• 한국안전학회지
• /
• 제35권3호
• /
• pp.96-104
• /
• 2020

The numerical simulations were conducted to investigate the thermal-fluid phenomena occurred inside the experimental apparatus during a PCCS, used to remove heat released in accidents from a containment of light water nuclear power plant, operation. Numerical simulations of the flow and heat transfer caused by wall condensation inside the containment simulation vessel (CSV), which equipped with 18 vertical heat exchanger tubes, were conducted using the commercial computational fluid dynamics (CFD) software ANSYS-CFX. Shear stress transport (SST) and the wall condensation model were used for turbulence closure and wall condensation, respectively. The simulation using the actual size of the apparatus. However, rather than simulating the whole experimental apparatus in consideration of the experimental cases, calculation resources, and calculation time, the simulation model was prepared only in CSV. Selective simulation was conducted to verify the effects of non-condensable gas(NC gas) concentration, CSV internal pressure, and wall sub-cooling conditions. First, as a result of the internal flow of CSV, it was observed that downward flow due to condensation occurred surface of the vertical tube and upward flow occurred in the distant place. Natural convection occurred actively around the heat exchanger tube. Due to this rising and falling internal flow, natural circulation occurred actively around the heat exchanger tubes. Next, in order to check the performance of built-in condensation model using according to the non-condensable gas concentration, CSV internal flow and wall sub-cooling, the heat flux values were compared with the experimental results. On average, the results were underestimated with and error of about 25%. In addition, the influence of CSV internal pressure and wall sub-cooling was small, but when the condensate was highly generated due to the low non-condensable gas concentration, the error was large compared to the experimental values. This is considered to be due to the nature of the condensation model of the CFX code. However, in spite of the limitations of CFD, it is valid to use the built-in condensation model of CFD for PCCS performance prediction from a conservative perspective.

• 한국산업보건학회지
• /
• 제4권2호
• /
• pp.127-136
• /
• 1994

활성탄관을 이용한 작업환경 공기중 유기용제의 시료채취는 여러 가지 어려운 점이 있으나 확산형 시료포집기는 이러한 점을 보완하는 새로운 포집기이다. 따라서 본 연구는 확산형 시료포집기가 혼합 유기용제를 사용하는 사업장을 대상으로 확산형 포집기와 활성탄관을 이용, 한 근로자에 대하여 동시에 각 1개씩, 총 181개의 시료를 포집하여 활성탄과 어떠한 차이가 있는 가를 확인하며, 고전적인 활성탄관 시료채취법을 대신할 수 있는 가를 확인하기 위하여 시도한 바 몇가지의 결과를 얻어 보고하는 바이다. 1. 활성탄관 시료포집기에 비하여 확산형의 시료포집기는 톨루엔(toluene), 키시렌(xylene) 등의 방향족 화합물은 다소 높은 농도를 나타내나 전반적으로 통계적인 유의성은 없었다. 2. 엠이케이(methyl ethyl ketone)와 시크로헥사논(c-hexanone)에 대하여 확산형 포집기는 적어도 저농도(허용농도의 1/8 및 1/10 이하농도)에서 활성탄관에 비하여 약 2배 정도 높게 측정되었다(p<0.01). 그러나 공기중 엠이케이와 시크로헥사논의 농도가 증가함에 따라서 확산형의 포집효율은 활성탄관 보다 적은 것으로 나타났다. 3. 활성탄관의 측정치(B)를 1.00으로 하였을 때 확산형 포집기(A)의 측정치 비(A/B)는 톨루엔의 경우 1.11, 키시렌은 1.07, 엠이케이는 1.63, 시크로헥사논은 3.65배 였다. 4. 활성탄관과 확산형 포집기에서의 측정치 비가 0.75-1.25 범위(${\pm}25%$)에 드는 것은 톨루엔 57%, 키시렌 74%였으며, 엠이케이 34%, 시크로헥사논은 약 32%에 불과하였다. 5. 활성탄관과 확산형 포집기에서의 측정치 간의 각 유기용제 별 상관은 톨루엔 0.963, 키시렌 0.957, 엠이케이 0.943, 시크로헥사논은 0.562로서 모두 통계적으로 유의하였다.

• 한국농공학회논문집
• /
• 제50권3호
• /
• pp.43-48
• /
• 2008

The economics of a passive solar heating system (PSHS) with the pebble bed heat storage was evaluated, and the applications of the PSHS were analyzed, in this study. The results are as follows: The heating load, solar heat gain, and stored heat/year of the PSHS in the solar house model were found to be 10,778MJ, 3,438MJ, and 11,682MJ, respectively. The yearly energy expenses of the PSHS and the alternative heating system (conventional coal heating system, CCHS), which uses coal, were found to be USD 1.60/year and USD 60.90/year, respectively, and the yearly expenses of the PSHS were found to be 38 times less than those of the alternative heating system (CCHS). If it will be supposed that the life cycle of the passive solar heating system, according to the results of the LCC analysis in the two systems, is 40 years, the total expenses for the life cycle of the PSHS and the CCHS will be USD 1,431.50 and USD 2,740.00, respectively. The period for the investment payback of the PSHS is six years.

