• 한국의류학회지
• /
• 제25권4호
• /
• pp.719-730
• /
• 2001

The purpose of this study is to develop the basic patterns of adult womens brassiere therewith, provide for some basic data useful to the brassiere manufacturing which are both functional and fitting. For this purpose, 220 adults women(aged between 20 and 59) were sampled to be measured for their body sizes and tested for their brassiere wearing. The collected data were statistically processed using the SAS 6.12 for Means, Standard Deviation, etc. The results of this study can be summarized as follows; 1. In order to develop the basic patterns of adult womens brassieres, 75A size was selected out of 12 size combination(3 women per 75A size) and then, their brassiere fitting was tested. As a result, the fronts of the basic patterns were found to have such problems as undone front center, poor levelling of upper cups bottom line or lower cups top line, poor shape of upper cups outside top line and shoulder strip position. On the other hand, n the rear side of the basic patterns, the central part of the wing was slightly lifted, while the wing width and straps interval did not befit the full-cup brassiere. The result of this first brassiere fitting test showed that the functionality and aesthetics of the basic pattern brassieres were more or less satisfactory, and thus, the problems were address for the second test. In the second test, the aesthetics, breast-shaping effect and functionality of the basic pattern brassieres were much improved. 2. The basic patterns of adult womens brassieres were characterized by a round cup wired as well as a full cup embracing the entire breasts. Each basic pattern which consisted of upper and lower cups was shaped \"straight(-)\". The basic sizes adopted at the first design stage (see fig. 1-2) was 75A of which was designed as upper foundation basic pattern. At the second stage, the upper body foundation pattern were used to design lower cup, upper cup, front panel and wing in their order.(see fig. 3-5, fig. 8)5, fig. 8)

• 한국의류학회지
• /
• 제22권8호
• /
• pp.1001-1010
• /
• 1998

The purpose of this study was to investigate the images and characteristic formative elements of Korean traditional patterns. The Korean pattern image could be interpreted into visual elements of design based on the images, the characteristic formative elements of Korean traditional patterns, and their relationships. Fourteen patterns selected from 5 groups of Korean patterns were used as stimuli. An image evaluation using a 2-point sementica scale of 19 bipolar adjectives, and an impression evaluation of which results were presented by visual drawing using lines and shapes were carried out. The data were analyzed by correspondence analysis and cluster analysis. The major findings are as follows; 1. Fourteen patterns and 19 adjectives were marked on a perception map composed of two (x and y-) axes. The bipoles of x- and y axes were soft-hard and splendid-artless, respectively. 2. Four clusters semerged to account for the dimensional sturucture of 14 patterns and 19 adjectives. These were splendid image, soft image, individualistic image, and sophisticated image. However there was no pattern which belonged to the cluster, sophisticated image. The Korean pattern image was founded to be better related to the kind of patterns than the type of patterns. 3. The characteristic formative elements obtained from the impression test were contour of motif, repeated line or shape, various curved lines, and decorative elements. 4. The splendid image was related to Bongwhang patterns and detailed line and complexity. The individualistic image was related to the abstractive form of Bongwhang pattern and the decorative form of Cloud pattern both of which have the characteristics of point-symmetry and abstraction, and Turtle-back pattern. In this case, the related charac-teristic formative element was identified to be repeated lines. The soft image was related to Moran, Cloud, and Taegeuk patterns. The related characteristic elements were various types of curved lines, decorative elements, and rounded contours.

• 한국의류산업학회지
• /
• 제10권6호
• /
• pp.989-996
• /
• 2008

The purpose of this study is to provide the basic knowledge for the pattern development of a flared skirt. Two flat pattern (FP) methods, the concentric circle method and the corrected concentric circle method, and a draping were used for pattern making. Using these patterns, skirts were made with lengthwise grain in the centerline. The influence of pattern making method on the silhouette of the flared skirt was evaluated by the hemlines formed at the skirt worn in a dress form. Moreover, the combined influence of pattern making method and cutting direction on the silhouette of the flared skirt was examined with the draping pattern (DP) skirt and a FP skirt with $45^{\circ}$ bias grain in the centerline. The DP skirt had more uniform nodes and formed a stable wave form than the FP skirts throughout the whole hemlines. The number of nodes was reduced with lining in the two FP skirts, whereas the number of nodes was not changed in the DP skirt. The unit wave form of all the skirts by three patterns showed long loop form, and the slope angles of the unit wave form of the two FP skirts were higher than that of the DP skirt. The silhouette of the flared skirt was highly influenced by the shape of the waist circumference line in patterns. The DP skirt with lengthwise grain in the centerline showed good silhouette with uniform nodes and high marking efficiency, compared to the FP skirt with $45^{\circ}$ bias grain in the centerline.

