• Journal of Energy Engineering
• /
• v.15 no.1 s.45
• /
• pp.8-13
• /
• 2006

The oxidation behavior of $UO_2$, pellet was studied using an XRD and a thermogravimetric analyzer in the temperature range from 573 to 873 K and in the density range from 94.64 to 99.10% of theoretical density in air. It was found from the XRD study that $UO_2$ was completely converted to $U_3O_8$ in this experimental temperature range. The formation of $U_3O_8$ displays sigmoidal reaction kinetics. The oxidation rate was reduced with density. Induction time for the oxidation of $UO_2$ was delayed with density because of open pore formed in surface of $UO_2$ pellet. The activation energy for oxidation of $UO_2$ was determined to be 89.54 kJ/mol and 34.40 kJ/mol in the temperature range from 573 to 723 K and from 723 to 873 K, respectively.

• Journal of the Korean Ceramic Society
• /
• v.31 no.6
• /
• pp.637-642
• /
• 1994

Using SHS(Self-propagating High-temperature Synthesis) method, the optimum synthetic condition of titanium carbonitride was established by controlling the parameters such as relative density of mixture (Ti+C), nitrogen pressure, additive amounts of titanium hydride(TiH1.924) and protecting heat loss. Under 1 atm nitrogen pressure, nitridation ratio with changing relative density of the sample compacts has a maximum (87.2%) at about 55%, and in the case of enveloping the pellet with a quartz tube, the highest nitridation ratio of 90% was obtained at about 68%. At relative density of 55%, nitridation ratio with the nitrogen pressure has a miximum (87.3%) at 7 atm. As the amounts of additive titanium hydride increased, nitridation ratio decreased at below 7 atm nitrogen pressure and, increased at above this pressure until percent of addition percent reached 15 wt% and decreased abruptly upon futher increases in titanium hydride. In the synthesis of TiCxNy by combustion reaction, heat transfer from combustion zone to preheating zone and nitrogen gas penetration into the compact were found to be important factors affecting the TiCxNy formation. It was difficult to obtain high nitridation ratio when the conbustion temperature was either too high or too low, and it seems that the retention of high temperature after a combustion wave sweeped through the reactant mixture pellet is critical to obtain a satisfactory nitridation ratio.

• The Journal of Internal Korean Medicine
• /
• v.21 no.5
• /
• pp.781-789
• /
• 2000

Objective : The purpose of these research was to investigate effects of water extract of Bistortae Rhizoma(BRE) on the hemostasia, anti-inflammatory action and central nervous system. Methods : we used mice and rats administered with the extract of the above herbs. Results : BRE decreased the permeability of evans blue into peritoneal cavity and cotton pellet granuloma formation. BRE did not decrease the acetic acid induced writhing syndrome and the histamine induced mouse paw edema. BRE inhibited the pentylenetetrazole and the strychnine induced convulsion. BRE shortened the bleeding time and plasma prtrombin time. BRE did not affect on the proliferation of Balb/c 3T3 cells. Conclusions : these results suggest that the effects of BRE are the hemostasia, anti-inflammatory action, and mild depressant activity of central nervous system.

• Nuclear Engineering and Technology
• /
• v.31 no.6
• /
• pp.608-617
• /
• 1999

The powder mixture which has a bimodal size distribution, with a large mode corresponding to AUC-UO$_2$ powder and a small one corresponding to ADU-UO$_2$ powder, was prepared, pressed into compacts, and sintered at 1680t for 4 hours in hydrogen gas. The compact density of the powder mixture increases with increasing ADU-UO$_2$content within a content of 20 wt %, since small ADU-UO$_2$ particles can fill interstices between large AUC-UO$_2$particles. The UO$_2$ pellet made using the powder mixture has a lower open porosity than that made using AUC-UO$_2$ powder alone. The mechanism for the formation of a flake-like pore is proposed, and the decrease in open porosity may be ascribed to the decrease in the number of flake-like pores.

• Nuclear Engineering and Technology
• /
• v.50 no.2
• /
• pp.259-267
• /
• 2018

Focused ion beam-scanning electron microscope and electron backscattered diffraction examinations were conducted in the center of a $73\;GWd/t_U\;UO_2$ fuel. They showed the formation of subdomains within the initial grains. The local crystal orientations in these domains were close to that of the original grain. Most of the fission gas bubbles were located on the boundaries. Their shapes were far from spherical and far from lenticular. No interlinked bubble network was found. These observations shed light on previous unexplained observations. They plead for a revision of the classical description of fission gas release mechanisms for the center of high burn-up $UO_2$. Yet, complementary detailed observations are needed to better understand the mechanisms involved.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.5 no.1
• /
• pp.53-64
• /
• 2007

The dynamic release behavior of Cs from high burn-up spent PWR fuel was experimentally performed under the conditions of a thermal treatment process such as voloxidation and sintering conditions. In voloxidation process, influence of the oxidation and reduction atmosphere on the Cs release characteristic using fragment type of spent fuel heated up to $1,500^{\circ}C$ was compared. In sintering process, temperature history effect on Cs release behavior was evaluated using green pellet under 4% $H_2/Ar$ environment. Temperature range for complete Cs release from spent fuel fragment under voloxidation condition was about $800^{\circ}C{\sim}1,200^{\circ}C$, but that of green pellet under the reduction atmosphere was $1,100^{\circ}C{\sim}1,400^{\circ}C$. Key parameters on Cs release behavior from spent fuel was powder formation as well as the diffusion rate of Cs compound to grain boundary and fuel surface.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.15 no.4
• /
• pp.343-353
• /
• 2017