• KIEAE Journal
• /
• 제3권3호
• /
• pp.19-25
• /
• 2003

The Address No.0 of Eco-friendly Architecture offers unique experience for those who visit the place to envisage the future architecture where nature, human and building exist in harmony. It is open to the general public including the students of elementary and secondary schools. This house has been built to provide opportunities for the general public to experience eco-friendly architecture. It's floor area is 42 pyung($140m^2$) and the overall site has the area of 180 pyung($600m^2$). The following illustrates some of its prominent features : ${\bullet}$ Remodeling of a traditional Korean residence ${\bullet}$ Application of passive solar systems ${\bullet}$ Use of clerestory windows and daylighting systems(washroom and machine room) ${\bullet}$ Operation of solar water heaters with flat plate collectors ${\bullet}$ Construction of Biotop(small ecological world) ${\bullet}$ Water circulation for Biotop by photovoltaic(150W) and wind power(400W) generation ${\bullet}$ Outdoor hot water supplied by all-glass evacuated solar tubes. Through this Address No.0 of Eco-friendly Architeture conclusions are as followings. 1. The array of tubes in collector has the best nice in that the number of tube is nine and the tilt angle is the latitude $+20^{\circ}$. 2. The thermal performance of the all-glass solar vacuum collector was excellent than of the flate-plate solar collector. 3. The adaption of new small wind power systems to buildings were proved to produce a profit if it is considered the expense of environment improvement and the wind speed increasing according to rise of building hight.

• Nuclear Engineering and Technology
• /
• 제34권2호
• /
• pp.165-175
• /
• 2002

Effects of gap sizes (3.9-44.3 mm) of vertical annuli on nucleate pool boiling heat transfer of water at atmospheric pressure have been obtained experimentally. Through the study, tubes of the closed bottom have been investigated and results are compared with those of a single unconfined tube. According to the results, the annular condition gives much increase in heat transfer coefficient at moderate heat fluxes. The increase is much enhanced 3s the gap size decreases. At the same tube wall superheat (about 3.1 K) the heat transfer coefficient for the least gap size (i.e., 3.9 mm) is more than three times greater than that of the unconfined tube. However, deterioration of heat transfer occurs at high heat flux for confined boiling.

• Restorative Dentistry and Endodontics
• /
• 제33권2호
• /
• pp.90-97
• /
• 2008

이 연구는 Clearfil SE Bond를 거친 법랑질 표면에 적용할 때, 자가부식 프라이머의 적용방식 (능동적인 또는 수동적인)과 접착레진의 도포회수 (1회 또는 2회)가 법랑질의 결합강도에 미치는 영향을 알아보기 위하여 시행하였다. 16개의 발거된 대구치 치관의 협면이나 설면에서 법랑질 절편을 만들어 4개의 군으로 배정한 다음, 1군은 프라이머를 수동적으로 적용한 후 접착레진을 1회 도포하였고, 2군은 프라이머를 능동적으로 적용한 후 접착레진을 1회 도포하였고, 3군은 프라이머를 수동적으로 적용한 후 접착레진을 2회 도포하였고, 4군은 프라이머를 능동적으로 적용한 후 접착레진을 2회 도포하였다. 적용된 접착레진을 10초간 광조사한 후, 법랑질 표면에 2-3개의 Tygon tube를 위치시키고 Clearfil AP-X를 충전하고 40초간 광조사 하였다. Universal testing machine을 이용하여 법랑질 표면에서 복합레진이 파절될 까지 분당 1.0 mm의 cross-head speed로 전단하중을 가하고 통계적으로 분석하여 다음과 같은 결과를 얻었다. 거친 법랑질에 대한 Clearfil SE Bond의 미세전단 결합강도는 자가부식 프라이머의 적용방식 보다는 접착레진의 도포회수에 의해 증가할 수 있음을 알 수 있었다.