• 한국의류산업학회지
• /
• 제13권1호
• /
• pp.116-129
• /
• 2011

The purpose of this study is to research on changes of body surface according to golf movements in designs of golf slacks pattern and reflect it to designs of golf slacks pattern to enhance adaptability. For the first stage of this study, length of body surface was analyzed by using 3D body shape. In second stage, analysis of wearing test of golf slacks is performed to extract major pattern design factor of golf slacks and then research patterns were designed. In third stage, 4 differently designed 1st, 2nd slacks were used for analysis of 3D Clothing air volume. The results of this research is as follow. The variation rate of body surface length according to golf swing posture resulted the longest on back swing posture and follow through posture. Waist circumference-omphalion, thigh and ankle circumference increased more than 10% of body surface during golf swing. Front waist circumference-omphalion, right waist to hip length, left waist to hip length and right back center length were decreased more than 10%. As a result of analysis on measurements of 1st slacks pattern design, waist front center getting in values, waist front center going down value, front hip width, and front crotch extension had similar industrial pattern design. Back center line angle, back crotch extension, and knee center point~back waist center point had significant differences. The designs and ease proposed for golf slacks pattern in this study are waist circumference 75.5 cm(1.8 cm, 2.38%), hip circumference 95 cm(2 cm, 2.11%), crotch length(front: -0.8 cm, -1.25%; rear: -1.8 cm, -2.83%), slacks length 96c m, gradient of C.B.L $10^{\circ}$, crotch extension (back 9.2~10.4 cm, front 3.2 cm).

• 한국의류학회지
• /
• 제32권5호
• /
• pp.846-858
• /
• 2008

This study was designed to propose a method to draft bodice block pattern from 3D body scan data. Subjects were ten elderly women in their 60's, who wear basic size(B: 94cm, W: 82cm) garment. Scanning was done using 3D whole body scanner(WB4, Cyberware). Measurements for 3D data and cross section were attained using Auto CAD, by which a upper bodice pattern for elderly women was drawn on the basis of short measured method. The results are as following: As for most items, no significant differences were shown between measurements from Martin's anthropometry and those from 3D scan data, suggesting measurement from 3D scan data could be used to draft a pattern. The drafting equations acquired were as follows; width of pattern=B/2+5.5, width of waist=W/2+3.5cm, dart amount=8cm. Dart distributions were 23%(B.P.) : 20%(front armpit) : 17%(side seam) : 18%(back armpit) : 15%(back protruded point) : 7% (center back line). Through wearing test using 5-point Likert scale, resultant pattern was evaluated as appropriate for elderly women's pattern to get over 4 point. As a result, it might be said that 3D scanning application is effective for elderly women in that it doesn't take time so much as Martin's anthropometry and that their body shape vary compared with those of young women.

• 한국정보통신학회논문지
• /
• 제23권11호
• /
• pp.1471-1477
• /
• 2019

스마트폰에는 현재 다양한 보안 방식이 사용되고 있다. 그중에서도 핀 번호와 패턴 잠금 방식은 초기 스마트폰부터 사용되었을 정도로 오래 사용되었다. 하지만 패턴 잠금 방식은 오래 사용된 만큼 보안이 취약하다. 핀 번호 방식의 보안 강도가 약간 높은 정도라면 패턴 잠금 방식은 중간 정도에 그친다. 그럼에도 많은 스마트폰 사용자들은 패턴 잠금 방식을 이용하고 있는데 아직 생체보안을 지원하지 않는 기종을 사용하는 사용자가 있기 때문이다. 생체보안을 지원하지 않는 기종에서 제일 편리한 보안 방식은 패턴 잠금 방식이다. 그러나 기존의 패턴 잠금 방식은 Shoulder surfing attack과 Smudge attack에 취약하다. 따라서 패턴 잠금 방식의 편리성을 유지하면서 동시에 기존 방식의 취약점을 해결하는 방식을 제안하고자 한다. 제안하는 방식은 화면에 배치되는 각각의 점을 원형으로 배치한 뒤 무작위로 숫자를 부여하는 잠금 방식이다. 본 방식을 도입하게 된다면 기존의 취약점을 상당히 해결할 수 있다. 즉, 기존의 패턴 잠금 방식에 비해 보안성을 높일 수 있다.

