• Journal of Magnetics
• /
• 제2권3호
• /
• pp.76-85
• /
• 1997

Magnetic and magnetostrictive properties of Tb-Fe and Tb-Fe-B thin films are systematically investigated over a wide composition range from 40.2 to 68.1 at. % Tb. The films were fabricated by rf magnetron sputtering using a composite target which consists of an Fe plate and Tb chips. The microstructure, examined by X-ray diffraction, mainly consists of an amorphous phase and, at high Tb contents, a pure Tb phase also exists. A progressive change in the direction of anisotropy from the perpendicular to in-plane occurs as the Tb content increases and the boundary at which the anisotropy change occurs shifts significantly towards to higher Tb contents with the addition of B. The saturation magnetization exhibits maxima at the Tb contents of 42 and 48 at. % for Tb-Fe and Tb-Fe-B thin films, respectively, and it is decreased by the addition of B. The coercive force, measured in the easy direction, decreases monotonically with the Tb content. Excellent magnetostrictive characteristics, particularly at low magnetic fields, are achieved in both Tb-Fe and Tb-Fe-B thin films; for example, a magnetostriction of 138 ppm is obtained in a Tb-Fe-B thin film at a magnetic field as low as 30 Oe. The excellent magnetostrictive properties of the present thin films are supported by the equally excellent magnetic softness, the coercivity below 10 Oe and a typical squared-loop shape with the saturation field as low as 1 kOe. Due to the excellent low field magnetostrictive characteristics, the present Tb-Fe based thin films are thought to be suitable for Si based microdevices.

• Corrosion Science and Technology
• /
• 제3권5호
• /
• pp.198-208
• /
• 2004

Although there has been no general agreement on the mechanism of primary water stress corrosion cracking (PWSCC) as one of major degradation modes of Ni-base alloys in pressurized water reactors (PWR's), common postulation derived from previous studies is that the damage to the alloy substrate can be related to mass transport characteristics and/or repair properties of overlaid oxide film. Recently, it was shown that the oxide film structure and PWSCC initiation time as well as crack growth rate were systematically varied as a function of dissolved hydrogen concentration in high temperature water, supporting the postulation. In order to understand how the oxide film composition can vary with water chemistry, this study was conducted to characterize oxide films on Alloy 600 by an in-situ Raman spectroscopy. Based on both experimental and thermodynamic prediction results, Ni/NiO thermodynamic equilibrium condition was defined as a function of electrochemical potential and temperature. The results agree well with Attanasio et al.'s data by contact electrical resistance measurements. The anomalously high PWSCC growth rate consistently observed in the vicinity of Ni/NiO equilibrium is then attributed to weak thermodynamic stability of NiO. Redox-induced phase transition between Ni metal and NiO may undermine the integrity of NiO and enhance presumably the percolation of oxidizing environment through the oxide film, especially along grain boundaries. The redox-induced grain boundary oxide degradation mechanism has been postulated and will be tested by using the in-situ Raman facility.

• Transactions on Electrical and Electronic Materials
• /
• 제6권5호
• /
• pp.202-209
• /
• 2005

Phase evolution, microstructure and the electrical properties such as $k_p$ and $Q_m$ of $Pb(Mg_{1/3}Nb_{2/3})O_3[PMN]-Pb(Mn_{1/3}Nb_{2/3})O3[PM'N]-PbZrO_3[PZ]-PbTiO_3[PT]$ quaternary system were investigated within the compositional ranges $0{\leq}y{\leq}0.125$, y+z=0.125, and $0.39{\leq}x{\leq}0.54$ of the formula $Pb_{0.97}Sr_{0.03}[Mg_{1/3}Nb_{2/3})_y\;(Mn_{1/3}Nb_{2/3})_z\;(Zr_{x}Ti_{1-x})_{1-(y+z)}]O_3$. In the case of increasing Mn/(Mg+Mn) ratio for a fixed Zr/Ti ratio of 47.5/52.5, phase relation remained unchanged but the grain size drastically decreased, and the electrical properties changed as following: both $k_P$ and $Q_m$ reached the peak values at $Mn/(Mg+Mn)\cong0.3l7$ and gradually decreased; $\varepsilon33^T$ showed a monotonic decrease; P-E hysteresis loop gradually changed to asymmetrical one, and $E_i$ increased in correspondence. With increasing Zr/Ti ratio for a fixed Mn/(Mg+Mn) ratio of 0.317, on the contrary, the cell parameter $(\alpha^2c)^{1/3}$ gradually increased, and tetragonal-rhombohedral morphotropic phase boundary appeared in the range of $51/49{\leq}Zr/Ti{\leq}54/46$. the meantime, the grain size substantially increased, and the electrical properties changed as following: $k_P$ and $\varepsilon33^T$ reached peak values at Zr/Ti=51/49 and 48/52, respectively, and then gradually decreased; change of $Q_m$ was adverse to $k_P$; both $E_C\;and\;E_i$ considerably decreased while $P_S$ moderately increased. For the system 0.125(PMN+PM'N)-0.875PZT studied, the composition Mn/(Mg+Mn)=0.3l7 and Zr/Ti=51/49 revealed some promising electrical properties for piezoelectric transformer application such as $k_P=0.58,\;Q_m\cong1000$, and $\varepsilon^T_{33}=970$, as well as dense and fine-grained microstructure.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2010년도 추계학술대회 초록집
• /
• pp.75.2-75.2
• /
• 2010

