• 한국군사과학기술학회지
• /
• 제12권2호
• /
• pp.170-174
• /
• 2009

This paper describes the wireless communication test environment for the Link-K system and shows the performance analysis of multiple access protocols. The test environment consists of data generator, modem, radio sets, attenuators, and antennas. In case of both CSMA and Roll-Call protocols, throughput performance and delay are measured. And test results are analyzed. The test results would be used for communication performance analysis and network design of Link-K system.

• 한국자동차공학회논문집
• /
• 제12권1호
• /
• pp.1-9
• /
• 2004

The general method which changes sub-cooling of refrigerant is to control the expansion valve in the state of mixing with liquid and gas phase. In this study, the performance of vehicle air conditioning system is to control either changing the expansion valve or adding the sub condenser. Therefore, this research finally is tested in case of the fourth test procedure, the second test was suitable for a valve opening area due to adjusting valve slope in comparison with the other test. The other test except for the second test happened to do liquid back due to the excessively liquified refrigerant into the system. In conclusion, the second test was appeared not to be influenced upon liquid back, and it is to expect positive performance by controlling an expansion valve. Therefore, it will be also useful to research for an increase of compressor efficiency Performance improvement of an air conditioner is to reinforce the suction performance of the evaporator and increase the sub-cooling, which make use of the sub-cooling system.

• 시스템엔지니어링학술지
• /
• 제15권2호
• /
• pp.9-16
• /
• 2019

The most important task in acquiring the weapon system is to determine the required performance and to test & evaluate it. The importance of the weapon system by ROC (Required Operational Capability) is not considered, and system development and test evaluation are carried out. In addition, technical incidental performance is tested on the same basis as ROC in the test evaluation and determined according to the result. Development test and evaluation that evaluates technical ability is very important, but development agency is supervised and performed. In this paper, we propose a method to give weights considering the importance of ROC, a technical incidental performance determination and test procedure, and a improvement plan for the development and operational test & evaluation.

• 전기학회논문지
• /
• 제56권2호
• /
• pp.325-333
• /
• 2007

A PV system inverter test module using RTDS was developed and performance test of a commercial PV inverter was carried out. The developed module consists of one RTDS hardware rack, RTDS software models representing PV array and simple distribution system, and two power amplifiers that was specifically designed for generating power corresponding to signals from RTDS. Performance test results verified effectiveness and reliability of the test module. It is expected that the developed test module may help PV inverter manufacturers improve ana test their systems in the developing stage.

• 설비공학논문집
• /
• 제15권2호
• /
• pp.132-136
• /
• 2003

For the study of performance evaluation on different shape heat exchangers that have the same energy consumption in a refrigerator, we make performance evaluation coefficient (PEC) which can distinguish performance of different shape heat exchangers. The results were reported in order to compare with for the dry frosting and wet frosting test as various definition of PECs. Results showed that PEC of dry frosting test is higher than that of wet frosting test because attached water droplet increases pressure drop of air-side then this decreases performance of heat exchanger.

• Tribology and Lubricants
• /
• 제25권3호
• /
• pp.187-191
• /
• 2009

A leakage performance test and an endurance performance test of a 75 ton class turbopump mechanical face seal are performed using water under high speed and high temperature environment. A prototype mechanical face seal is manufactured for the purpose of sealing of fuel between a fuel pump and turbine. By simulating operating condition experimentally, the leakage rate and seal carbon wear rate are obtained to evaluate the performance of the prototype mechanical face seal. The test results show the acceptable leakage performance and reasonable wear tendency as well.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2017년도 제48회 춘계학술대회논문집
• /
• pp.587-590
• /
• 2017

마이크로 가스터빈엔진의 성능 실험연구를 수행하였다. 성능측정을 위하여 마이크로엔진에 적합한 시험장치를 구축하였으며, Olympus HP Engine을 이용하여 성능측정을 수행하였다. 엔진흡입 공기유량, 추력, 연료소모율, 각 구성품 입구에서의 공기 및 가스온도를 측정하였다. 측정된 결과부터 마이크로 가스터빈 엔진의 성능특성을 보다 잘 이해할 수 있었다.

• 한국소음진동공학회논문집
• /
• 제16권8호
• /
• pp.857-863
• /
• 2006

This paper described the performance test and sound characteristics of helicopter 'Tail-Fan' anti-torque system. In this research, Korea Aerospace Research Institute(KARI) developed 'Tail-Fan' anti-torque system for a helicopter and carried out performance and sound capturing tests of even and uneven tail fans. The performance test is carried out and the noise signals which are generated during the test are saved with microphones at the same time. The performance test's results meet the design requirements. Tone-corrected perceived noise level is reduced by replacing the even product with the uneven one.

• 항공우주기술
• /
• 제4권2호
• /
• pp.50-59
• /
• 2005

본 연구에서는 개발된 테일팬 1차 시제품의 성능시험에 대한 것이다. 한국항공우주연구원에서는 헬리콥터용 반 토오크 시스템으로 테일팬 시스템을 개발하였으며, 제작된 1차 시제품의 성능시험을 위해 테일팬 성능시험장치를 제작하였다. 테일팬 성능시험을 위해 먼저 시험장치에 대한 제작 검증용 시험을 수행하였고, 다음으로 팬블레이드와 시험장치의 고유진동수를 확인하였다. 성능 시험용 시험장치 운용회전수를 결정하기 위한 운용시험을 수행하였다. 테일기어박스(TGB)에 가속도계를 부착하여 단계적으로 회전수와 부착물들을 변화시켜가며 고유진동수와 진동 레벨을 확인하였다. 운용시험 결과로부터 테일팬 성능시험용 시험장치 운용회전수를 결정하였고, 무풍조건과 비행 조건에 따른 성능시험을 수행하였다. 측정된 데이터는 무차원화하여 분석하였고, 이 결과로 개발 시제품이 성능 요구조건을 만족시킴을 확인할 수 있었다.

• 디지털콘텐츠학회 논문지
• /
• 제19권4호
• /
• pp.801-808
• /
• 2018

유선 네트워크를 구성하는 스위치나 라우터 또는 통합망에 대한 성능 시험방법론에 대해서는 아직 명확히 정의 되어 있지 않다. 스마트 폰과 멀티미디어 트래픽으로 인해 네트워크의 속도는 100Gbps까지 빠르게 증가하고 있다. 그러나, 정형화된 시험 방법이 없고 성능 시험 관련 부분은 아직도 옛날 자료를 기반으로 시험을 수행하고 있다. 통신사업자나 기업에서는 요구사항에 대한 시험을 자체 BMT(Benchmark Test)로 진행하고 있으며, 정부 또는 공공기관에서는 외부 기관에 성능 시험을 의뢰하고 있다. 차세대 네트워크 장비를 포함한 단위장비 및 통합망에 대한 성능 시험 수요가 증가함에 따라 성능 시험 방법에 대한 분석이 조속히 이루어져야 한다. 따라서 본 논문에서는 기관에서 수행하는 성능 시험 방법을 분석하고 모든 유선 네트워크 장비에 적용할 수 있는 가이드라인을 제시하고자 한다.