• Proceedings of the Materials Research Society of Korea Conference
• /
• 2009.05a
• /
• pp.31.1-31.1
• /
• 2009

Carbon nanotubes (CNTs) are attractive material because of their superior electrical, mechanical, and chemical properties. Furthermore, their geometric features such as a large aspect ratio and a small radius of curvature at tip make them ideal for low-voltage field emission devices including backlight units of liquid crystal display, lighting lamps, X-ray source, microwave amplifiers, electron microscopes, etc. In field emission devices for display applications, the phosphor anode is positioned against the CNT emitters. In most case, light generated from the phosphor by electron bombardment passes through the anode front plate to reach observers. However, light is produced in a narrow depth of the surface of the phosphor layer because phosphor particles are big as much as several micrometers, which means that it is necessary to transmit through the phosphor layer. Hence, a drop of light intensity is unavoidable during this process. In this study, we fabricated a transparent cathode back plate by depositing an ultra-thin film of single walled CNTs (SWCNTs) on an indium tin oxide (ITO)-coated glass substrate. Two types of phosphor anode plates were employed to our transparent cathode back plate: One is an ITO glass substrate with a phosphor layer and the other is a Cr-coated glass substrate with phosphor layer. For the former case, light was radiated from both the front and the back sides, where luminance on the back was ~30% higher than that on the front in our experiments. For the other case, however, light was emitted only from the cathode back side as the Cr layer on the anode glass rolled as a reflecting mirror, improving the light luminance as much as ~60% compared with that on the front of one. This study seems to be discussed about the morphologies and field emission characteristics of CNT emitters according to the experimental parameters in fabricating the lamps emitting light on the both sides or only on the cathode back side. The experimental procedures are as follows. First, a CNT aqueous solution was prepared by ultrasonically dispersing purified SWCNTs in deionized water with sodium dodecyl sulfate (SDS). A milliliter or even several tens of micro-liters of CNT solution was deposited onto a porous alumina membrane through vacuum filtration. Thereafter, the alumina membrane was solvated with the 3 M NaOH solution and the floating CNT film was easily transferred to an ITO glass substrate. It is required for CNT film to make standing CNTs up to serve as electron emitter through an adhesive roller activation.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.339-341
• /
• 2009

A transparent plasma display was developed using transparent glass barrier ribs. Glass barrier ribs were fabricated via a wet etching process. Glass barrier ribs created using a top and bottom etching process showed better transparency compared to those created through only a top etching process. A see-through phosphor layer was obtained by coating the sidewall of the barrier ribs with a conventional opaque phosphor. A fabricated prototype of a transparent plasma display was clear enough to see the background beyond the panel and was well operated by a conventional driving scheme. The maximum luminance was 1150 cd/$m^2$ and the maximum luminous efficacy was 1.35 lm/W in a Ne+13.5%Xe gas-mixture and green cells.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.4
• /
• pp.330-334
• /
• 2013

We developed a package of remote phosphor structure having blue LED chips and phosphors physically separated, and the characteristics were evaluated according to different classifications of phosphor coatings. Remote phosphor was produced by screen printing coating on glass substrate with phosphor content rated paste and heat treatment. After mounting Remote phosphor, which has been classified according to number of coatings, on top of blue LED chips, luminous flux, luminous efficacy, CCT and CRI were measured. The measurement results showed the most suitable characteristics of white LED package as a general light source when the content rate of phosphor in Remote phosphor was 80 wt.% with 3 layers of coatings and thickness over $12{\mu}m$.

• Journal of the Korean Ceramic Society
• /
• v.53 no.2
• /
• pp.258-262
• /
• 2016

The effect of zirconium dioxide ($ZrO_2$) on the properties of color conversion glasses was examined in the $BaO-ZnO-B_2O_3-SiO_2$ system. The difference in refractive index between glass and phosphor affect the optical properties of the color conversion glass because of light scattering. Reducing the difference in refractive index is a method to improve the luminous efficacy of color conversion glasses. As a reference, a type of glass that contains 25 mol% of each component was used. To increase the refractive index of the glass samples, the BaO content was increased from 25 to 40 mol%, and $ZrO_2$ was added at levels of 1, 3, and 5 mol%. Color conversion glasses were prepared by sintering a mixture of glass and 5 wt% $YAG:Ce^{3+}$ phosphor. As a result, the refractive index of the glass was found to be dependent on the BaO and $ZrO_2$ contents in the BaO-ZnO-$B_2O_3-SiO_2$ system. As the BaO and $ZrO_2$ contents were increased, the luminous efficacy of the color conversion glass was improved because the refractive index difference between the glass and the $YAG:Ce^{3+}$ phosphor decreased.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.51 no.1
• /
• pp.31-38
• /
• 2002

