• Journal of Pharmaceutical Investigation
• /
• 제37권4호
• /
• pp.243-247
• /
• 2007

Retinoids have many important and diverse functions and particularly, have been widely used as anti-aging agent and for the treatment of acne and psoriasis in cosmetics. However, retinoids have low stability against the air, light, water, oxygen and heat, thus, to stabilize the retinoids in formulations is very critical procedure. In this study, cubic liquid crystalline phase of monoolein was applied to stabilize the retinylpalmitate (RP) and to enhance the transdermal permeation. Cubic liquid crystalline phase significantly enhanced the stability of RP. After 15 days, the content of RP in the cubic formulation was 94.7% while the content of RP in ethanol solution was below 0.5% at room temperature. Although BHT containing crystalline phase showed the slightly increased stability of RP, there were no significant differences in RP stability between with or without antioxidants (ascorbic acid, ${\alpha}$-tocopherol, BHT, BHA) at $40^{\circ}C$. The skin retention of RP in crystalline formulations was approximately $5.3{\sim}6.4$ times greater than that of o/w cream formulation. Incorporation of RP into cubic liquid crystalline phase of monoolein effectively stabilized the RP and worked as excellent topical vehicle for RP. Liquid crystalline phase is considered to be suitable formulation for RP for topical delivery system as a stabilizer and permeation enhancing agent.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2009년 추계학술발표대회
• /
• pp.95-95
• /
• 2009

Zinc coatings provide the most effective and economical way of protecting steel against corrosion. There are three types of galvanizing lines typically used in production line in galvanizing industries,Galvanize (GI) coating (Zn-0.1-0.3%Al), Galfan coating (Zn-5%Al), Galvalume(GL) coating (45%Zn-Al). In continuous Galvanizing lines, the immersed bath hardware (e.g. bearings, sink, stabilizer, and corrector rolls, and also support roll arms and snout tip) are subjected to corrosion and wear failure. Understanding the reaction of these materials with the molten Zn alloy is becomes scientific and commercial interest. To investigate the reaction with molten Zn alloys, static immersion test performed for 4, 8, 16, and 24 Hr. Two different baths used for the static immersion, which are molten Zn and molten Zn-55%Al. Microstructures characterization of each of the materials and intermetallic layer formed in the reaction zone was performed using optical microscope, SEM and EDS. The thickness of the reaction layer is examined using image analysis to determine the kinetics of the reaction. The phase dominated by two distinct phase which are eutectic carbide and matrix. The morphology of the intermetallic phase formed by molten Zn is discrete phase showing high dissolution of the material, and the intermetallic phase formed by Zn-55wt%Al is continuous. Aluminum reacts readily with the materials compare to Zinc, forming iron aluminide intermetallic layer ($Fe_2Al_5$) at the interface and leaving zinc behind.

• 멤브레인
• /
• 제14권3호
• /
• pp.218-229
• /
• 2004

SPG (Shirasu porous glass) 관형 막이 설치된 회분식 막유화 장치를 사용하여 단분산 칼슘 알지네이트 미립자를 제조하기 위한 막유화 공정변수의 최적조건을 결정하였다. 막유화의 공정변수로는 연속상에 대한 분산상의 비율, 알지네이트 농도, 유화제의 종류와 농도, 안정제 농도, 가교제 농도, 교반속도, 막간 압력차 및 SPG 막의 세공크기로 설정하고, 이들 변수가 제조된 알지네이트 미립자의 입자 크기와 분포에 미치는 영향을 검토하였다. 막유화의 공정변수들 중에서 연속상에 대한 분산상의 비율, 막간 압력차 그리고 알지네이트 농도가 증가할수록 미립자의 크기가 증가하였다. 반면 유화제의 농도, 교반속도 그리고 가교제의 농도가 증가할수록 미립자의 크기가 감소하였다. 세공 크기 $2.9{\mu}\textrm{m}$인 SPG막을 사용한 경우 막유화의 공정변수 조절을 통해 최종적으로 평균 입자 크기 $6{\mu}\textrm{m}$, 크기 분산도 1.1인 단분산 알지네이트 미립자의 제조가 가능하였다.