Polymer electrolyte fuel cells (PEFCs) have received a lot of attention as a power source for both stationary and mobile applications due to their attractive feature. In general, the performance of PEFCs is highly affected by the property of the electrodes. A PEFC electrode essentially consists of a gas diffusion layer and a catalyst layer. The gas difusion layer is highly porous and hydrophobicized with PTFE polymer. The catalyst layer usually contains electrocatalyst, proton conducting polymer, even PTFE as additive. Particularly, the proton conducting ionomer helps to increase the catalytic activity at three-phase boundary and catalyst utilization. Futhermore, it helps to retain moisture, resulting in preventing the electrodes from membrane dehydration. The most widely used proton conducting ionomer is perfluorinated sulfonic acid polymer, namely, Nafion from DuPont due to its high proton conductivity and good mechanical property. However, there are great demands for alternative ionomers based on non-fluorinated materials in terms of high temperature availability, environmental adaptability and production cost. In this study, the electrodes with the various content of the sulfonated poly(ether sulfone) ionomer in the catalyst layer were prepared. In addition, we evaluated electrochemical properties of the prepared electrodes containing the various amount of the ionomers by using the cyclic voltammetry and impedance spectroscopy to find an optimal ionomer composition in the catalyst layer.

• 한국분말재료학회지
• /
• 제21권5호
• /
• pp.349-354
• /
• 2014

This study is a basic research for repair material production which manufactured a Cu repair coating layer on the base material of a Cu plate using kinetic spray process. Furthermore, the manufactured material underwent an annealing heat treatment, and the changes of microstructure and macroscopic properties in the Cu repair coating layer and base material were examined. The powder feedstocks were sphere-shaped pure Cu powders with an average size of $27.7{\mu}m$. The produced repair coating material featured $600{\mu}m$ thickness and 0.8% porosity, and it had an identical ${\alpha}$-Cu single phase as the early powder. The produced Cu repair coating material and base material displayed extremely high adhesion characteristics that produced a boundary difficult to identify. Composition analysis confirmed that the impurities in the base material and repair coating material had no significant differences. Microstructure observation after a $500^{\circ}C/1hr$. heat treatment (vacuum condition) identified recovery, recrystallization and grain growth in the repair coating material and featured a more homogeneous microstructure. The hardness difference (${\Delta}H_v$) between the repair coating material and base material significantly reduced from 87 to 34 after undergoing heat treatment.

• 전기학회논문지
• /
• 제57권7호
• /
• pp.1213-1217
• /
• 2008

Poling is an important process in fabricating PZT ceramic devices such as filters and resonators and activates piezoelectricity to sintered PZT ceramics. Tolerance of the operating frequency of these devices is tightly required in applications. And a factor to attribute the tolerance is the temperature dependence of the resonance frequency of PZT ceramics. In this paper the relationship of poling strength and temperature dependence of resonance frequency of PZT specimens was studied. The $Pb(Zr_{0.53}Ti_{0.47})O_3$ ceramics were fabricated and the poling strengths were chosen to be 0.5, 1.5, 2.5 and 3.5 [kV/mm]. The dielectric constant of the specimen poled in poling strength 0.5 [kV/mm] was less than that of unpoled specimen and the specimen poled in higher electric field had the higher dielectric constant. (002) peak in X-ray diffraction patterns of the specimens increased as poling strength increased. And the change of resonance frequency of the specimens according to the variation of temperature was measured. Resonance frequency of all specimens increased as the temperature increased. The specimen poled in higher electric field had the smaller positive temperature coefficient of resonance frequency. The effect that temperature coefficient of resonance frequency becomes smaller is obtained when Zr mole in PZT composition equation increase. Controlling the poling strength is believed to be a method to adjust the temperature stability of resonance frequency of the PZT ceramic devices.