• Journal of Korean Dental Science
• /
• 제10권1호
• /
• pp.10-21
• /
• 2017

Purpose: The purpose of this study was to investigate the electrochemical characteristics of nanotubular Ti-25Nb-xZr ternary alloys for dental implant materials. Materials and Methods: Ti-25Nb-xZr alloys with different Zr contents (0, 3, 7, and 15 wt.%) were manufactured using commercially pure titanium (CP-Ti), niobium (Nb), and zirconium (Zr) (99.95 wt.% purity). The alloys were prepared by arc melting in argon (Ar) atmosphere. The Ti-25Nb-xZr alloys were homogenized in Ar atmosphere at $1,000^{\circ}C$ for 12 hours followed by quenching into ice water. The microstructure of the Ti-25Nb-xZr alloys was examined by a field emission scanning electron microscope. The phases in the alloys were identified by an X-ray diffractometer. The chemical composition of the nanotube-formed surfaces was determined by energy-dispersive X-ray spectroscopy. Self-organized $TiO_2$ was prepared by electrochemical oxidation of the samples in a $1.0M\;H_3PO_4+0.8wt.%$ NaF electrolyte. The anodization potential was 30 V and time was 1 hour by DC supplier. Surface wettability was evaluated for both the metallographically polished and nanotube-formed surfaces using a contact-angle goniometer. The corrosion properties of the specimens were investigated using a 0.9 wt.% aqueous solution of NaCl at $36^{\circ}C{\pm}5^{\circ}C$ using a potentiodynamic polarization test. Result: Needle-like structure of Ti-25Nb-xZr alloys was transform to equiaxed structure as Zr content increased. Nanotube formed on Ti-25Nb-xZr alloys show two sizes of nanotube structure. The diameters of the large tubes decreased and small tubes increased as Zr content increased. The lower contact angles for nanotube formed Ti-25NbxZr alloys surfaces showed compare to non-nanotube formed surface. The corrosion resistance of alloy increased as Zr content increased, and nanotube formed surface showed longer the passive regions compared to non-treatment surface. Conclusion: It is confirmed that corrosion resistance of alloy increased as Zr content increased, and nanotube formed surface has longer passive region compared to without treatment surface.

• 한국안전학회지
• /
• 제35권4호
• /
• pp.84-91
• /
• 2020

The Korean nuclear industry developed the SPACE (Safety and Performance Analysis Code for nuclear power plants) code and this code adpots two-phase flows, two-fluid, three-field models which are comprised of gas, continuous liquid and droplet fields and has a capability to simulate three-dimensional model. According to the revised law by the Nuclear Safety and Security Commission (NSSC) in Korea, the multiple failure accidents that must be considered for accident management plan of nuclear power plant was determined based on the lessons learned from the Fukushima accident. Generally, to improve the reliability of the calculation results of a safety analysis code, verification work for separate and integral effect experiments is required. In this reason, the goal of this work is to verify calculation capability of SPACE code for multiple failure accident. For this purpose, it was selected the experiment which was conducted to simulate a Multiple Steam Generator Tube Rupture(MSGTR) accident with Passive Auxiliary Feedwater System(PAFS) operation by Korea Atomic Energy Research Institute (KAERI) and focused that the comparison between the experiment results and code calculation results to verify the performance of the SPACE code. The MSGR accident has a unique feature of the penetration of the barrier between the Reactor Coolant System (RCS) and the secondary system resulting from multiple failure of steam generator U-tubes. The PAFS is one of the advanced safety features with passive cooling system to replace a conventional active auxiliary feedwater system. This system is passively capable of condensing steam generated in steam generator and feeding the condensed water to the steam generator by gravity. As the results of overall system transient response using SPACE code showed similar trends with the experimental results such as the system pressure, mass flow rate, and collapsed water level in component. In conclusion, it could be concluded that the SPACE code has sufficient capability to simulate a MSGTR accident.

• 조명전기설비학회논문지
• /
• 제22권2호
• /
• pp.10-18
• /
• 2008

본 논문은 주파수 변조 기법을 도입하여 메탈 핼라이드 램프의 음향공명 현상을 제거한 수동 PFC 구조의 전자식 안정기를 설계 및 구현하였다. 제안하는 안정기는 EMI 필터, 수동 PFC 회로, 풀 브리지 인버터 및 LC 공진 타입의 점화기, 그리고 음향공명 현상을 제거하기 위한 회로로 구성되었다. 주파수 변조 기법의 도입으로 단일 주파수 구동시 문제점이였던 램프의 수명 경과에 따른 음향공명 대역이 변화와 동일한 크기의 방전관이라도 램프 제조 사마다 아크 튜브 내부에 봉입되는 물질과 압력차에 의한 음향공명 대역의 차이를 해결하였다. 개발된 prototype 1[kW] 메탈 핼라이드 램프용 전자식 안정기의 광변환 효율, 입력 PF, 입력 전류의 THD, 그리고 전력 변환 효율을 측정함으로써 성능을 입증하였다.

• 한국가스학회지
• /
• 제6권1호
• /
• pp.92-97
• /
• 2002

가스흡수식 냉온수기의 작동매체로 사용되고 있는 LiBr 수용액 중에서 열교환기 세관용 재료인 동 세관 및 동합금재인 큐프로니켈 세관의 부식특성에 관한 연두를 하기 위하여 $62\%$ LiBr 수용액 중에서 각 재료에 대한 전기화학적 분극실험을 실시하여 부식특성을 고찰한 결과 다음과 같은 결론을 얻었다 1) 열교환기 세관재의 분극저항은 $30\%$ 큐프로니켈 세관 > $10\%$ 큐프로니켈 세관 > 동 세관의 순으로 높게 나타난다 2) 큐프로니켈 세관의 개로전위는 동 세관보다 귀전위화되면서 부식전류밑도는 더 억제된다 3) $30\%$ 큐프로니켈 세관의 부동태 영역은 $10\%$ 큐프로니켈 세관보다 전위구간이 더 크게. 나타나면서 부동태유지 전류밀도는 더 낮아진다.