• Journal of the Korean Institute of Gas
• /
• v.12 no.3
• /
• pp.7-12
• /
• 2008

In this study, a spark ignition engine operated with the DME blended LPG fuel was investigated experimentally. Performance, emissions characteristics including hydrocarbon, CO, NOx, and combustion stability of an SI engine fuelled with DME blended LPG fuel were examined at $1200{\sim}5200\;rpm$. Results showed that stable engine operation was possible for a wide range of engine loads within 20% mass content of DME fuel. Also, engine output power within 10% mass content of DME fuel was comparable to that of pure LPG fuel operation. However, engine output power was decreased and break specific fuel consumption (BSFC) was severely increased with the amount of blended fuel as the energy content of DME was much lower than that of LPG. DME blended LPG fuel is expected to be potential for enlarging DME market.

• Journal of the Korean Institute of Gas
• /
• v.13 no.6
• /
• pp.39-43
• /
• 2009

Gasoline engine have proved its utility in light, medium and heavy duty vehicle in every sector of the world community. The concern about long term availability of petroleum and the increasing threat for the environment by the increasing load of vehicular emission, compel the technology to upgrade itself for meeting the challenges. CNG is environmentally clean alternative to the existing SI Engines with out much change in the hardware. Many researchers have found this as a potential substitute to meet the energy requirement. Higher octane number and higher self ignition temperature make it a good gaseous fuel. Although power output is slightly lesser than the gasoline it's thermal efficiency is better than the gasoline for the same SI Engine. Results showed that reduced CO, hydrocarbon emissions is a favorable outcome, with slight increase in NOx emission when compared with gasoline fuel to dual fuel mode in the existing SI Engines.

• Korean Journal of Food Science and Technology
• /
• v.6 no.4
• /
• pp.219-230
• /
• 1974

For the production of single cell protein from n-paraffin, yeasts utilizing n-paraffin and ethanol were isolated from oil deposit and oil field soils. The mixed cultivation between yeasts assimilating n-paraffin and ethanol was carried out to increase cell yield. Finally, selected strains were identified and suitable medium composition for mixed culture was compared with that of single cultures using flask and 5 l-jar fermentor. Yeasts grow on n-paraffin and ethanol were identified as Candida tropicalis var. KIST 76 and Trichosporon cutaneum KIST 76H respectively. By mixed cultivation under the suitable medium composition using 5 l-jar fermentor, maximum dry cell weight reached 20 g/l after 12 hrs. cultivation and it's protein content was 58%. Yield has been increased about 25% and protein content has been increased 6.7% compared to that of single culture, Candida tropicalis var. KIST 76, after 16 hrs. cultivation.

• Structural Engineering and Mechanics
• /
• v.59 no.1
• /
• pp.37-57
• /
• 2016

Reservoir geomechanics can play an important role in hydrocarbon recovery mechanism. In $CO_2$-EOR process, reservoir geomechanics analysis is concerned with the simultaneous study of fluid flow and the mechanical response of the reservoir under $CO_2$ injection. Accurate prediction of geomechanical effects during $CO_2$ injection will assist in modeling the Carbon dioxide recovery process and making a better design of process and production equipment. This paper deals with the implementation of a program (FORTRAN 90 interface code), which was developed to couple conventional reservoir (ECLIPSE) and geomechanical (ABAQUS) simulators, using a partial coupling algorithm. A geomechanics reservoir partially coupled approach is presented that allows to iteratively take the impact of geomechanics into account in the fluid flow calculations and therefore performs a better prediction of the process. The proposed approach is illustrated on a realistic field case. The reservoir geomechanics coupled models show that in the case of lower maximum bottom hole injection pressure, the cumulative oil production is more than other scenarios. Moreover at the high injection pressures, the production rates will not change with the injection bottom hole pressure variations. Also the FEM analysis of the reservoir showed that at $CO_2$ injection pressure of 11000 Psi the plastic strain has been occurred in the some parts of the reservoir and the related stress path show a critical behavior.

