• 공업화학
• /
• 제32권6호
• /
• pp.700-705
• /
• 2021

본 연구에서는 하이드로늄 이온 농도를 모니터링하기 위한 티타늄(Ti) 와이어를 기반으로 하는 휴대용 일회용 pH 센서를 성공적으로 개발하였다. 센싱 전극은 Ti 와이어에 이리듐 산화물을 전기화학적으로 증착하여 제조하였고, 기준 전극으로 Ti 와이어에 Ag/AgCl 잉크를 코팅하였다. pH 센서에 두 개의 전극을 결합한 후 pH 센서를 다양한 pH 용액에 담그면 개방 회로 전위 신호를 수집할 수 있다. 상기 제조된 pH 센서는 감도, 응답 시간, 반복성, 선택도 및 안정성 측면에서 우수한 전기화학적 감지 성능을 보여 주었다. 현장 검사 응용을 시연하기 위해서 pH 센서를 모바일 애플리케이션과 통신할 수 있는 무선 전자 모듈과 통합하였다. 이 휴대용 pH 센서는 실제 샘플의 pH 변화를 정확하게 측정했으며 결과는 상용 pH 측정기의 데이터와 일치하였다.

• 센서학회지
• /
• 제22권3호
• /
• pp.207-211
• /
• 2013

In this research, the pH sensor was developed using CNT nanosheet with Nafion coating for the advanced medical sensor such as a blood gas analyzer. The CNT nanosheet was formed by dielectrophoresis and water-meniscus between cantilever-type electrodes. Then, the process of the heat annealing and the Nafion coating was conducted for reducing contact resistance and giving proton selectivity respectively. We measured the response of the pH sensor as the electrolyte-gated CNT-nanosheet field effect transistor. The sensor showed a linear current ratio in a similar range of the normal blood pH. A calibration method for decreasing of the response variation among sensors has also been introduced. Coefficient of variance of the pH sensor was decreased by applying the calibration method. A linear relation between the calibrated response of the sensors and pH variance was also obtained. Finally, the pH sensor with a high resolution was fabricated and we verify the feasibility of the sensor by applying the calibration method.

• 대한화학회지
• /
• 제64권2호
• /
• pp.74-78
• /
• 2020

산성 영역에서 작동하는 고감도 형광 pH 센서막을 제조하기 위하여 실란화된 유리 표면 상에 push-pull 공액 염료(DCMP)를 공유결합에 의해 고정화하였다. DCMP 유도체(DCMA), 2-hydroxyethyl methacrylate (HEMA)및 triethylene glycol dimethacrylate의 혼합물을 광개시 공중합하여 pH 감응성 형광센서막을 제조하였다. 분광학적 측정 결과, pH 2.0-5.0 사이에서 pH가 증가함에 따라 센서막의 흡광도가 증가하였으며, 같은 pH 범위에서 pH 증가에 따라 센서막의 형광 세기도 약 50배 정도 증가하였다. 산성 조건에서 pH 변화에 대한 센서막의 감응은 가역적이고 재현성이 우수하였다. 또한 센서막은 20-50초 사이의 비교적 짧은 감응 시간과 여러 금속이온 존재에서 수소 이온에 대해 높은 선택성을 나타내었다.

• Bulletin of the Korean Chemical Society
• /
• 제31권11호
• /
• pp.3128-3132
• /
• 2010

A disposable solid-state pH sensor was realized by utilizing two nanoporous Pt (npPt) electrodes and a copolyelectrolytic junction. One nanoporous Pt electrode was to measure the pH as an indicating electrode (pH-IE) and the other assembled with copolyelectrolytic junction was to maintain constant open circuit potential ($E_{oc}$) as a solid-state reference electrode (SSRE). The copolyelectrolytic junction was composed of cationic and anionic polymers immobilized by photo-polymerization of N,N'-methylenebisacrylamide, making buffered electrolytic environment on the SSRE. It was expected to make. The nanoporous Pt surrounded by a constant pH excellently worked as a solid state reference electrode so as to stabilize the system within 30 s and retain the electrochemical environment regardless of unknown sample solutions. Combination between the SSRE and the pH-IE commonly based on nanoporous Pt yielded a complete solid-state pH sensor that requires no internal filling solution. The solid state pH sensing chip is simple and easy to fabricate so that it could be practically used for disposable purposes. Moreover, the solid-state pH sensor successfully functions in calibration-free mode in a variety of buffers and surfactant samples.

