• Journal of Communications and Networks
• /
• v.12 no.6
• /
• pp.544-557
• /
• 2010

This paper addresses the problem of controlling the envelope's power peak of single carrier modulated signals, band limited by root-raised cosine (RRC) pulse shaping filters, in order to reduce power amplifier back-off for very small aperture terminals ground stations. Magnitude modulation (MM) is presented as a very efficient solution to the peak-to-average power ratio problem. This paper gives a detailed description of the MM concept and its recent evolutions. It starts by extending the look-up-table (LUT) based approach of the MM concept to M-ary constellations with M ${\leq}$ 16. The constellation and RRC symmetries are explored, allowing considerable reduction on LUT computation complexity and storage requirements. An effective multistage polyphase (MPMM) approach for the MM concept is then proposed. As opposed to traditional LUT-MM solutions, MM coefficients are computed in real-time by a low complexity multirate filter system. The back-off from high-power amplifier saturation is almost eliminated (reduction is greater than 95%) with just a 2-stage MPMM system even for very demanding roll-off cases (e.g., ${\alpha}$ = 0,1). Also, the MPMM is independent of modulation in use, allowing its easy application to constellations with M > 16.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.43 no.11 s.353
• /
• pp.98-104
• /
• 2006

The conventional burst-mode APC(Automatic Power Control) circuit had an effective structure that was suitable for a low power consumption and a monolithic chip. However, as data rate was increased, it caused errors due to the effect of the zero density. In this paper, we invented a new structured peak-comparator which could compensate the unbalance of the injected currents using double gated MOS and MOS diode. And we proposed a new burst-mode APC adopting it. The new peak-comparator in the proposed APC was very robust to zero density variations maintaining the correct decision point of the current comparison at high data rate. It was also suitable for a low power consumption and a monolithic chip due to lack of large capacitors.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.23 no.7
• /
• pp.67-74
• /
• 2009

This paper describes the speed control functions of the typical steam turbine speed controllers and the test results of generator load rejection simulations. The goal of the test is to verify the speed controller's ability to limit the steam turbine's peak speed within a predetermined level in the event of generator load loss. During normal operations, the balance between the driving force of the steam turbine and the braking force of the generator load is maintained and the speed of the turbine-generator is constant. Upon the generator's load loss, in other word, the load rejection, the turbine speed would rapidly increase up to the peak speed at a fast acceleration rate. It is required that the speed controller has the ability to limit the peak speed below the overspeed trip point, which is typically 110[%] of rated speed. If an actual load rejection occurs, a substantial amount of stresses will be applied to the turbine as well as other equipments, In order to avoid this unwanted situation, not an actual test but the other method is necessary. We are currently developing the turbine control system for another nuclear power plant and have plan to do the simulation suggested in this paper.

• Nuclear Engineering and Technology
• /
• v.50 no.6
• /
• pp.860-868
• /
• 2018

This article presents a new design of earthquake instrumentation that is suitable for quick decision-making after the seismic event at the nuclear power plant (NPP). The main objective of this work is to ensure more availability of the NPP by expediting walk-down period when the seismic wave is incident. In general, the decision-making to restart the NPP after the seismic event requires more than 1 month if an earthquake exceeds operating basis earthquake level. It affects to the plant availability significantly. Unnecessary shutdown can be skipped through quick assessments of operating basis earthquake, safe shutdown earthquake events, and damage status to structure, system, and components. Multidecision parameters such as cumulative absolute velocity, peak ground acceleration, Modified Mercalli Intensity Scale, floor response spectrum, and cumulative fatigue are discussed. The implementation scope on the field-programmable gate array platform of this work is limited to cumulative absolute velocity, peak ground acceleration, and Modified Mercalli Intensity. It can ensure better availability of the plant through integrated decision-making process by automatic assessment of NPP structure, system, and components.