Processing and equipment were tailored for engineering scale fabrication of $UO_2$ porous pellets, a feed material for the electrolytic reduction process in the PRIDE (PyRoprocessing Integrated DEmonstration) facility at KAERI (Korea Atomic Energy Research Institute). The starting materials, $UO_2$ powder and pre-milled surrogate oxide powders, were proportioned to simulate the chemical composition of spent fuel (so-called Simfuel). The Simfuel powders were homogenized by mixing, compacted into a pellet shape, and finally heat treated using a tumbling mixer, rotary press, and sintering furnace. After sintering at $1450^{\circ}C$ for 24 h in $4%\;H_2-Ar$, the average bulk density of the $UO_2$ Simfuel pellets was $6.89g{\cdot}cm^{-3}$, which meets the standard of the following electrolytic reduction process. In addition, the results of a microstructural analysis demonstrated that the sintered Simfuel $UO_2$ porous pellets accurately simulate the properties of spent fuel in terms of the formation of second phases. These results provide essential information for the massive fabrication of $UO_2$ porous pellets for engineering scale pyroprocessing research.

• Journal of Pharmaceutical Investigation
• /
• v.27 no.4
• /
• pp.253-263
• /
• 1997

To investigate the interaction of omeprazole (OMP) and meglumine (MEG), a complex was prepared by freeze-drying method in ammoniacal aqueous medium at room temperature and subjected to IR, DSC, and 1H NMR analysis. In addition, the stability of the complex was tested by accelerated stability analysis, and the dissolution rate of both powder and enteric coated was determined pellet by paddle method. The results are as follows; i) IR, DSC, and $^{1}H$ NMR studies indicate the formation of inclusion complex between OMP and MEG probably by electrostatic forces as $[OMP]\;[MEGH]^+$ form in a stoichiometric ratio (1:1) of OMP : MEG. ii) The dissolution rate of enteric coated OMP-MEG complex pellet in simulated enteric fluid was 90.6% in 10 minutes, which may satisfy the requirement for the regulation of dissolution. iii) OMP-MEG complex were decomposed according to pseudo 1st order kinetics: while the decomposition of OMP showed a rate constant $(k_{25^{\circ}C})$ of $5.13{\times}10^{-4}{\cdot}\;day^{-1}$, a half-life$(t_{1/2})$ of 1,350 days, a shelf-life$(T_{90%})$ 205 days and an activation energy of 23.53 kcal/mole. OMP-MEG complex inhibited a rate $(k_{25})$ of $2.92{\times}10^{-4}{\cdot}\;day^{-1}$, a half-life$(t_{1/2})$ of 2,373 days, a shelf-life $(T_{90%})$ of 306 days and an activation energy of 20.18 kcal/mole. iv) OMP was stabilized markedly by the formation of OMP-MEG complex between OMP and MEG, and the humidity increased the stability of OMP-MEG complex by decreasing the decomposition rate$(k_{50^{\circ}C})$ from $1.27{\times}10^{-2}{\cdot}\;day^{-1}$ at 31% R.H. to $2.54{\times}10^{-2}{\cdot}\;day^{-1}$ at 90% R.H.

• Journal of the Korean Ceramic Society
• /
• v.40 no.12
• /
• pp.1213-1219
• /
• 2003

Porous ceramics for microoganism carriers were prepared with amorphous alumina and pore formers by hydrothermal reaction, burn-out and wash-out method. Activated carbon with average size of 67,222, and 405 $\mu\textrm{m}$, organic polymer and inorganic salt were used as pore formers. Specimens were hydrothermally treated at 200$^{\circ}C$ for 24 h, heat-treated at 650$^{\circ}C$ for 5 h, and washed out at 80$^{\circ}C$ for 48 h. The formation of crystalline phase, porosity, pore size distribution and compressive strength were measured. The specimen with activated carbon was transformed to boehmite phase, but organic polymer and inorganic salt inhibited the aquohydroxoy complex gel and crystalline formation. The porous ceramics for microoganism carriers using activated carbon as a pore formers was successfully prepared, which is composed of ${\gamma}$-alumina phase with porosity of above 70 vol% and the compressive strength of 40 kgf/$\textrm{cm}^2$.

• Korean Journal of Metals and Materials
• /
• v.50 no.9
• /
• pp.677-684
• /
• 2012

A feasible way to fabricate in-situ Al/TiC composites was investigated. An elemental mixture of $Al-TiO_2-C$ pellet was directly added into an Al melt at $800-920^{\circ}C$ to form TiC by self-combustion reaction. The addition of CuO initiates the self-combustion reaction to form TiC in $1-2{\mu}m$ at the melt temperature above $850^{\circ}C$. Besides the CuO addition, a diluent element of excess Al plays a significant role in the TiC formation by forming a precursor phase, $Al_3Ti$. Processing parameters such as CuO content, the amount of excess Al and the melt temperature, have affected the combustion reaction and formation of TiC, and their influences on the microstructures of in-situ Al/TiC composites are examined.