• 한국항행학회논문지
• /
• 제11권1호
• /
• pp.59-63
• /
• 2007

본 논문은 윤곽선이 불분명한 상황에서 체형의 윤곽선과 신체 내부의 그리드 패턴들을 추출하기 위한 이미지 분할 알고리즘을 서술한다. 이미지 분할 방법은 문턱 값을 이용한 이진화 기법을 사용한다. 복잡한 형상을 지닌 물체의 3차원 정보를 추출하기 위한 노이즈 제거 알고리즘은 $3{\times}3$ 하이브리드 고역통과 필터 방법을 제안한다. 본 하이브리드 고역통과 필터 알고리즘은 노이즈 제거 시간이 기존 방법에 대하여 훨씬 단축되기 때문에 3차원 체형, CAD 시스템, 공장자동화와 같은 복잡한 형상을 지닌 물체의 3차원 정보를 추출하는데 적용할 수 있다.

• Journal of Biosystems Engineering
• /
• 제28권5호
• /
• pp.421-428
• /
• 2003

This study was conducted to determine the optimum blade shape for peeling Altari radish. To figure out the required peeling force according to various angles of blade and rakes of peeling cutter, two peeling tests such as circumferential peeling and longitudinal peeling of Altari radish were carried out. Based on the pretest results, which performed to investigate the applicability of the optimum shape of cutter and to find out the cutting pattern according to the lapse of days after harvesting the radish, the peeling depth and width of the blade were fixed at 2 mm and 10 mm. From two methods of circumferential and longitudinal peeling test, the angles of rake and blade as cutter shape factors were affected on peeling force. But the peeling speed was not affected on it under the safety speed as 0.2 m/s, without blade vibrating on peeling operation. The rake angle was more effective factor than the blade angle, and the optimum angles of blade and rake were 10$^{\circ}$ and 55$^{\circ}$ respectively. The cutting surface by the longitudinal peeling was more smooth than that by the circumferential peeling. There was no problem in peeling work during 4 days after harvest because the freshness of the Altari radish was maintained.

• 한국주조공학회지
• /
• 제9권1호
• /
• pp.58-66
• /
• 1989

The effect of heat treating temperature and ${\alpha}$ phase In the ${\beta}$ phase matrix were investigated for ${\beta}-CuZnAl$ shape memory alloys by tension test, fatigue test, and shape memory effect test. After heat treatment at $677^{\circ}C$, $750^{\circ}C$, $800^{\circ}C$ and $850^{\circ}C$ for 10 min. respectively, static fracture stress(${\sigma}_f$), fatigue fracture stress(${\tau}_{max}$) at $10^6$ cycle, and elongation(${\epsilon}_f$) was $24.2kg/mm^2$, $17.21kg/mm^2$ and 11.8%, respectively. As heat treating temperature decreased, fracture surfaces of the specimens were changed from the intergranular to the transgranular fracture mode. Especially, the a phase precipitated in the ${\beta}$ phase matrix had an effect on crack propagation and the fracture surface was characterized by dimple-like pattern when crack propagated in transgranular cracking mode. Precipitation of the ${\alpha}$ phase in the ${\beta}$ phase matrix lowered the transformation temperature by $10^{\circ}C$, and about 2.5 vol.% ${\alpha}$ phase did not affect the shape memory effect examined by the bending test.

• 한국융합학회논문지
• /
• 제11권1호
• /
• pp.175-180
• /
• 2020

본 연구에서는 미세패턴 성형이 가능하도록 개발된 초음파 미세패턴 제조시스템을 이용하여 RFID TAG 안테나 형상의 미세패턴 성형기술을 개발하였다. 미세패턴 제조시스템에 종진동 모드의 초음파 공구 혼을 설치하여 절연시트 표면에 RFID TAG 안테나 형상의 미세패턴 안테나 형상을 초음파 압입 성형공정 기술을 개발하였다. 초음파 성형기술은 60kHz 공구 혼을 공진설계 기법을 적용하여 제작하였고, 미세패턴 제조시스템을 이용하여 200㎛ 이하의 절연 시트지에 두께가 25㎛의 코일 와이어를 초음파 압입 성형을 할 수 있다. 초음파 압입 성형 시 코일 와이어의 단선, 박리 및 꼬임 현상 없이 최소선폭 150㎛인 안테나 형상을 성형할 수 있었다.