• ETRI Journal
• /
• v.43 no.1
• /
• pp.7-16
• /
• 2021

Noncontiguous orthogonal frequency division multiplexing (NC-OFDM)-based cognitive radio (CR) systems achieve highly efficient spectrum utilization by transmitting unlicensed users' data on subcarriers of licensed users' data when they are free. However, there are two disadvantages to the NC-OFDM system: out-of-band power (OBP) and a high peak-to-average power ratio (PAPR). OBP arises due to side lobes of an NC-OFDM signal in the frequency domain, and it interferes with the spectrum for unlicensed users. A high PAPR occurs due to the inverse fast Fourier transform (IFFT) block used in an NC-OFDM system, and it induces nonlinear effects in power amplifiers. In this study, we propose an algorithm called "Alternative Projections onto Convex and Non-Convex Sets" that reduces the OBP and PAPR simultaneously. The alternate projections are performed onto these sets to form an iteration, and it converges to the specified limits of in-band-power, peak amplitude, and OBP. Furthermore, simulations show that the bit error rate performance is not degraded while reducing OBP and PAPR.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2016.11a
• /
• pp.3-32
• /
• 2016

High power impulse magnetron sputtering (HiPIMS) technique has been developed for more than 15 years. It is characterized by its ultra-high peak current and peak power density to obtain unique thin film properties, such as high hardness, good adhesion and tribological performance. However, its low deposition rate makes it hard to be applied in industries. In this work, the development of HiPIMS system and integration of radio frequency (RF) or mid-frequency (MF) power supplies were introduced. Effects of duty cycle and repetition frequency on the microstructure, mechanical property, optical and electrical properties of some binary, ternary and quarternary nitride coatings and oxide thin films were discussed. It can be observed that the deposition rate was effectively increased by the superimposed HiPIMS with RF or MF power. High hardness, good adhesion and sufficient wear resistance can be obtained through a proper adjustment of processing parameters of HiPIMS power system.

• Proceedings of the KIPE Conference
• /
• 2009.11a
• /
• pp.249-251
• /
• 2009

In this paper, we present a study on the 50kW class power station development using lithium-polymer battery. The 50kW class power station purposes to compensate for peak load using 326[V] lithium-polymer battery bank. The output voltage is 380[V] in three-phase, peak load compensation is controlled based on load power. Finally, a 50kW power station system is built to verify the experiment.

• Proceedings of the KIPE Conference
• /
• 1999.07a
• /
• pp.431-434
• /
• 1999

This paper presents design of controllers for battery energy storage system. The proposed battery energy storage system can be controlled to operate in the power conditioning mode or the inverter mode. The operation of this mode further divided into three cases: (a) in the peak load period, the load power supplied from the utility is minimized as far as possible; (b) in the off-peak load period, the utility supplies power to the load and charges the battery bank with automatic charging control; (c) in the medium load period, to save battery energy the real power flow out of the battery energy storage system is minimized. Besides, in all cases, the proposed battery energy storage system also automatically compensates the harmonics, subharmonics and reactive power factor in the utility side are much improved. Simulation results are presented by the effectiveness of the proposed controllers for battery energy storge system.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.7 no.4
• /
• pp.241-246
• /
• 2007

This paper presents two novel compensation circuits for leakage current and power supply noise (PSN) in phase locked loop (PLL) using a nanometer CMOS technology. The leakage compensation circuit reduces the leakage current of the charge pump circuit and the PSN compensation circuit decreases the effect of power supply variation on the output frequency of VCO. The PLL design is based on a 32nm predictive CMOS technology and uses a 0.9 V power supply voltage. The simulation results show that the proposed PLL achieves 88% jitter reduction at 440 MHz output frequency compared to the PLL without leakage compensator and its output frequency drift is little to 20% power supply voltage variations. The PLL has an output frequency range of 40 $M{\sim}725$ MHz with a multiplication range of 1-1023, and the RMS and peak-to-peak jitter are 5psec and 42.7 psec, respectively.

• Proceedings of the KIEE Conference
• /
• 2006.07b
• /
• pp.1079-1080
• /
• 2006

This paper presents the methods to save energy by using load consumption pattern analysis. Base on the substation annual power usage data, the characteristic of the substation power consumption have investigated. With this investigation effective electrical billing condition and the control target load has been determined. Most of power usage comes from the motor car, so power system and load table of motor car were reviewed. And in the metropolitan area the peak power consumption occurs at summer or winter rush hours because of its typical characteristics. From this data control point of time are determined. Through the whole study the methode to control the power Peak consumption are proposed and prototype was designed.