We measured a 3-dimensional images of the light emitted from plasma display panel(PDP) by using newly proposed scanned point detecting system. In the panel without phosphor, as we scan from the rear glass to the front glass, the detected light intensity increases and the light intensity detected in the inside edge of the ITO electrodes shows the stronger intensity than others. The light intensity detected between the barrier ribs shows the largest value of brightness. Also, as the sustain voltage increases, the detected light intensity increases. In the panel with phosphor, the intensity of light detected at barrier rib shows the stronger light intensity than rear plate. Therefore, the phosphor of barrier rib is very important. From these results the 3-dimensional measurement is necessary to understand exactly the discharge phenomenon in the PDP cell.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07b
• /
• pp.1060-1062
• /
• 2002

Spherical and dense BAM phosphor particles were prepared by spray pyrolysis. The key idea of dense BAM particles is to lead gelation in droplets, which was successfully achieved by using the aluminum polycation as the precursor solution for the spray pyrolysis. The BAM phosphor particles prepared by spraying the aluminum polycation solution have completely spherical shape and dense structure. When directly applied to make phosphor film on the glass by the screen-printing method, the prepared spherical BAM phosphor particles showed better packing density and surface morphology than that of commercial one, which has irregular shape and large particle size. It was also found that the thermal degradation in the photoluminescence intensity for dense and spherical BAM particles was less than that of commercial one.

• Ceramist
• /
• v.21 no.1
• /
• pp.80-97
• /
• 2018

To realize a high luminous efficacy and a high emission color purity for the white-LEDs, the understanding for luminescence properties of the phosphors is significantly important because the performance of white-LEDs is directly affected by the luminescence properties of the phosphors. In this paper, therefore, we reviewed some commercially available $Eu^{2+}$- and $Ce^{3+}$- activated phosphors and discussed for the luminescence properties of these phosphors.

• Korean Journal of Materials Research
• /
• v.26 no.1
• /
• pp.22-28
• /
• 2016

In this study, we fabricated high quality color conversion component with green/red phosphor and low melting glass frit. The color conversion component was prepared by placing the green and red phosphor layer on slide glass via screen printing process. The properties of color conversion component could be controlled by changing coating sequence, layer thickness and heat treatment temperature. We discovered that optical properties of color conversion component were generally determined by the lowest layer. On the other hand, the heat treatment temperature also affected to correlated color temperature (CCT) and color rending index (CRI). The color conversion component with a green (lower) - red (upper) layer which was sintered at $550^{\circ}C$ showed the best optical properties: CCT, CRI and luminance efficacy were 3340 K, 78, and 56.5 lm/w, respectively.

• Journal of the Korean Ceramic Society
• /
• v.53 no.4
• /
• pp.381-385
• /
• 2016

Recently, white LEDs, especially, warm white LEDs have been intensively investigated due to outstanding optical properties, long term stability and low power consumption. In this study, mixed type and patterned type of remote phosphors were prepared by screen printing process employing green and red phosphor. Each type of remote phosphor exhibited distinctive photoluminescence spectrum. For example, the mixed type of remote phosphor exhibited unique spectrum, while the patterned type showed expectable spectrum depending on the concentration of phosphors. This indicates that a small amount of red phosphor dramatically reduced the green photoluminescence in the case of mixed-type remote phosphor, whereas the effect was negligible in the patterned-type remote phosphor. The possibility of undesirable chemical reaction was further investigated by using scanning electron microscopy and X-ray diffraction.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.06a
• /
• pp.391-394
• /
• 1998

Electroluminescence is the light emission obtained by an electrical excitation energy passing through a phosphor under an applied high electrical field. EL are paid much attention on flat panel display as a backlight and indicator, which are divided into ACPRL(alternating-current powder electroluminescent) and ACTFEL(alternating-current powder electroluminescent). In this paper, Electric and emission properties on ACPEL are investigated based on ZnS:Cu phosphor. The basic structure on this is ITO glass/phosphor/insulator/ backelectrode, CR-M which has high efficiency on thermal properties and dielectric Properties was introduced and BaTiO$_3$ as a insulating layer in order to increase app1ied electric field on phosphor. Changing on Dielectric and emission Properties was caused by a different viscosity of binder which filled on space between phosphor particle. 60cd/$m^2$ under 60V, 2kHz sinusoidal was gotten from ACPELD prepared in this work.