• 열처리공학회지
• /
• 제18권2호
• /
• pp.91-98
• /
• 2005

Both commercially pure titanium and Ti-6Al-4V alloy have been widely used as biomaterials because of their excellent biocompatibility, corrosion resistance and mechanical properties. However, in recent years, vanadium has been found to cause cytotoxic effects and adverse tissue reactions, while aluminium has been associated with potential neurological disorders. A newly designed ${\alpha}+{\beta}$ type Ti alloy, Ti-10Ta-10Nb alloy showed superior properties to CP Ti and Ti-6Al-4V alloy in the point of biomaterial, and elucidated the future uses as a biomaterial. Microstructural changes of Ti-10Ta-10Nb alloy after hot-rolling, warm-rolling, solution and aging treatment were investigated. According to TEM results, the microstructures after solution treatment were composed of mostly ${\alpha}$ phase with a trace of ${\beta}$ phase due to adding ${\beta}$-phase stabilizer tantalum and niobium. The microstructures after warm-rolling is coarse and elongated ${\alpha}$ phase and hot rolling resulted in very fine ${\alpha}$ widmanst$\ddot{a}$tten. The highest value of hardness was obtained by aging treatment at $400^{\circ}C$ for 20hr in which microstructure consisted of very fine ${\alpha}$ phase in ${\beta}$ matrix.

• 멤브레인
• /
• 제31권1호
• /
• pp.52-60
• /
• 2021

SPG (Shirasu porous glass) 원통형 막을 회전 시키는 회전 막유화를 사용하여 칼슘 알지네이트 미소 구체를 제조할 때, 단분산 미소 구체를 제조하기 위한 회전 막유화 공정변수들의 최적 조건을 결정하였다. 회전 막유화의 공정 변수로는 막의 회전 속도, 막간 압력차, 연속상에 대한 분산상의 비율, 알지네이트 농도, 유화제의 농도, 안정제 농도, 가교제 농도 및 막의 세공 크기를 설정하고, 이들 변수로 제조된 알지네이트 미소 구체의 크기와 단분산성에 미치는 영향을 검토하였다. 이 결과 회전 막유화의 공정 변수들 중에서 막모듈의 회전 속도, 유화제의 농도, 가교제의 농도가 증가 할수록 미소 구체의 크기가 감소하였으며, 반면에 연속상에 대한 분산상의 비율, 막간 압력차, 알지네이트 농도가 증가할수록 미소 구체의 크기가 증가하였다. 세공 크기 3.2 ㎛인 SPG막을 사용한 회전 막유화에서 공정변수 조절을 통해 최종적으로 입자 크기가 4.5 ㎛의 단분산 알지네이트 미소 구체의 제조가 가능하였다.

• 전기화학회지
• /
• 제25권4호
• /
• pp.191-200
• /
• 2022

Na-β"-Al₂O₃ has been widely employed as a solid electrolyte for high-temperature sodium (Na) beta-alumina batteries (NBBs) thanks to its superb thermal stability and high ionic conductivity. Recently, a vapor phase conversion (VPC) method has been newly introduced to fabricate thin Na-β"-Al₂O₃ electrolytes by converting α-Al₂O₃ into β"-Al₂O₃ in α-Al₂O₃/yttria-stabilized zirconia (YSZ) composites under Na⁺ and O^2- dual percolation environments. One of the main challenges that need to be figured out is lowered conductivity due to the large volume fraction of the non-Na⁺-conducting YSZ. In this study, the effect of lithia addition in the β"-Al₂O₃ phase on the grain size and ionic conductivity of Na-β"-Al₂O₃/YSZ solid electrolytes have been investigated in order to enhance the conductivity of the electrolyte. The amount of pre-added lithia (Li₂O) precursor as a phase stabilizer was varied at 0, 1, 2, 3, and 4 mol% against that of Al₂O₃. It turns out that ionic conductivity increases even with 1 mol% lithia addition and reaches 67 mS cm^-1 at 350 ℃ of its maximum with 3 mol%, which is two times higher than that of the undoped composite.