• Journal of Soil and Groundwater Environment
• /
• v.17 no.1
• /
• pp.13-21
• /
• 2012

This study reports a surfactant-enhanced in-situ remediation treatment at a test site which is located in a hilly terrain. The leakage oils from a storage tank situated on the top of the hill contaminated soils and groundwater in the lower elevation. Sixteen vertical injection wells (11 m deep) were installed at the top of the hill to introduce 0.1-0.5 vol.% of non-ionic Tween-80 surfactant. The contaminated area that required remediation treatment was about $1,650\;m^2$. Two cycles of injecting surfactant solution followed by water were repeated over approximately 7.5 months: first cycle with 0.5 month of surfactant injection followed by 3 months of water injection, and second cycle with 1 month of surfactant followed by 3 months of water injection. The seasonal fluctuation in groundwater table was also considered in the selection of periods for surfactant and water injection. The results showed that the initial Total Petroleum Hydrocarbon (TPH) concentration of 1,041 mg/kg (maximum 3,605 mg/kg) was reduced significantly down to 76.6 mg/kg in average. After 2nd surfactant injection process finished, average TPH concentration of soils was reduced to 7.5% compared to initial concentration. Also, average BTEX concentration of soils was reduced to 10.8%. This resultes show that the surfactant enhanced in-situ remediation processes can be applicable to LNAPL contaminated site in field scale.

• Korean Chemical Engineering Research
• /
• v.57 no.4
• /
• pp.455-460
• /
• 2019

Hydrotreating catalysis refers to a various hydrogenation which saturate an unsaturated hydrocarbon, together with removing heteroatoms such as sulfur, nitrogen, oxygen, and trace metals from different petroleum streams in a refinery. Most refineries include at least three hydrotreating units for upgrading naphtha, middle distillates, gas oils, intermediate process streams, and/or residue. Among them, hydrotreating catalysis for residue are the core of the process, because of its complexity. This article reviews recent progress in tackling the issues found in the upgrading residues by hydrotreating, focusing on the chemistry of hydrodemetallization (HDM) and hydrodesulfurization (HDS). We also discuss the composition and functions of hydrotreating catalysts, and we highlight areas for further improvement.

• Journal of the Korean Society of Mineral and Energy Resources Engineers
• /
• v.55 no.6
• /
• pp.660-669
• /
• 2018

Enhanced oil recovery (EOR) is a method used to improve the recovery factor of remaining hydrocarbon in reservoir. Polymer and surfactant EOR techniques have limitations depending on reservoir or production conditions (temperature, salinity, etc.) because the polymer and surfactant are highly affected by the reservoir conditions. In this study, analysis of the current improvements to chemical substances and application technologies was performed based on recent research data. Conventional polymer is readily degraded by the conditions of high temperature and high salinity. Therefore, new polymers and injection techniques have been developed to remediate such problems. In addition, surfactant applicable to shale and carbonate reservoirs is developed as petroleum recovery expands to unconventional reservoirs. However, these chemical substances are not widely used in the current oil fields due to high costs. Therefore, further studies must be conducted to reduce the cost and thus increase the effectiveness of EOR techniques.

• Journal of the Korean Geotechnical Society
• /
• v.22 no.7
• /
• pp.45-54
• /
• 2006

Resistivity cone penetrometer test (RCPT) can be employed at a relatively low cost for in-situ delineation of subsurface contamination. While the resistivity measurement has a potential to investigate the subsurface contamination, resistivity measurements alone will lead to some degree of ambiguity in the results. In this study, capacitance measurement was incorporated into the RCPT to overcome the ambiguity inherent in electrical resistivity measurements. This study is focused on verifying the applicability of resistivity and capacitance measurements of CPT module to provide information on subsurface contaminated by heavy metal and petroleum hydrocarbon. Laboratory model tests were performed to evaluate the sensitivity of the measured resistivity and relative capacitance on the water content and different types of contaminants. Test results show that simultaneous measurement of electrical resistivity and capacitance can give more reliable information on subsurface contamination. Electrical measurements of the CPT module showed high applicability to be used in detecting saturated soils contaminated by heavy metal and diesel plume floating above the groundwater table.