• 한국전기전자재료학회논문지
• /
• 제20권2호
• /
• pp.124-129
• /
• 2007

Dielectric and piezoelectric properties of $0.57Pb(Sc_{1/2}Nb_{1/2})O_{3}-0.43PbTiO_{3}$, which is the morphotropic phase boundary composition for the PSN-PT system, were investigated as a function of $Fe_{2}O_{3},\;Nb_{2}O_{5}\;and\;MnO_{2}$ addition 0 wt% to 0.9 wt%. The maximum dielectric constant of ${\varepsilon}_{33}/{\varepsilon}_{o}=2054$ and the minimum dielectric loss of $tan{\delta}=0.37\;%$ at room temperature were obtained at 0.1 wt% of $Fe_{2}O_{3}$ and 0.5 wt% of $MnO_{2}$ addition, respectively. With addition of 0.5 wt% $Nb_{2}O_{5}$ and $0.5\;wt%\;MnO_{2}$, the electromechanical coupling factor $k_{p}$ and mecanical quality factor $Q_{m}$ were significantly increased, respectively. The maximum electromechanical coupling factor $k_{p}=61.5\;%$ was obtained by addition of $Nb_{2}O_{5}$ and high mechanical quality factor $Q_{m}=919$ was obtained by addition of $MnO_{2}$. The $Q_{m}(=919)$ value is 3.3 times larger than that of non-doped 0.57PSN-0.43PT ceramics.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 하계학술대회 논문집 Vol.9
• /
• pp.310-310
• /
• 2008

본 연구에서는 (1-x) Pb(Zr0.515Ti0.485)$O_3$ - x Pb$(Sb_{1/2}Nb_{1/2})O_3$ + 0.5wt% $MnO_2$ 조성에 Pb$(Sb_{1/2}Nb_{1/2})O_3$ (PSN) (x=0.02, 0.04, 0.06, 0.08) 변화에 따른 미세구조 및 압전, 유전특성에 관해 고찰하였다. PSN 치환량이 증가함에 따라 정방정 (tetragonal)구조에서 삼방정(rhombohedral)구조로 상전이가 일어났으며, 결정립의 크기가 작아지는 것을 확인하였다. 전기기계결합계수 (kp) 는 PSN이 4 mol % 치환됨에 따라 증가하였으며, 더 이상 치환 시 감소하였다. PSN 치환에 따른 전기적 특성은, 결정구조, 결정립의 크기 및 2 차상 등의 미세구조와 긴밀한 관계가 있는 것으로 보여진다. 상경계(Morphotropic Phase Boundary) 영역인 0.96 Pb(Zr0.515Ti0.485)$O_3$ - 0.04 Pb$(Sb_{1/2}Nb_{1/2})O_3$ + 0.5wt% $MnO_2$ 조성에서 $\varepsilon{^T}_{33}/\varepsilon_o$ = 1109, $k_p$= 70.8 (%), $d_{33}$= 325 (pC/N)의 우수한 특성을 나타내었다.

• 한국세라믹학회지
• /
• 제45권4호
• /
• pp.220-225
• /
• 2008

Lead-free ferroelectric ceramics are widely researched today for industrial applications as sensors, actuators and transducers. Since $Pb(Zr_aTi_{1-a})O_3$-(PZT) has high Curie temperature($T_C$), high piezoelectric properties near its morphotropic phase boundary(MPB) composition and small temperature dependence electrical behavior, it has been used to commercial materials for wide temperature range and different application fields. According to the tolerance factor concept, since the $Bi^{3+}$ cation with 12-fold coordinate has a smaller ionic radius than 12-fold coordinate $Pb^{2+}$, most bismuth based perovskites possess a smaller tolerance factor. Therefore, MPBs with a higher $T_C$ may be expected in $Bi(Me^{3+})O_3PbTiO_3$ solid solutions. As in lead based perovskite systems, it is clear that we need to explore more materials in simple or complex bismuth based MPB systems. The objective of this study is to investigate the $Bi(Ni_{1_a}X_a)O_3-PbTiO_3(X=Ti^{4+},\;Nb^{5+})$ perovskite solid-solution. For improving the electronic conduction problem, the magnesium and manganese modified system was also studied.

• 한국재료학회지
• /
• 제15권7호
• /
• pp.453-457
• /
• 2005

Piezoelectric properties of $Pb(Mn_{1/3}Nb_{2/3})O_3-PbZrO_3-PbTiO_3$ ceramics were investigated with $Al_2O_3$ content $(0.0-1.0 wt\%)$. The constituent phases, microstructure, electromechanical coupling factor, dielectric constant, piezoelectric charge and voltage constants were analyzed. Diffraction peaks for (002) and (200) planes were identified by X-ray diffractometer for all the specimens doped with $Al_2O_3$, indicating the MPB (morphotropic phase boundary) composition of tetragonal structures. The highest sintered density of $7.8 g/cm^3$ was obtained for $0.2wt\%\;Al_2O_3-doped$ specimen. Grain size increased by doping $Al_2O_3$ up to $0.3 wt\%$, and it decreased by more doping. Electromechanical coupling factor, dielectric constant, piezoelectric charge and voltage constants increased by doping $Al_2O_3$ up to $0.2wt\%$, and it decreased by more doping. This might result from the formation of oxygen vacancies due to defects in $O^{2-}$ ion sites and the substitution of $Al^{3+}$ ions.