• 분석과학
• /
• 제13권3호
• /
• pp.282-290
• /
• 2000

본 연구는 390nm 이하에서 자외선 흡수가 완벽한 폴리카보네이트(광학용)에 첨가된 각종 첨가제를 아세톤으로 추출하거나 용해-침전 방식으로 분리하여 분석하는 것이다. 분리된 첨가제를 정성적으로 분석하기 위해 자외선흡광광도계, FT-IR 및 HPLC로 분석하였다. 분리된 물질은 광안정제 및 산화방지제(1차 및 2차)등의 첨가제와 단량체 및 올리고머가 함유된 복잡한 혼합물로 추정할 수 있다. 분리된 첨가물을 Bondapak $C_{18}$ 칼럼, 메탄올 이동상, PDA (Photodiode Array) 검출기를 사용한 역상(reversed phase, RP) HPLC 분석을 통해 비스페놀 A, Irganox 1010, Cyasorb UV-5411 성분들을 확인할 수 있있다. 또한, 자외선 흡광도를 이용한 정량분석을 통해 폴리카보네이트에 광안정제인 Cyasorb UV-5411가 0.12중량% 함유된 것을 알 수 있었다.

• Food Science and Biotechnology
• /
• 제18권1호
• /
• pp.157-161
• /
• 2009

Resveratrol-loaded poly($\varepsilon$-caprolactone) (PCL) nanoparticles were prepared by oil in water (O/W) emulsion solvent evaporation method. The morphology of the nanoparticles was evaluated using atomic force microscope (AFM), in which well-shaped and rigid nanoparticles were prepared. The mean particle size of nanoparticles prepared using only dichloromethane (DCM) ($523.5{\pm}36.7\;nm$) was larger than that prepared with a mixture of DCM and either ethanol (EtOH) ($494.5{\pm}29.2\;nm$) or acetone ($493.5{\pm}6.9\;nm$). The encapsulation efficiency of nanoparticles prepared only with DCM as dispersed phase ($78.3{\pm}7.7%$) was the highest of those prepared with solvent mixtures. An increase in the molecular weight of PCL led to an increase in encapsulation efficiency (from $78.3{\pm}7.7$ to $91.4{\pm}3.2%$). Pluronic F-127 produced the smallest mean size ($523.5{\pm}36.7\;nm$) with the narrowest particle size distribution. These results show that dispersed phase, molecular weight of wall materials, emulsion stabilizer could be important factors to affect the properties of nanoparticles.

• 한국세라믹학회지
• /
• 제35권12호
• /
• pp.1294-1300
• /
• 1998

Yttria-stabilized zirconia ceramics with irregular grain shapes and curved grain boundaries was prepared by ceria doping. The amount of ceria doped into zirconia compacts by a dipping method were at range of 2 to 20 mol% Irregular grain shapes and curved grain boundaries were formed only inspecimens doped with more than 8mol% cerial. Ceria-doped specimens showed large grain size and low sintered density compared with pure yttria-stabilized zirconia which was due to the increase in the contents of stabilizer and cubic phase. The amount of doped ceria was larger on the surface than the inside regions and therefore mi-crostructure and phase on the surface were different from those in the inside regions. Transgranular frac-ture mode was observed ion ceria doped specimens due to irregular large grain sizes.

• Corrosion Science and Technology
• /
• 제9권2호
• /
• pp.98-103
• /
• 2010

In order to further reduce the cost without reducing the corrosion resistance, a high-manganese austenitic alloy for sink roll or stabilizer roll in continuous hot-dip coating lines was developed. A systematic study of corrosion behavior of the high-manganese austenitic alloy in pure zinc bath at $490^{\circ}C$ was carried out. The results shows that, the high-manganese austenitic alloy shows better corrosion resistance than 316L steel. The corrosion rate of the high-manganese austenitic alloy in pure zinc bath is calculated to be approximately $6.42{\times}10^{-4}g{\cdot}cm^{-2}{\cdot}h^{-1}$, while the 316L is $1.54{\times}10^{-3}g{\cdot}cm^{-2}{\cdot}h^{-1}$. The high-manganese austenitic alloy forms a three-phase intermetallic compound layer morphology containing ${\Gamma$}, ${\delta}$ and ${\zeta}$ phases, while the 316L is almost ${\zeta}$ phase. The ${\Gamma}$ and ${\delta}$ phases of the high-manganese austenitic alloy contain about 8.5 wt% Cr, the existence of Cr improve the stabilization of phases, which slow down the reaction of Fe and Zn, improve the corrosion resistance of the high-manganese austenitic alloy. So substitute the nickel with the manganese to manufacture the high-manganese austenitic alloy of low cost is feasible.