• Journal of Environmental Impact Assessment
• /
• v.29 no.3
• /
• pp.157-181
• /
• 2020

Sediments from rivers, lakes and marine ports serve as end points for pollutants discharged into the water, and at the same time serve as sources of pollutants that are continuously released into the water. Until now, the contaminated sediments have been landfilled or dumped at sea. Landfilling, however, was expensive and dumping at sea was completely banned due to the London Convention. Therefore, this study applied contaminated sedimentation soil of 'Royal Palace Livestock Complex' as soil purification method. Soil remediation methods were applied to pretreatment, composting, soil washing, electrokinetics, and thermal desorption by selecting overseas application cases and domestically applicable application technologies. As a result of surveying the site for pollutant characteristics, Disolved Oxigen (DO), Suspended Solid (SS), Chemical Oxygen Demand (COD), Total Nitrogen (TN), and Total Phosphorus (TP) exceeded the discharged water quality standard, and especially SS, COD, TN, and TP exceeded the standard several tens to several hundred times. Soil showed high concentrations of copper and zinc, which promote the growth of pig feed, and cadmium exceeded 1 standard of Soil Environment Conservation Act. In the pretreatment technology, hydrocyclone was used for particle size separation, and the fine soil was separated by more than 80%. Composting was performed on organic and Total Petroleum Hydrocarbon (TPH) contaminated soils. TPH was treated within the standard of concern, and E. coli was analyzed to be high in organic matter, and the fertilizer specification was satisfied by applying the optimum composting conditions at 70℃, but the organic matter content was lower than the fertilizer specification. As a result of continuous washing test, Cd has 5 levels of residual material in fine soil. Cu and Zn were mostly composed of ion exchange properties (stage 1), carbonates (stage 2), and iron / manganese oxides (stage 3), which facilitate easy separation of contamination. As a result of applying acid dissolution and multi-stage washing step by step, hydrochloric acid, 1.0M, 1: 3, 200rpm, 60min was analyzed as the optimal washing factor. Most of the contaminated sediments were found to satisfy the Soil Environmental Conservation Act's standards. Therefore, as a result of the applicability test of this study, soil with high heavy metal contamination was used as aggregate by applying soil cleaning after pre-treatment. It was possible to verify that it was efficient to use organic and oil-contaminated soil as compost Maturity after exterminating contaminants and E. coli by applying composting.

• Analytical Science and Technology
• /
• v.11 no.1
• /
• pp.62-72
• /
• 1998

This study was performed to characterize the trace organic pollutants in the industrial wastewater and to establish the database of the trace organic pollutants. The four manufacturing industries, which are refined petroleum, industrial chemicals, rubber & plastics and fabricated metals, were surveyed. The wastewater and discharging water of these 30 factories are analyzed to characterize the trace organic pollutants. In industrial chemicals, the kinds of products and organic pollutants are very various. Therefore to select the characteristic organic pollutants in this categories are also very difficult. In industrial chemicals, the gas chromatograpic peak patterns of wastewater are represented the various type according to their products, therefore the typical patterns of the characteristic organic pollutants could not be obtained because the kinds of manufactured goods and organic pollutants are very various. In refined petroleum, the effluent is discharged in the distillatory process of atmosphere pressure and contained the saturated hydrocarbons, phenol compounds, benzene compounds and naphtalene compounds. The saturated hydrocarbons peaks from $C_{15}$ to $C_{35}$ are represented the typical oil patterns by the uniform intervals therefore the peak can be easily distinguished. In rubber & plastics, the wastewater is discharged in the washing process which contains the additives. The problem of wastewater is not serious because the manufacturing process is not produced the effluent or the produced cooling water is recycled in that process.