Journal of the Korean Geotechnical Society
• /
• v.16 no.1
• /
• pp.117-129
• /
• 2000

This paper discusses the lateral behavior of group pile in homogeneous and non- homogeneous (two layered) soil. In the group pile, the model tests were to investigate the effects on spacing-to-diameter ratio of pile, pile array, ratio of pile spacing, constraint condition of pile tip, eccentric load and ground condition. The group efficiency and lateral deflection induced in active piles were found to be highly dependent on the spacing-to-diameter ratio of pile, number of pile. Lateral bearing capacities in the group piles of fixed tip, in the case of 6D spacing and $3\times3$ array, were 40-100% higher than those in the group pile of free tip. Based on the results obtained, a spacing-to-diameter of 6.0 seems to be large enough to eliminate the group effect for the case of relative density of 61.8% and 32.8%, and then each pile in such a case behaves essentially the same as a single pile. However, in the case of dense sand, it can be estimated that a spacing-to-diameter of 8.0 seems to be large enough to eliminate the group effect. In this study the group efficiency is illustrated in experimental function with spacing-to-diameter, S/D, relative density and number of pile. The distribution of shear force in lead row piles, in the case of 3$\times$3 array group pile, was 41.6-52.4% for 3D spacing and 34-40% for 6D spacing, respectively. The shadowing effect for the parallel direction of lateral loading appears to be more significant than the one for the perpendicular direction of lateral loading.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2010.09b
• /
• pp.96-103
• /
• 2010

This paper presents of effect of tunneling on pile group of being operated bridge using Three-dimensional numerical modeling to study the effect of coordination of tunneling location under discontinuous group pile. In order to find idealistic tunneling location that causes settlement, change of stress on the piles and movement of soil at a minimum, a fully coupled 3D finite element model is adopted. The study contains pile settlement, axial force on each piles in the group, axial displacement of piles and soil behaviour caused by tunneling. Based on the result some insights into the pile behavior due to tunneling obtained from numerical analysis were mentioned and discussed.

• Journal of the Korean Geotechnical Society
• /
• v.18 no.1
• /
• pp.127-132
• /
• 2002

Shaking table tests are performed on model group piles to investigate the mechanics of dynamic pile-soil interaction, and to evaluate the dynamic group pile effect. Tests are executed on a single pile as well as group piles($3\times3$) by varying a pile spacing from 3D to 8D. A lumped mass is located on top of piles to simulate a superstructure. Dynamic p-y curves of the single pile and the group piles are obtained from the tests and compared with the backbone slopes of API cyclic p-y curves. From the comparisons, dynamic pile group effects are evaluated in terms of a pile spacing, a shaking frequency, and a shaking intensity.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.38 no.4
• /
• pp.567-578
• /
• 2018

In this study, to investigate the effect of the stress reduction of group piles by dynamic loading, a dynamic p-y curve was established and the dynamic p-multiplier was calculated. Dynamic numerical analysis was performed by input sinusoidal waves to the bottom of the pile - ground system for $2{\times}2$ group pile, single pile and $5{\times}5$ group pile, single pile in dry sandy soil, and the pile spacing was changed to 2.5 and 5.0 times of the pile diameter. By establishing and comparing the dynamic p-y curves of the single pile and group piles, the dynamic group pile effect of the piles according to the pile center spacing and row position of the group pile piles is analyzed. $5{\times}5$ showed symmetry of the dynamic P-multiplier value around the pile origin coordinate. The dynamic p-multiplier value at the single pile, $5{\times}5$ pile (pile spacing: 2.5D) is 0.26 ~ 0.30 at the pile number 3, pile number 23, 0.14 pile number 13, and 0.14 ~ 0.38 at the pile number 5, pile number 18. These values differed from the static p-multiplier, especially due to the different loading conditions. The dynamic p-multiplier ($P_{dm}$) estimation through various types of input dynamic loads is expected to be used for dynamic design and analysis of group pile-ground systems of civil foundation structures.