• 센서학회지
• /
• 제31권2호
• /
• pp.85-89
• /
• 2022

We investigated a pH sensor using an Indium tin oxide (ITO) nanoparticle (NP) film printed on a flexible substrate. First, the printing precision and mechanical stability of the ITO-printed film were investigated. In particular, the factors that influence the crystallinity of ITO films were studied using X-ray diffraction pattern analysis. The response of the ITO pH sensor was calibrated using a series of standard pH solutions (pH 3-11). The pH values of various specimens were measured using an ITO pH sensor, and the results were compared with those of various pH measurement methods. As a result of the experiment, the maximum error was approximately ± 0.04 pH (0.4 %) at pH 9, which indicated that the ITO pH sensor is highly suitable for pH measurement. Finally, we used the ITO pH sensor to the measure of general specimens such as solvents and beverages and compared the results in comparison with those obtained from several conventional methods.

• 센서학회지
• /
• 제15권2호
• /
• pp.127-133
• /
• 2006

Recent studies demonstrated the ability of carbon nanotube (CNT) to promote electron transfer reactions of important compounds and to impart higher stability onto electrochemical sensors. CNT-based sensors measured by hydroxyl radical concentration or pH value suggest great promise for biosensors. This paper describes a new method for fabricating a very simple and inexpensive pH sensor compose of single walled-carbon nanotubes (SW-CNTs) using an ultra-precision spray. CNT-based sensor shows pH sensitivity in buffer solution at different pH range. Our experimental results show the sensor responses to pH buffer solution and the conductance of depends on the pH values. These results support application possibility of SW-CNTs based pH sensor for mass production.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2010년도 하계학술대회 논문집
• /
• pp.199-199
• /
• 2010

A back-gated MOSFET on silicon-on-insulator (SOI) substrate for pH sensor was investigated. We used concentrations of pH solution from 6 to 9. The fabricated back-gated MOSFET has current difference and threshold voltage shift by pH concentrations. Therefore, It can be used to simplification of conventional pH sensor.

• 센서학회지
• /
• 제26권6호
• /
• pp.414-419
• /
• 2017

The optical characteristics of cresol red, phenol red, and neutral red immobilized in the thin film were investigated with absorbance measurement in order to find a sensing part of a fiber-optic pH sensor. Sol-Gel method with tetramethyl orthosilicate as a precursor was used to immobilize the pH indicators in the thin film. The absorbance spectra were measured when pH indicators were immobilized in the film and were dissolved in the buffer solution. Experimental results showed that the absorbance spectra could be changed when the pH indicator is immobilized in the thin film. As compared with other pH indicators, the neutral red exhibited similar absorbance spectra regardless of physical conditions and was sensitive over whole pH range between 4 and 11. In addition, the absorbance ratio of base peak to acid peak tended to increase in proportion to the increase in pH. Experimental results indicate that the neutral red is a good pH indicator for fabrication of a sensing part of the fiber-optic pH sensor.

• 센서학회지
• /
• 제13권3호
• /
• pp.213-217
• /
• 2004

The general method to find a H. pylori in the stomach is the rapid urease test but it is only used to decide the infection with H. pylori. In this study, it is tried to develope fiber-optic pH sensor which can be used with gastroscop to quantify H. pylori. To measure the degree of infection with H. pylori, the color change of phenol red according to the degree of pH is measured by optical fibers with different light sources and the optimum distance from a sample to the end of sensor tip is decided by measuring the maximum reflectivity from a sample. Also the sensitivity study is carried out to decide the optimum light source which has sensitive change of reflectivity to the change of pH. It is expected that the fiber-optic pH sensor which measures the degree of infection with H. pylori exactly can be developed.

• Bulletin of the Korean Chemical Society
• /
• 제31권10호
• /
• pp.2939-2942
• /
• 2010

A new high-temperature pH sensor has been successfully developed by reforming the internal reference systems of the pH sensors based on oxygen-ion conducting ceramic membrane. The conventional internal reference system, a mixture of Ni and NiO, has been replaced with partially oxidized Ni powders, where Ni and NiO coexist on the surface of particles, in order to avoid the cumbersome mixing step of Ni and NiO particles. The partially oxidized Ni particles were made by oxidizing Ni under air atmosphere at $600^{\circ}C$ and characterized by X-ray diffraction (XRD) and FTIR spectroscopy. The viability of the pH sensor developed was assessed in boric acid (1000 ppm-B)/ lithium hydroxide (1 to 3 ppm-Li) buffer solutions at $280^{\circ}C$. The pH sensor showed excellent accuracy with a small error less than ${\pm}0.2$ pH units.